• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.140-145
• /
• 2005

The desulfurization abilities using GC/microreactor have been examined for $CuO-Fe_2O_3$ sorbents with respect to calcination temperatures of 700, 900 and $1,100^{\circ}C$. CuO was used as a main active component, $Fe_2O_3$ was used as an additive one and 25 wt% $SiO_2$ was used as a support. The desulfurization reaction temperature was $500^{\circ}C$ and the regeneration reaction temperature was $700^{\circ}C$. From the XRD results, the $CuFeO_2$ compound has been observed for the fresh sorbent calcined at $1,100^{\circ}C$ and the $CuFeS_2$ compound for the reacted sorbent calcined at $1,100^{\circ}C$. By the BET results, however any significant differences among sorbents calcined at the three different temperatures of 700, 900 and $1,100^{\circ}C$ haven't been observed. Especially CFS1 (CuO : $Fe_2O_3$ : $SiO_2$=67.5 wt% : 7.5 wt% : 25 wt%) sorbent calcined at $1,100^{\circ}C$ maintained about 10 g sulfur/100 g sorbent for 100 cycles by the cyclic test.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2000.11a
• /
• pp.155-155
• /
• 2000

• Journal of the Mineralogical Society of Korea
• /
• v.20 no.4
• /
• pp.367-376
• /
• 2007

Aenigmatite, $Na_4(Fe^{2+},Ti,Fe^{3+}){_{12}}(Fe^{3+},Si){_{12}}O_{40}$, is a common constituent of sodium-rich alkaline igneous rocks and is classified a an open-branched single-chain silicate. $M\ddot{o}ssbauer$ spectroscopy of three natural aenigmatite specimens were done and the detailed crystal chemistry was obtained. Fitting of $M\ddot{o}ssbauer$ spectra led to the resolution of nine peaks. They consist of three doublets of $Fe^{2+}/oct$ and one merged peak at low velocity matching to two small peaks at high velocity which were assigned to $Fe^{3+}/tet\;and\;Fe^{2+}/oct$, respectively. Using the peak area for $Fe^{2+}\;and\;Fe^{3+}$ peaks, analytical data were recalculated. Precise assignment of $Fe^{2+}\;and\;Fe^{3+}$ ions in tetrahderal and octahedral sites revealed detailed crystal chemistry of aenigmatite. The existence of significant amounts of $Fe^{3+}/tet$ indicates that $Fe^{3+}$ has preference over $Al^{3+}$ for the tetrahedral sites. Crystal chemistry of aenigmatite (AEN1) yields the formula of $(Na_{3.97}Ca_{0.03})(Ca_{0.11}Mn_{0.59}Fe^{2+}{_{8.07}}Ti_{2.07}Mg_{0.70}Fe^{3+}{_{0.43}}Al_{0.04})(Fe^{3+}{_{0.56}}Al_{0.18}Si_{11.26})O_{40}$.

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.705-711
• /
• 1989

The glass-ceramics was prepared with the scoria(CaO-MgO-Al2O3-SiO2 system) of the locally occurring volcanic ejecta containing 10-13w/o of (FeO＋Fe2O3) by melting at 140$0^{\circ}C$ for 4 hours and thermally treated for nucleation and crystallization. The sucrose was added to the scoria to adjust the Fe2+/Fe3+ ratio during the melting process. The addition of 1-2w/o of sucrose showed the glass-ceramics body with the finest particle developed and dispersed over the entire range. It is concluded that the impurity content of iron oxide and titanium oxide play the most-influencial effect on the crystallization. When 1-2w/o of sucrose was added to the scoria, the value of Fe2+/Fe3+ ratio was 0.93-1.32 and showed the best result of crystallization. The nucleation temperature and time were calculated by the measurements of exothermic peak temperatures of DTA for quenched and thermally treated glasses. The nucleation temperature of scoria glass without the addition of sucrose was estimated as 75$0^{\circ}C$, but the addition of sucrose by 2w/o showed the nucleation temperature 6$25^{\circ}C$. The nucleation time was calculated with the same DTA curves. The nucleation times estimated were about 150min. for both of glasses without and with sucrose added. Finally, the activation energies for crystallization were calculated with the DTA data. The calculated activation energies were 143 Kcal/mole for the glass without addition of sucrose and 90Kcal/mole, 87Kcal/mole, 85Kcal/mole and 71Kcal/mole for the glasses of 1w/o, 2w/o, 3w/o and 4w/o addition respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.4
• /
• pp.1883-1889
• /
• 2013

