• Title/Summary/Keyword: $CuInS_{2}$

Search Result 2,281, Processing Time 0.031 seconds

Characteristics of the Number and the Mass Concentrations and the Elemental Compositions of PM10 in Jeju Area (제주지역 PM10의 수농도 및 질량농도와 원소성분 조성 특성)

  • Kang, Chang-Hee;Hu, Chul-Goo
    • Journal of Environmental Science International
    • /
    • v.23 no.3
    • /
    • pp.447-457
    • /
    • 2014
  • The number concentrations, the mass concentrations and the elemental concentrations of $PM_{10}$ have measured at Gosan site in Jeju, Korea, from March 2010 to December 2010. And the correlation and the factor analysis for the number, the mass and the elemental concentrations of $PM_{10}$ are performed to identify their relationships and sources. The average $PM_{10}$ number concentration is observed $246\;particles/cm^3$($35.7{\sim}1,017\;particles/cm^3$) and the average $PM_{10}$ mass concentration is shown $50.1{\mu}g/m^3$($16.7{\sim}441.4{\mu}g/m^3$) during this experimental period. The number concentrations are significantly decreased with increasing particle size, hence the concentrations for the smaller particles less than $2.5{\mu}m$($PM_{2.5}$) are contributed 99.6% to the total $PM_{10}$ number concentrations. The highest concentration of the 20 elements in $PM_{10}$ determined in this study is shown by S with a mean value of $1,497ng/m^3$ and the lowest concentration of them is found by Cd with a mean value of $0.57ng/m^3$. The elements in $PM_{10}$ are evidently classified into two group based on their concentrations: In group 1, including S>Na>Al>Fe>Ca>Mg>K, the elemental mean concentrations are higher than several hundred $ng/m^3$, on the other hand, the concentrations are lower than several ten $ng/m^3$ in group 2, including Zn>Mn>Ni>Ti>Cr>Co>Cu>Mo>Sr>Ba>V>Cd. The size-separated number concentrations are shown positively correlated with the mass concentrations in overall size ranges, although their correlation coefficients, which are monotonously increased or decreased with size range, are not high. The concentrations of the elements in group 1 are shown highly correlated with the mass concentrations, but the concentrations in group 2 are shown hardly correlated with the mass concentrations. The elements originated from natural sources have been predominantly related to the mass concentrations while the elements from anthropogenic sources have mainly affected on the number concentrations of $PM_{10}$.

Synthesis of Ultrafine LaAlO$_3$ Powders with Good Sinterability by Self-Sustaining Combustion Method Using (Glycine+Urea) Fuel ((Glycine+Urea) 혼합연료를 이요한 자발착화 연소반응법에 의한 우수한 소결성의 초미분체 LaAlO$_3$ 분말 합성)

  • Nam, H.D.;Choi, W.S.;Lee, B.H.;Park, S.
    • Journal of the Korean Ceramic Society
    • /
    • v.36 no.2
    • /
    • pp.203-209
    • /
    • 1999
  • LaAlO3d single phase used as the butter layer on Si wafer for YBa2Cu3O7-$\delta$ superconductor application were prepared by solid state reaction method and by self-sustaining combustion process. The microstructure and crystallity of synthesiszed LaAlO3 powder studied using scanning electron microscope (SEM) and X-ray diffractometer(XRD), specific surface area and sintering characteristics fo powder were investigated by Brunauer-Emmett-Teller (BET) method and dilatometer respectively. In solid state reaction method, it is difficult to obtain LaAlO3 single phase up to 150$0^{\circ}C$ period. However, in self-sustaining combustion process, it is to easy to do it only $650^{\circ}C$. Based on the results of analysis of dilatometer it is easier to obtain high sintering density (98.87%) in self-sustaining combustion process than in the solid state reaction method. This reason is that the average particle size prepared by self-sustaining combustion process is nano crystal size and has high specific surface are value(56.54 $m^2$/g) compared with that by solid state reaction method. Also, LaAlO3 layer on the Si wafer has been achieved by screen printing and sintering method. Even though the sintering temperature is 130$0^{\circ}C$, the phenomena of silicon out diffusion in LaAlO3/Si interphase are not observed.

