• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.167-170
• /
• 2001

The stochiometric mix of evaporating materials for the CdGa$_2$Se$_4$ single crystal thin films was prepared from horizontal furnace. To obtain the single crystal thin films, CdGa$_2$Se$_4$ mixed crystal was deposited on thoroughly etched semi-insulating GaAs(100) substrate by the Hot Wall Epitaxy (HWE) system. The source and substrate temperature were 630$^{\circ}C$ and 420$^{\circ}C$, respectively. The crystalline structure of single crystal thin films was investigated by the photoluminescence and double crystal X-ray diffraction (DCXD). The carrier density and mobility of CdGa$_2$Se$_4$ single crystal thin films measured from Hall erect by van der Pauw method are 8.27x10$\^$17/ cm$\^$-3/, 345 $\textrm{cm}^2$/V$.$s at 293 K, respectively. From the Photocurrent spectrum by illumination of perpendicular light on the c-axis of the CuInSe$_2$ single crystal thin film, we have found that the values of spin orbit splitting ΔSo and the crystal field splitting ΔCr were 106.5 meV and 418.9 meV at 10 K, respectively. From the photoluminescence measurement on CdGa$_2$Se$_4$ single crystal thin film, we observed free excition (E$\_$X/) existing only high quality crystal and neutral bound exiciton (D$\^$0/,X) having very strong peak intensity. Then, the full-width-at-half-maximum(FWHM) and binding energy of neutral donor bound excision were 8 meV and 13.7 meV, respectivity. By Haynes rule, an activation energy of impurity was 137 meV,

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.79-79
• /
• 2010

저온용 무연 솔더의 대표 조성으로 고려되고 있는 Sn-58Bi(융점: $138^{\circ}C$) 공정(eutectic) 조성은 우수한 강도에도 불구하고 연성(ductility) 측면에서의 문제점이 지속적으로 보고되고 있다. 따라서 이 합금계의 연성을 최대로 개선시킬 수 있으면서도 실제 상용화가 가능한 합금 조성의 개발 연구가 요청된다. 본 연구에서는 Sn-Bi 2원계 조성에서 최대의 연성을 나타내는 것으로 보고된 Sn-40Bi 조성에 미량의 합금원소를 첨가함으로써 최대의 연성을 확보하는 한편, 그 연성 특성이 변형속도에 어느 정도 민감한지를 인장 실험을 통해 결정하고자 하였다. 합금원소로는 0.1~0.5 wt%의 Ag, Mn, In, Cu를 선택하였으며, 인장 시편을 제조하여 $10^{-2}$, $10^{-3}$, $10^{-4}\;s^{-1}$의 3종류로 변형속도를 변형시켜가며 응력-변형 곡선(stress-strain curve)을 측정하였고, 조성별, 변형속도별로 최대인장강도(ultimate tensile stress, UTS) 및 연신율 결과들을 정리하였다. 합금원소를 첨가한 조성의 경우는 모든 시험 조건에서 Sn-40Bi보다 우수한 연신률을 나타내는 것으로 측정되었으나, $10^{-2}\;s^{-1}$의 빠른 변형속도에서는 그 향상 정도가 상대적으로 감소하는 경향이 관찰되었다. 특히 Sn-40Bi-0.5Ag 조성의 경우 느린 변형속도에서 특히 눈에 띄는 연신률 값을 나타내며, 모든 변형속도 조건에서 가장 우수한 연성을 나타내었다. 한편 Sn-40Bi-0.1Cu 조성의 경우 변형속도에 따른 연신률의 변화 정도, 즉, 변형속도에 따른 연신률의 민감도가 매우 커 $10^{-4}\;s^{-1}$ 속도에서는 Sn-40Bi-0.5Ag에 버금가는 연신률 값이 측정되었으나, $10^{-2}\;s^{-1}$ 속도에서는 가장 나쁜 연신률 특성을 보여주었다. Sn-40Bi-0.2Mn 조성은 최고의 연신률 향상 특성을 나타내지는 않았으나, In을 첨가한 경우보다는 대체적으로 우수한 연성을 나타내었다. 이상의 각 합금별 연성 특성은 인장시험 전의 미세조직 관찰 결과와 인장시험 후 파면부의 조직변화 관찰 결과로부터 해석되었다. 그 결과 석출상의 형성 여부, 인장 시험 중 재결정 조직의 형성 여부, 라멜라(lamellar) 조직의 분율과 라멜라 간격(lamellar spacing)의 정도 또는 $\beta$-Sn과 라멜라 조직 사이의 결정립계와 라멜라 조직 내 결정립계에서의 슬라이딩 모드(sliding mode) 변형 정도, 석출상의 크기와 분포 정도 등이 연신률 및 변형속도 민감도와 같은 연성 특성에 가장 큰 영향을 미치는 인자인 것으로 분석되었다.