Although Fe-Si based alloy has lower figure of merit than Si-Ge alloy applied for space probe, its low cost related to abundant raw material, rather simple processing, high temperature resistance and reliability up to $800^{\circ}C$ made it one of the most promising middle temperature thermoelectric generation materials. The effect of particle size and additive on the thermoelectric properties of p-$FeSi_2$ prepared by a RF inductive furnace was investigated. The electrical conductivity increased slightly with decreasing particle size and hence better grain-to-grain connectivity due to the increase of density. The Seebeck coefficient exhibited the maximum value at about 600~800K and decreased slightly with increasing particle size. This must be due to the amount of residual metallic phase ${\varepsilon}$-FeSi. $Fe_2O_3$ and/or $Fe_3O_4$-doped specimens showed the higher electrical conductivity and the lower Seebeck coefficient due to increase of the metallic phase and Si-vacancy. On the other hand, $SiO_2$-doped specimen showed the higher electrical conductivity and the higher Seebeck coefficients.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.454-457
• /
• 2011

We report the preparation of nanocrystalline cobalt ferrite, $CoFe_2O_4$, particles using recycled $Co_3O_4$ and their surface coating with silica using micro emulsion method. Firstly, the $Co_3O_4$ powders were separated from waste cemented carbide with acid-base chemical treatment. The cobalt ferrite nanoparticles with the size 10 nm are prepared by thermal decomposition method using recycled $Co_3O_4$. $SiO_2$ was coated onto the $CoFe_2O_4$ particles by the micro-emulsion method. The $SiO_2$-coated $CoFe_2O_4$ particles were studied their physical properties and characterized by X-ray diffraction (XRD), high resolution-transmission electron microscopy (TEM) analysis and CIE Lab value.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.511-516
• /
• 1992

In this study, SiC powder and Si powder were used as the raw materials. Mixture was prepared with addition of Al2O3 and Fe2O3 at 0.1~0.5wt% respectively. After this step, the mixture was pressed and nitrided for 30 hrs at 140$0^{\circ}C$ under NH3-N2 atmosphere. Mechanical properties of sintered specimens were investigated from measurement of porosity, bulk density and three point bending test. nitration reaction extent was observed at the change of mass before and after reaction, and the microstructure and the change of $\alpha$-Si3N4 and $\beta$-Si3N4 were observed by XRD and SEM. In the current work, the results are as follows 1. When Fe2O3 added, the nitridation increased with the content of Fe2O3, and the bending strength was increased from 0.1 wt% to 0.3 wt%, and decreased to 0.5 wt%. 2. When Al2O3 added, the nitridation and the bending strength increased little by little with the content of Al2O3 3. The bending strength of the specimen added with Fe2O3 were higher than that with Al2O3. Because the specimens contained Fe2O3 had much more the whisker type crystal of Si3N4 contributing to strength than contained Al2O3.

• Journal of the Mineralogical Society of Korea
• /
• v.17 no.4
• /
• pp.309-325
• /
• 2004