  • PDF

Mossbauer Studies of the $H_2$ Reduction Effects On Magnetic Properties of Sr-Ba Substituted Hexgonal Ferrite (치환형 Sr-Ba 육방 페라이트들의 자기적 성질에 수소환원이 미치는 효과에 관한 Mossbauer 분광학적 연구)

  • 박재윤;권명회;이재광
    • Journal of the Korean Magnetics Society
    • /
    • v.9 no.1
    • /
    • pp.35-40
    • /
    • 1999
  • Sr substituted materials for some barium in M-type barium ferrite powder and Co-Ti substituted Sr-Ba hexagonal ferrite powder were prepared by citrate sol-gel method and 2 MOE sol-gel method these hexaferrite particles were reduced for 1hr in the hydrogen gas. The reduction temperatures were varied in the range of 250 $^{\circ}C$ to 500 $^{\circ}C$. X-ray diffraction patterns were measured using diffractometer with Cu $K_{\Alhpa}$ radiation. Mossbauer absorption spectra were measured with a constant acceleration spectrometer. We have focused on studying the origin of increasing $M_s$ by M$\"{o}$ssbauer spectroscopy. Ferrite particles which were sintered at 105$0^{\circ}C$ were found to be typical magnetoplumbite structure and single phase. XRD patterns with varying the reduction temperatures in $Sr_{0.5}Ba_{0.5}Fe_{10}O_{19}$ indicates ferrites particles become composite hexaferrites containing $\alpha$-Fe at T_{red}=350 \;$^{\circ}C$$. On the otherhand, it was found that $Co^{2+}$ ions and $Ti^{4+}$ ions in $Sr_{0.7}Ba_{0.3}Fe_{10}CoTiO_{19}$ prevent from changing $Fe^{3+}$ ions to $\alpha$-Fe during the $H_2$ reduction. Comparing Mossbauer results with XRD results, we have determined most of $\alpha$-Fe are reduced from $4f_{vi}$ sites and 12k sites of $Fe^{3+}$ ions. These $\alpha$-Fe phase bring the induced anisotropy and increase saturation magnetization $M_s$.TEX>.

  • PDF

Growth, Flowering, and Nutrient Composition of Salvia Grown in Peat moss Media Containing Pellets Processed with Poultry Feather Fibers at Different Mixing Ratios

  • Yoo, Yong Kwon;Kim, In Kyung;Roh, Mark S.;Roh, Yong Seung;Huda, Masud
    • Horticultural Science & Technology
    • /
    • v.35 no.3
    • /
    • pp.289-299
    • /
    • 2017
  • The objective of this study was to determine the effect of replacing perlite (PL) with pellets processed with poultry feather fiber as an inert material to prepare growing medium. The growth and flowering of Salvia splendens 'Vista Red' grown in individual growing medium $Biosangto^{(R)}$, peat moss (PM), PL, and two pellets (P45-1 and P45-2) were evaluated. Peat moss was mixed with PL, P45-1, or P45-2 at various ratios (1:0 to 1:3 or 3:1 by volume) to investigate the feasibility of replacing PL with pellets. Nutrient composition of the growing medium and leaf tissues was analyzed. The number of florets, inflorescence length, plant height, and fresh weight of plants grown in media containing P45-1 or P45-2 were reduced compared to those grown in individual growing medium PM or PL. As the mixing ratio of P45-1 or P45-2 to PM was higher, the growth of salvia, such as inflorescence length, plant height, number of leaves, and fresh weight was inhibited. Our results indicate that mixing three parts PM with one part of P45-1 (PM/P45-1/3:1) or P45-2 (PM/P45-2/3:1) accelerated flowering and increased the number of florets and leaves compared to other mixing ratios of PM and pellets media. The concentrations of phosphorus (P), calcium (Ca), boron (B), iron (Fe), and copper (Cu) in individual growing medium PL, P45-1, and P45-2 were significantly lower than those in PM. The concentration of N was the highest in leaves of plants grown in P45-1 or P45-2 amended media, and the concentrations of P, Ca, and zinc (Zn) in leaves were lower in individual growing medium P45-1 or P45-2 than in PM and PL. The pH of PM/P45-1/3:1 or PM/P45-2/3:1 media was maintained at optimal level (5.8-5.9) and the concentrations of macro- and micro-elements in the media and leaves were considered to be optimal levels. Therefore, mixing three parts PM with one part P45-1(PM:P45-1/3:1) or P45-2 (PM:P45-2/3:1) is recommended for improved growth and flowering in salvia. This suggests that P45-1 or P45-2 can replace PL as an inert material to prepare growing medium.