• Journal of the Mineralogical Society of Korea
• /
• v.19 no.3 s.49
• /
• pp.129-138
• /
• 2006

In this study, we identified the secondary precipitates from Samsan-jeil and Sambong mine, Goseong, Gyeongnam by means of scanning electron microscopy, electron probe microanalysis and X-ray powder diffraction analysis. Copper sulfide minerals had been produced from the mines during last few decades, however they are not worked. White and blue precipitates were found at the downstream of mine rock dump at Sambong mine and green one was at Samsan-jeil mine. The white precipitate covered the host rock surface with thickness of $30{\mu}m$, and is a kind of diatom with $10{\mu}m$ in length and $3{\mu}m$ in width. It is a species Fragilaria constuens, which is contained a order Pennales(pennate diatom) and lives in fresh water. The blue precipitate is the alteration product of chalcopyrite. It resultes in the increase in the ratio Cu:Fe from 5 to 13. The green precipitate has worm-like morphology with $10{\sim}20nm$ in diameter and $200{\sim}300nm$ in length. It is mainly composed of secondary copper sulfate such as woodwardite. However, it could be formed by the activity of microorganism, because the copper content is more than any secondary copper sulfate reported in copper sulfide mine. In order to identity the green precipitate exactly, the further research is needed.

• Journal of the Korean Wood Science and Technology
• /
• v.37 no.3
• /
• pp.245-254
• /
• 2009

As a substitute for CCA, which is inhibited due to its environmental pollution and human harmfulness, and CuAz and ACQ with a high cost, okara-based wood preservatives were formulated with okara hydrolyzates using copper sulfate and/or borax as a metal salt. The efficacy of the preservatives and X-ray microanalysis of wood specimens treated with the preservatives were examined to confirm the potential of the okara-based wood preservatives. Most of the preservatives showed excellent decay resistance against brown-rot fungi, Postia placenta and Gloeophyllum trabeum. The efficacy was improved when the acid concentration and temperature used for the hydrolysis of okara increased. In addition, when borax was added into copper sulfate/okara hydrolyzates preservative formulations, any decay was not found in the specimens. From the microscopic observation of the specimens treated with okara-based wood preservatives, it seems that okara is contributed to the fixing of metal salts in wood blocks. Therefore, it is speculated that okara-based wood preservatives can effectively protect wood against fungal attack as CuAz, and that the preservatives are sufficient to use as an alternative wood preservative of CCA, ACQ and CuAz.

• Progress in Medical Physics
• /
• v.20 no.4
• /
• pp.308-316
• /
• 2009

To achieve the accurate evaluation of given absorbed dose from output dose of linear accelerator photon beam through investigate the characteristics of LiF:Mg,Cu,P TLD powder. This experimental TL phosphor is performed with a commercial LiF:Mg,Cu,P powder (Supplied by PTW) and TL reader (LTM, France). The TLD was exposed to 6 MV X rays of linear accelerator photon beam with range 15 to 800 cGy in blind dose at two hospitals. The dose evaluation of TLD was through the experimental algorithms which were dose dependency, dose rate dependency, fading and powder weight dependency. The glow curve has shown the three peaks which are 110, 183 and 232 degrees of heating temperature and the main dosimetric peak showed highest TL response at 232 high temperature. In this experiments, the LiF:Mg,Cu,P phosphor has shown the 2.5 eV of electron trap energy with a second order. This experiments guided the dose evaluation accuracy is within 1% +2.58% of discrepancy. The TLD powder of LiF:Mg,Cu,P was analyzed to dosimetric characterists of electron captured energy and order by glow shape, and dose-TL response curve guided the accuracy within 1.0+2.58% of output dose discrepancy.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.133-133
• /
• 1999

We have fabricated and tested a simple circuit of the rapid single-flux-quantum(RSFQ) four-stage shift register using a single layer high-T$_c$ superconducting (HTS) YBa$_2Cu_3O_{7-x}$ (YBCO) thin film structure with 9 step-edge Josephson junctions. The circuit includes two read superconducting quantum interference devices(SQUID) and four stages. To establish a robust HTS RSFQ device fabrication process, we have focussed the reproducible process of sharp and straight step-edge formation as well as the ratio of film thickness to step height t/h. The spread of step-edge junction parameters was measured from each13 junctions with t/h=l/3, l/2, and 2/3 at various temperatures. We have demonstrated the simplified operation of the shift register at 65 K..

