• Korean Journal of Materials Research
• /
• v.32 no.11
• /
• pp.481-488
• /
• 2022

The Cu₂ZnSn(S_xSe_1-x)₄ (CZTSSe) absorbers are promising thin film solar cells (TFSCs) materials, to replace existing Cu(In,Ga)Se₂ (CIGS) and CdTe photovoltaic technology. However, the best reported efficiency for a CZTSSe device, of 13.6 %, is still too low for commercial use. Recently, partially replacing the Zn²⁺ element with a Cd²⁺element has attracting attention as one of the promising strategies for improving the photovoltaic characteristics of the CZTSSe TFSCs. Cd²⁺ elements are known to improve the grain size of the CZTSSe absorber thin films and improve optoelectronic properties by suppressing potential defects, causing short-circuit current (J_sc) loss. In this study, the structural, compositional, and morphological characteristics of CZTSSe and CZCTSSe thin films were investigated using X-ray diffraction (XRD), X-ray fluorescence spectrometer (XRF), and Field-emission scanning electron microscopy (FE-SEM), respectively. The FE-SEM images revealed that the grain size improved with increasing Cd²⁺ alloying in the CZTSSe thin films. Moreover, there was a slight decrease in small grain distribution as well as voids near the CZTSSe/Mo interface after Cd²⁺ alloying. The solar cells prepared using the most promising CZTSSe absorber thin films with Cd²⁺ alloying (8 min. 30 sec.) exhibited a power conversion efficiency (PCE) of 9.33 %, J_sc of 34.0 mA/cm², and fill factor (FF) of 62.7 %, respectively.

• Journal of the Korean institute of surface engineering
• /
• v.38 no.3
• /
• pp.112-117
• /
• 2005

In this paper, CdS thin films, which were widely used as a window layer of the CdS/CdTe and the $CdS/CuInSe_2$heterojunction solar cell, were grown by chemical bath deposition, and the structural, optical and electrical properties of the films on reaction temperatures were investigated. Cadmium acetate and thiourea were used as cadmium and sulfur source, respectively. And Ammonium acetate was used as the buffer solution. As the reaction temperatures were increased, the deposition rate of CdS fllms prepared by CBD was increased and the grain size was large due to increasing reaction rate in solution, also optical transmittance of the films in visible lights was increased on rising reaction temperatures.

• Natural Product Sciences
• /
• v.21 no.1
• /
• pp.6-13
• /
• 2015

Phytochemical investigation of the aerial components of Ducrosia ismaelis Asch. led to the isolation of six known compounds, psoralen (1), isopsoralen (2), cnidioside A (3), (-)-syringaresinol-O-${\beta}$-D-glucopyranoside (4), (E)-plicatin B (5), trilinolein (6). The chemical structures of these compounds were elucidated from spectroscopic data and by comparison of these data with previously published results. The antioxidant, anti-osteoporotic and cardiovascular related activities of the isolated compounds were assessed using oxygen radical absorbance capacity (ORAC), reducing capacity, tartrate-resistant acid phosphatase (TRAP), and soluble epoxide hydrolase (sEH) inhibitory activity assays. Compounds (3-5) showed potent peroxyl radical-scavenging capacities with ORAC values of $11.06{\pm}0.39$, $7.98{\pm}0.10$, and $13.99{\pm}0.06$ Trolox equivalent (TE) at concentrations of $10{\mu}M$, respectively. Only compounds 4 and 5 was able to significantly reduce $Cu^{2+}$ ions, with a reduction value of $9.06{\pm}0.32$ and $4.61{\pm}0.00{\mu}M$ Trolox Equivalent (TE) at a concentration of $10{\mu}M$. Compound 5 at $10{\mu}M$ exhibited a potent inhibitory effect on osteoclastic TRAP activity with a TRAP value of $86.05{\pm}6.55%$ of the control. Compounds 1, 3 and 5 potently inhibited sEH activity with $IC_{50}$ values of 41.6 4.9, 16.0 1.1, and 49.0 $5.7{\mu}M$, respectively.