Poly-imide 기판에서 제조된 flexible CIGS 태양전지의 Mo strain 개선을 통한 효율 향상 연구

  • Myeong, A-Ron;Kim, Jae-Ung;Kim, Hye-Jin;Park, Se-Jin;Jeong, Chae-Hwan
    • Proceedings of the Korean Vacuum Society Conference
    • /
    • 2016.02a
    • /
    • pp.399.2-399.2
    • /
    • 2016
  • Cu(In,Ga)Se2 (CIGS) 박막 태양전지는 높은 효율과 낮은 제조비용, 높은 신뢰성으로 인해 박막 태양전지 중 가장 각광받고 있다. 특히 유리기판 대신 가볍고 유연한 철강소재나 플라스틱 소재를 이용하여 발전분야 외에 건물일체형, 수송용, 휴대용등 다양한 분야에 적용이 가능하다. 이러한 유연 기판을 이용한 CIGS 태양전지의 개발을 위해서는 기판의 특성에 따른 다양한 공정개발이 선행되어야 한다. Poly-imide와 같은 유연기판은 공정온도가 $400^{\circ}C$이하로 낮고 기판이 매우 얇아 기존 Mo 공정을 개선하여야한다. 이러한 유연기판의 특성을 고려하여 본 연구에서는 기존 bi-layer Mo의 bottom layer의 두께를 조절하여 박막의 strain을 조절하였다. 유연기판으로는 SKC KOLON에서 제조된 GL type의 기판을 사용하였다. 기판의 두께는 50um이다. 먼저 Mo의 bottom layer 두께 비율을 기존 12.5%에서 50%로 증가 시켰으며 전체 박막의 두께 역시 900nm에서 500nm로 두께를 감소시키며 실험을 실시하였다. 그 후 흡수층은 Co-Evaporation 방법을 이용하여 제조하였으며 이때 공정온도는 기존 공정온도에서 450, $400^{\circ}C$로 낮추어 흡수층을 제조하였다. 소자 제조 후 초기 Mo의 strain 개선과 저온공정이 적용되지 않은 경우 4.4%에서 공정 최적화 후 13%로 효율이 증가하였다. 제조된 흡수층은 SEM, XRF, XRD등을 이용하여 분석하였으며 그 외 일반적인 방법을 이용하여 Mo, CdS, TCO, Al grid를 제조하였다. AR 코팅은 제외 하였으며 제조된 소자는 솔라 시뮬레이터를 이용하여 효율 특성 분석을 실시하였으며 Q.E. 분석을 실시하였다.

  • PDF

Deposition of YBCO Films on Moving Substrate by a Spray Pyrolysis method (분무 열분해 CVD법으로 이동 중인 LaAlO_3(100) 단결정 위에 증착시킨 YBCO 박막의 특성)

  • Kim, Jae-Gun;Hong, Suk-Kwan;Kim, Ho-Jin;Yu, Seok-Koo;Cho, Han-Woo;Ahn, Jin-Hyun;Joo, Jin-Hoo;Lee, Hee-Gyoun;Hong, Gye-Won
    • Progress in Superconductivity
    • /
    • v.8 no.1
    • /
    • pp.93-97
    • /
    • 2006
  • YBCO films were deposited on a moving substrate by a spray pyrolysis method using nitrate aqueous solution as precursors. Deposition was made on $LaAlO_3$(100) single crystal substrate by spraying precursor droplets generated by a concentric nozzle. The cation ratio of precursor solution was Y:Ba:Cu=1:2.65:4.5. The distance between nozzle and substrate was 15 cm. Substrate was transported with a speed ranging from 0.23 cm/min to 0.5 cm/min. Films were deposited at the pressure ranging from 10 Torr to 20 Torr and the deposition temperature was ranged from $740^{\circ}C\;to\;790^{\circ}C$. Oxygen partial pressure was controlled between 1 Tow and S Torr. Superconducting YBCO films were obtained from $740^{\circ}C\;to\;790^{\circ}C$ with an oxygen partial pressure of 3 Torr. Scanning electron microscope(SEM) and X-ray diffraction(XRD) observation revealed that films are smooth and highly texture with(001) plans parallel to substrate plane. Highest Jc was 0.72 $MA/cm^2$ at 77K and self-field for the film with a thickness of 0.15 m prepared at a substrate temperature of $740^{\circ}C$ and $PO_2$=3 Torr.