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.31-35
• /
• 1999

We have fabricated and tested a simple circuit of the rapid single-flux-quantum(RSFQ) four-stage shift register using a single layer high-$T_c$ superconducting (HTS) $YBa_2Cu_3O_{7-x}$ (YBCO) thin film structure with 9 step-edge Josephson junctions. The circuit includes two read superconducting quantum interference devices(SQUID) and four stages. To establish a robust HTS RSFQ device fabrication process, we have focussed on the reproducible process of sharp and straight step-edge formation as well as the ratio of film thickness to step height, t/h. The spread of step-edge junction parameters was measured from each 13 junctions with t/h=1/3, 1/2, and 2/3 at various temperatures. We have demonstrated the simplified operation of the shift register at 65 K.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.559-562
• /
• 2004

The $high-T_c$ Superconducting(HTS) antenna which consists of "H" type resonator has the benefits for the miniaturization of antenna in comparison with the microstrip antenna of the similar dimension. To fabricate the "H" type antenna HTS $YBa_2Cu_3O_{7-x}$(YBCO) thin films were deposited on MgO substrates using rf-magnetron sputtering. Standard etching processes were performed for the patterning of the "H" type antenna. For comparison between normal conducting antennas and superconducting antennas, the gold antennas with the same dimension were also fabricated. An aperture coupling was used for impedance matching between $50\Omega$ feed line and HTS radiating patch. The diverse experimental results were reported in terms of the resonant frequency, the return loss and the characteristics impedance. The "H" type superconducting antenna showed the performance of 1.36 in SWR, 24 % in efficiency, and 14.6 dB in the return loss superior to the normal conducting counterpart.

• Journal of Korean Society of Environmental Engineers
• /
• v.38 no.7
• /
• pp.343-352
• /
• 2016

Effects of grinding time and chemicals dosage in arsenic removal from contaminated paddy soil in China were investigated using lab scale attrition and froth flotation combining process. Arsenic concentration in the field soil was 76.51 mg/kg, exceeding Korean and Chinese standards, and predominant arsenic compounds fraction in sequential extraction was "residual" (over 80%). After wet sieving, soil with >2 mm and < 0.038 mm showed concentration lower than 'Warning Level' in Korea. Soil with 0.038-0.075 mm, showing the highest concentration, was discarded since it occupied minor weight fraction (10.1%). Thus soil between 0.075 and 2 mm was only used in the combining process. The highest Arsenic concentration in progeny fragments smaller than 0.038 mm reached up to 981.66 mg/kg after 5 min of attrition. Optimal dosage of collector ($C_5H_{11}OCS_2K$) and modifier ($Na_2S$ and $CuSO_4$) in froth flotation process for the selective separation of the chipped progeny particles from the parent fragments were determined both as 200 g/ton. Arsenic removal efficiency in froth flotation process was 38.47% and it was increased to 72.74% in additional flotation process, scavenging. Average arsenic concentration after overall process - wet sieving, attrition and froth flotation - was estimated to 16.45 mg/kg.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.152-159
• /
• 1999

YBa$_2Cu_3O_{7-{\delta}}$ (YBCO) films grown on CeO$_2$-buffered r-cut sapphire substrates (CbS's) were prepared and their structural and electrical properties were measured. Post-annealed CeO$_2$ films were used as buffer layers for the experiments. It turned out that the YBCO films grown on post-annealed CbS's had the rms roughness of less than 20 ${\AA}$ and peak-to-peak roughness of about 30 ${\AA}$ when the YBCO film thickness was 3000 ${\AA}$. Meanwhile, YBCO films on in-situ grown CeO$_2$ buffer layers on r-cut sapphire substrates appeared to have the peak-to-peak roughness of more than 450 ${\AA}$. X-ray diffraction data revealed that the YBCO flms were epitaxially grown along the c-axis with the typical FWHM of(005) ${\theta}$ -2 ${\theta}$ peak about 0. 16 $^{\circ}$ and ${\Delta}$ ${\omega}$ of the (005) peak about 0.5 $^{\circ}$. T$_c$ > 87 K, ${\Delta}$T < 1 K and R(look)/R(100K) ${\ge}$3 were observed from the YBCO films. Applicability of the YBCO films for high-frequency applications was described.