• Bulletin of the Korea Photovoltaic Society
• /
• v.9 no.2
• /
• pp.18-28
• /
• 2023

지구상에 풍부하며 저독성 소재인 안티모니 셀레나이드(Sb₂Se₃)는 재료가 갖는 우수한 광전자적 특성과 장기 내구성으로 차세대 태양전지 소자로 크게 주목 받고 있다. 또한, 비교적 짧은 연구기간 동안 빠른 성장 속도를 보여줬으며, 2014년 2.26%에서 8년의 연구기간 동안 약 5배인 2022년 10.57%를 달성하였다. 하지만, 여전히 기존의 칼코지나이드계 박막 태양전지인 CdTe(22.1%) 및 Cu(In,Ga)Se₂(23.35%)가 달성한 효율에 비해 낮은 변환 효율을 보이고 있으며, 이는 계면에서 발생하는 캐리어 재결합으로 인한 개방전압 손실 문제가 주 원인으로 대두되고 있다. 따라서, Sb₂Se₃ 광 흡수층에 인접한 전자 및 정공 수송층 사이에 적절한 밴드 정렬을 구축하여 캐리어 재결합 손실을 줄이는 것이 고효율 Sb₂Se₃ 태양전지를 구현하기 위한 핵심 전략 중 하나이다. 본 원고에서는 Sb₂Se₃ 광 흡수층의 기본적인 특성과 Sb₂Se₃ 태양전지의 최근 연구 성과에 대해 간략하게 설명하고자 하며, 특히 전자 및 정공 수송층 적용을 통한 에너지 밴드 정렬 최적화에 관련된 내용을 중점적으로 소개하고자 한다. 또한, Sb₂Se₃ 박막 태양전지 성능의 병목 현상을 극복하기 위한 잠재적인 연구 방향에 대해서도 논하고자 한다.

• Journal of Microbiology
• /
• v.34 no.2
• /
• pp.144-150
• /
• 1996

During growth of the genetically engineered E. coli CU103 in different media, extracellular DNAs released from the cells were studied. The extracellular DNAs released in the medium were concentrated by an thanol precipitation method and then quantified by a fluorescence method using Hoechst 33258. The released extracellular DNAs were also examined by gel electrophoresis and identified by Southern hybridization for the cloned pcbCD genes. The chromosomal DNAs and recombinant plasmid containing the cloned genes were observed to be released in an exponential growth phase. In Luria-Bertani (LB) broth and MM2-GLUCOSE, 210 and 69 ng/ml of DNAs were detected, respectively, after 3-4 days incubation at $30^{\circ}C$ and at pH 7.0. But the released DNAs were measured to be about 10-15 ng/ml in filtered river water (FW) and Tris-EDTA (TE). The at both $15^{\circ}C$ and $4^{\circ}C$, but the released DNAs were more easily degraded at the higher temperature. The extracellular DNAs were produced about 2 times more at pH 7.0 than at both pH 5.0 and pH 9.0 in MM2-glucose medium at $30^{\circ}C$. Therefore, the extracellular DNAs were found to be released actively from the cells during growth in liquid media.

• Progress in Superconductivity
• /
• v.8 no.2
• /
• pp.143-151
• /
• 2007

Accurate measurements of the microwave surface resistance (Rs) of high temperature superconductor (HTS) films are important with regard to applications of HTS materials for wireless communications. As the surface resistance values of HTS films are usually extracted from the measured unloaded quality factor ($Q_0$) of resonators made of HTS films, it is essential to measure the resonator $Q_0$ with accuracy. The $TE_{011}\;mode\;Q_0$ of sapphire resonators with the endplates made of $YBa_2Cu_3O_{7-{\delta}}$(YBCO) film on $LaAlO_3$ is measured by using the S-parameter circle-fit method at a frequency of about 19.6 GHz and temperatures of 30 K to 90 K, which is compared with the measured values by using the Lorentzian-fit method. Good agreements are found between the two sets of $Q_0$ values measured by using the two different methods whether the resonator is used in a weak-coupling scheme or a strong-coupling scheme, showing reliability of both methods fur measuring the resonator $Q_0$ accurately. The $Q_0$ of sapphire resonators with a gap between the top plate and the rest of the resonator is also discussed.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.1
• /
• pp.70-78
• /
• 2000