  • PDF

Component(mineral) difference of Phellinus linteus on cultured to timber (기주식물에 따른 목질진흙버섯의 일반성분(무기물) 함량변화 I)

  • Lee, Soo-Won;Han, Ki-Won;Jang, Won-Cheoul;Lee, Dae-Jin;Jung, Dong-Sik;Lee, Byung-Eui
    • Journal of Mushroom
    • /
    • v.3 no.3
    • /
    • pp.100-104
    • /
    • 2005
  • We investigated mineral difference from mushroom Phellinus linteus and Phellinus baumii on mulberry, oak and elm. ICP test, The major mineral components were K, Ca, and Fe, while Mg, Na, P, Cr, Mn, Cu and Zn were determined as micro mineral components. In case of P.linetus and P.baumii the component of K was shown as 699.0mg/100g and 630mg/100g, in oak, 340.7mg/100g and 314.6mg/100g in elm, and 311.6mg/100g and 311.6mg/100g in mulberry respectively. In Ca, mulberry fruiting body were shown about 2 times highest and expecially in case of Na was oak fruiting body were shown as 10 times highest as against the others sample groups. In micro mineral components, Zn component was shown very diffeence about sample groups. We concluded that the highest mineral component of K was shown in mushroom cultivated on oak of both P.linetus and P.baumii. As a results, mineral component has showed very difference on cultivated to timber. According to the results of mineral component we concluded that Phellinus linteus and Phellinus baumii has mineral component different depending on timber.

  • PDF

The Transition of Production, Consumption and Price of Non-ferrous Metals (비철금속(非鐵金屬)의 생산(生産), 소비(消費), 시세(時勢)의 추이(推移))

  • Moon, W.J.
    • Economic and Environmental Geology
    • /
    • v.2 no.3
    • /
    • pp.1-25
    • /
    • 1969
  • In considering the mining industry, it is necessary to study the production, consumption and price of ore and metals in every country of the world in order to determine the trend of the industry in the present and for the future. This study is necessary especially for exporting domestically produced are which is in excess of domestic consumption and for importing are, or metal where local production does not meet domestic demand. It will be treated of Au, Ag, Cu, Pb, Zn, W, Mo, which are the most important non-ferrous metals, and which greatly affect the mining industry of Korea. The presentation will concern itself only with the free world. About 1, 200 ton of gold are produced annually with little fluctiation in recent years. Most of the gold produced is consumed by advanced countries for industrial uses as well as for producing precious objects. The U.S.A. expends yearly about four times its domestic production and Japan about three times its domestic production for industry and arts. Because of the instability of the currency of the U.S.A., England and France, recently, the price of gold has been $ 41-42 per ounce, whereas the official price is $35.00 per ounce. It will be expected that the official price will be raised in the near future. As for silver, about 6,500 tons are produced annually with no special fluctuation change in recent years. However, the annual consumption is about 14,000 ton, so the supply and demand is extremely unbalanced. The shortage is made up by the sale of the U.S. treasury's reserve stock and the reclaiminig of silver from coins and other scrap. As the Treasury'S reserves will be exhausted in a year or two, the price of silver which is $1. 64 per ounce, will go up drastically in about a year. As for copper, 5,257,000 ton's were mined in 1966. It's production is being increased about 5% annually. However, consumption exceeds production by about 100,000 ton a year. The recent Foreign refinery copper price in the U.S.A is $ 60 per pound. The supply of copper being insufficient to meet international demands, the price will go up and with no prospect of being lowered in the near future even with the slight annual increase in production. About 2,100,000 to 2,200,000 tons of lead are produced annually. Consumption exceeds production by about 50,000-60,000 tons annually. The current price of lead in New York is $ 155 per pound. As the supply of lead is internationally stable, It will be believed that there will be no significant change in its price in the near future. In 1967, 3,926,000 tons of Zinc were produced. There is annual increase of 4-7% in production. The annual consumption exceeds production by 100,000 to 200,000 tons. The current zinc price in the St. Louis market inthe U.S.A. is $ 145 per pound. Even though its supply is stable and sufficient world wide, the consumption rate will increase at a faster pace than before; hence, the price will slowly go up. Tungsten mines yield about 11,000 tons a year. Its production has been relatively constant in the past few years. The amount of its consumption increases slowly world wide, but in the free world· there has been a slight annual decrease. However, since Red China has not been exporting their tungsten to other countries for several months, the price on the London market of S.T.U. of $Wo_3$ has increased to $ 44~46. Should Red China begin to export actively again the price will drop to $ 40~42. In 1967, 56,000 tons of Molybdenum were produced. Production exceeds consumption by 200,000 -30,000 tons annually. The current price in the U.S.A. is $ 1.72 per Mo pound. Since the rate of production in the U.S.A. is on the increase with large amounts of ore reserve, the price of molubdenum should not go up.