The Cannington Ag-Pb-Zn deposit, northwest Queensland, Australia developed around the host rocks composing banded and migmatitic gneisses, sillimanite-garnet schist and amphibolite. Three crystal habits of sillimanite, gahnite (Zn-spinel) and garnet porphyroblasts occurred on the host rocks of the Cannington deposit could be used to delineate metamorphism that closely associated with Zn-mineralization in the deposit. Linkages the metamorphism to Zinc-mineralization is determined in four chemical systems, KFMASH (K$_2$O-FeO-MgO-Al$_2$O$_3$-SiO$_2$-$H_2O$), KFMASHTO (K$_2$O-FeO-MgO-Al$_2$O$_3$-SiO$_2$-$H_2O$-TiO$_2$-Fe$_2$O$_3$), NCKFMASH (Na$_2$O-CaO-K$_2$O-FeO-MgO-AlO$_3$-SiO$_2$-$H_2O$) and MnNCK-FMASH (MnO-Na$_2$O-CaO-K$_2$O-FeO-MgO-AlO$_3$-SiO$_2$-$H_2O$), using THERMOCALC program (version 3.1; Powell and Holland 1988). Partial melting in MnNCKFMASH and NCKFMASH systems occurs at lower temperature than in the KFMASH and KFMASHTO systems. The partial melting temperature decreases with increasing of Na/(Na+Ca+K) of the bulk rock compositions in the MnNCKFMASH system. The host rocks have melted ca 15 vol.% in the MnNCKFMASH system at peak metamorphic conditions (634$\pm$62$^{\circ}C$ and 4.8$\pm$1.3 kbar), but partial melting have not occurred in KFMASHTO system. Based on calculations of sillimanite isograd in different systems and sillimanite modal pro-portion, prismatic and rhombic sillimanite and gahnite porphyroblasts including prismatic sillimanite inclusion probably have resulted from pressure and temperature increasing through partial melting (from 550～$600^{\circ}C$, 2.0～3.0 kbar to 700～75$0^{\circ}C$, 5.0～7.0 kbar), furthermore have experienced N-S then W-E crustal shortening during D$_1$ and D$_2$ deformation. Consequently, Zinc mineralization related to gahnite growth occurred during D$_2$ and was redistributed and upgraded by partial melting and retrograde metamorphism into structural and rheological sites during shearing in D$_3$.

• Journal of the Korean Chemical Society
• /
• v.59 no.5
• /
• pp.397-406
• /
• 2015

ZnO, II-VI group inorganic compound semi-conductor, has been receiving much attention due to its wide applications in various fields. Since the ZnO has 3.37 eV of a wide band gap and 60 meV of big excitation binding energy, it is well-known material for various uses such the optical property, a semi-conductor, magnetism, antibiosis, photocatalyst, etc. When applied in the field of photocatalyst, many research studies have been actively conducted regarding magnetic materials and the core-shell structure to take on the need of recycling used materials. In this paper, magnetic core-shell ZnFe₂O₄@SiO₂ nanoparticles (NPs) have been successfully synthesized through three steps. In order to analyze the structural characteristics of the synthesized substances, X-ray diffraction (XRD), scanning electron microscopy (SEM), and Fourier transform infrared spectroscopy (FT-IR) were used. The spinel structure of ZnFe₂O₄ and the wurtzite structure of ZnO were confirmed by XRD, and ZnO production rate was confirmed through the analysis of different concentrations of the precursors. The surface change of the synthesized materials was confirmed by SEM. The formation of SiO₂ layer and the synthesis of ZnFe₂O₄@ZnO@SiO₂ NPs were finally verified through the bond of Fe-O, Zn-O and Si-O-Si by FT-IR. The magnetic property of the synthesized materials was analyzed through the vibrating sample magnetometer (VSM). The increase and decrease in the magnetism were respectively confirmed by the results of the formed ZnO and SiO₂ layer. The photocatalysis effect of the synthesized ZnFe₂O₄ @ZnO@SiO₂ NPs was experimented in a black box (dark room) using methylene blue (MB) under UV irradiation.

• Journal of the Korean Ceramic Society
• /
• v.31 no.9
• /
• pp.1069-1075
• /
• 1994

When ceramics are used as the parts of an engine and a machine, the tribological properties are very important. For the preparation of the resistance material for wear applications by the method of Reaction-Bonded Sintering, metal silicon and carbon black are mixed up into SiC powder, and Al2O3 and Fe2O3 are put as an additive. As the general properties, the bending strength and water absortion are measured in the normal temperature and the phase changies are investigated with XRD. The property of the resistance for wear applications is measured with the amount of friction and wear, friction coefficient and maximum asperties. And, the surface of wear is observed with SEM. With the results of this study, the optimal mol ratio of Si : C and the suitable quantity of the mixture of SiC are 7 : 3 and 40 wt%, respectively. In the case of the addition of Al2O3 (2 wt%), the resistance for friction and wear applications is prominent. The bending strength showed the highest peak when Al2O3 (4 wt%) and Fe2O3 (4 wt%) were added. The properties of friction and wear were related with the propagation velocity of crack rather than the bending strength.