In applying high-${\underline{T_c}}$ superconducting material to microwave devices, Uncertainty of electromagnetics of high-${\underline{T_c}}$ superconductor(HTS) and the temperature dependence of the substrate fits with HTS thin film cause difficulty in realization of such antenna for industrial applications. It must be noted to characteristic the HTS antenna in contrast with normal conducting counterpart for this real application. In this paper, a comparative study between HTS microstrip antennas and gold antennas was reported in terms of the return loss, the characteristic impedance, efficiency, and other various characteristics. HTS thin films were $YBa_2Cu_3O_{7-x}$ (YBCO) on MgO substrates. Superconducting microstrip antennas used in this work were to directly inset a microstrip transmission line into the 50 ${\Omega}$ region of the radiating patch. Measurement results of HTS antennas and gold antennas showed that usable antennas can be made using this architecture.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.1
• /
• pp.63-69
• /
• 2000

The high-$T_c$ Superconducting (HTS) antenna which consists of "H" type resonator has the benefits for the miniaturization of antenna in comparison with the microstrip antenna of the similar dimension. To fabricate the "H" type antenna, HTS $YBa_2Cu_3O_{7-x}$ (YBCO) thin films were deposited on MgO substrates using rf-magnetron sputtering. Standard etching processes were performed for the patterning of the "H" type antenna. For comparison between normal conducting antennas and superconducting antennas, the gold antennas with the same dimension were also fabricated. An aperture coupling was used for impedance matching between $50{\Omega}$ feed line and HTS radiating patch. The diverse experimental results were reported in terms of the resonant frequency, the return loss and the characteristics impedance. The "H" type superconducting antenna showed the performance of 1.36 in SWR, 24% in efficiency, and 14.6 dB in the return loss superior of the normal conducting counterpart.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.399-399
• /
• 2012

II-V 족 화합물 반도체인 황화카드뮴(CdS)은 상온에서 2.42 eV의 밴드갭을 갖는 직접 천이형 물질로서 CdTe 또는 $CuInSe_2$와 같은 박막형 태양전지의 투과층(window layer)으로 널리 사용되고 있다. CdS 박막은 전자빔 증착법(e-beam evaporation), 화학용액증착법(chemical bath deposition), 열분해법(spray pyrolysis), 스퍼터링법(sputtering) 등으로 제작되고 있다. 이 중 스퍼터링법의 경우, 다른 증착법에 비해 조작이 간단하고 넓은 면적에서 균일한 박막을 증착할 수 있을 뿐만 아니라, 박막두께 조절이 용이하다. 따라서 본 실험에서는 RF 마그네트론 스퍼터링법으로 증착된 CdS 박막의 기판온도 및 열처리 온도변화에 따른 구조적 및 광학적 특성을 조사하였다. 기판은 RCA 기법으로 세정된 Corning Eagle 2000 유리 기판을 사용하였다. 박막 공정은 초기 진공 $1{\times}10^{-6}Torr$ 상태에서 20 sccm의 Ar 가스를 주입하고 100 W의 RF 파워, 7 mTorr의 공정 압력에서 기판 온도를 $200^{\circ}C$부터 $500^{\circ}C$까지 변화시키면서 수행하였다. 증착된 CdS 박막은 질소 분위기의 가열로(furnace)를 이용해 $300-500^{\circ}C$ 온도에서 30분간 열처리되었다. 시료들의 표면 형상은 scanning electron microscope를 사용하여 관찰하였으며, UV-vis-NIR spectrophotometer를 사용하여 400-1,000 nm 파장영역에서의 투과율을 측정하였다. 그리고 X-선 회절분석(X-Ray Diffraction)으로 결정구조를 조사하고 결정립 크기를 산출하였다.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.8
• /
• pp.616-621
• /
• 2011

In this paper, CdS thin films, which were widely used window layer of the CdTe and the Cu(In,Ga)$Se_2$ thin film solar cell, were grown by chemical bath deposition, and effects of pH of reaction solution on the structural and optical properties were investigated. For pH<10.5, as the pH of reaction solution was higher, the deposition rate of CdS films was increased by improving ion-by-ion reaction in the substrate surface and the crystallinity of the films was improved. However, when the pH was higher than 10.5, the deposition rate was decreased because of smaller $Cd^{2+}$ ion concentration in the reaction solution. Also, the crystallinity of the films were deteriorated. The CdS films deposited at lower pH showed poor optical transmittance due to adsorbed colloidal particles, while the transmittance was improved for higher pH.