  • PDF

Characteristics of Lactate Dehydrogenase Produced from Lactobacillus sp. FFy111-1 as a Ruminant Probiotic (반추동물용 활성제로서 Lactobacillus sp. FFy111-1이 생산한 Lactate Dehydrogenase의 특성에 관한 연구)

  • Sung, H.G.;Kim, D.K.;Bae, H.D.;Shin, H.T
    • Journal of Animal Science and Technology
    • /
    • v.46 no.4
    • /
    • pp.625-634
    • /
    • 2004
  • The objective of this experiment is to study the possibility of lactate dehydrogenase(LDH) enzyme to prevent lactate accumulation in the rumen, For understanding capacity of bacterial LDH in rumen environments, this study was conducted to explore the effects of temperature, pH, VFAs and metal ions on Lactobacillus sp. FFy111-1's LDH activity, and the LDH activation in rumen fluid accumulated lactate. The optimum pH and temperature of LDH were pH 7.5 and 40$^{\circ}C$, respectively. The LDH activity had a good thennostability at range from 30 to 50$^{\circ}C$. The highest pH stability of the enzyme was at ranges from pH 7.0 to 8.0 and the enzyme activities showed above 64% level of non-treated one at pH 6.0 and 6.5. The LDH was inactivated by VFAs treatments but was enhanced by metal ion treatments without NaCl and $CuSO_4$ Especially, the LDH activity was increased to 127% and 124% of its original activity by 2 mM of $BaCl_2$ and $MnSO_4$, addition, respectively. When the acidic rumen fluid was treated by LDH enzyme of Lactobacillus sp. FFy111-1, the lactate concentration in the rumen fluid was lower compared with non-treated rumen fluid(P<0.05). This lactate reduction was resulted from an action of LDH. It was proved by result of purified D,L-LDH addition that showed the lowest lactate concentration among the treatments(P<0.05). Although further investigation of microbial LDH and ruminal lactate is needed, these findings suggest that the bacterial LDH has the potential capability to decrease the lactate accumulated in an acidic rumen fluid. Also, screening of super LDH producing bacteria and technical development for improving enzyme activity in rumen environment are essential keys for practical application.

Oxidative Stress Inhibitory Effects of Low Temperature-Aged Garlic (Allium sativum L.) Extracts through Free Radical Scavenging Activity (저온숙성마늘의 라디칼 소거 활성을 통한 산화스트레스 억제 효과)

  • Hwang, Kyung-A;Kim, Ga Ram;Hwang, Yu-Jin;Hwang, In-Guk;Song, Jin
    • Journal of the Korean Society of Food Science and Nutrition
    • /
    • v.45 no.1
    • /
    • pp.27-34
    • /
    • 2016
  • Garlic has drawn attention as a food material for its anti-oxidative and anti-inflammatory properties as well as for prevention and treatment of cancer. In order to increase efficiency, various aging methods for garlic have been attempted. In particular, thermally processed garlic is known to have higher biological activities due to its various chemical changes during heat treatment. Therefore, in this study, we investigated the anti-oxidative effects of garlic extracts aged at low temperature ($60{\sim}70^{\circ}C$). In the results, 2,2-diphenyl-1-picrylhydrazyl and 2,2-azino-bis (3-ethylbenzo-thiazoline-6-sulfonate) radical scavenging activities and ferric reducing ability of low temperature-aged garlic (LTAG) were similar to those of raw garlic. LTAG also showed decreased lipopolysaccharide (LPS)-induced production of reactive oxygen species, although there were not significant differences among samples. In addition, xanthine oxidase activity was inhibited by LTAG; the 15 days and $60^{\circ}C$ extract showed outstanding inhibition compared with the others. To understand the molecular mechanisms behind the anti-oxidative activity of LTAG, we performed quantitative real-time PCR analysis. The 30 days and $70^{\circ}C$ extract upregulated mRNA expression of antioxidant enzymes such as Cu/Zn-superoxide dismutase (SOD), Mn-SOD, glutathione peroxidase, and catalase in LPS-stimulated RAW 264.7 cells. This result indicates that LTAG can be a functional food as a nature antioxidant and antioxidant substance.