• 한국분말재료학회지
• /
• 제6권4호
• /
• pp.301-306
• /
• 1999

Mechanical properties of oxide based materials could be improved by nanocomposite processing. To investigate optimum route for fabrication of nanocomposite enabling mass production, high energy ball milling and Pulse Electric Current Sintering (PECS) were adopted. By high energy ball milling, the $Al_2O_3$-based composite powder with dispersed Cu grains below 20 nm in diameter was successfully synthesized. The PECS method as a new process for powder densification has merits of improved sinterability and short sintering time at lower temperature than conventional sintering process. The relative densities of the $Al_2O_3$-5vol%Cu composites sintered at $1250^{\circ}C$ and $1300^{\circ}C$ with holding temperature of $900^{\circ}C$ were 95.4% and 95.7% respectively. Microstructures revealed that the composite consisted of the homogeneous and very fine grains of $Al_2O_3$ and Cu with diameters less than 40 nm and 20 nm respectively The composite exhibited enhanced toughness compared with monolithic $Al_2O_3$. The influence of the Cu content upon fracture toughness was discussed in terms of microstructural characteristics.

• 한국자기학회지
• /
• 제18권1호
• /
• pp.43-47
• /
• 2008

[ $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ ] nano-glass를 sol-gel 법으로 제조 하였다. 평균 입자 크기는 60.3 nm였으며 매우 균일한 입도 분포를 가졌다. Nano-glass를 NiZnCu ferrite의 저온소성용 소결조제로 사용하였으며 NiZnCu ferrite에 nano-glass를 첨가한 후 $840{\sim}900^{\circ}C$에서 2시간 소결을 진행하였다. 소결성 및 자기적 특성에 대해 연구하였으며 밀도, 수축율, 초투자율, 품질계수, 및 포 화자화값을 측정하였다. nano-glass를 0.5 wt% 첨가하여 $900^{\circ}C$에서 소결한 토로이달 core 시편의 초투자율은 1 MHz에서 측정 시 193.3의 값을 가졌다. 초투자율과 포화자화값은 소결온도가 증가함에 따라 증가하는 경향을 나타내었다. sol-gel 법에 의해 제조된 $ZnO-Bi_2O_3-Al_2O_3-B_2O_3-SiO_2$ nano-glass를 칩인덕터용 NiZnCu ferrite의 저온 소결조제로 사용 가능함을 알 수 있었다.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2000년도 추계학술대회 및 발표대회 강연 및 발표논문 초록집
• /
• pp.20-20
• /
• 2000

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2002년도 춘계학술강연 및 발표대회
• /
• pp.10-10
• /
• 2002

• 자원리싸이클링
• /
• 제23권1호
• /
• pp.33-39
• /
• 2014

본 연구에서는 폐 PCB의 주성분인 Cu와 $CaO-SiO_2-Al_2O_3-MgO$계 슬래그의 평형실험에 의해 Cu의 용해도에 대하여 조사하였다. 1673 K~1825 K 범위에서 일정한 비율로 미리 용융된 4원계 슬래그와 Cu를 흑연 도가니에 각각 20 g 장입한 후, 10시간동안 평형 을 유지하였다. 분위기 중의 산소분압은 CO가스와 Ar가스의 비율을 조절하여 $10^{-17.23}{\sim}10^{-15.83}$ atm 범위로 제어하였다. 평형산소 분압과 염기도 및 MgO 농도가 증가할수록 슬래그 중 Cu의 농도는 증가하였다. 그리고 반응 온도가 높을수록 슬래그 중의 Cu의 농도는 감소하였다. 슬래그 중으로 용해되는 Cu의 반응은 발열반응이다.

• 대한금속재료학회지
• /
• 제47권11호
• /
• pp.754-758
• /
• 2009

Dense $5Cu_{0.6}Fe_{0.4}-Al_{2}O_{3}$ composite was consolidated from mechanically synthesized powders by high frequency induction heating method within 2 min. Consolidation was accomplished under the combined effects of a induced current and mechanical pressure. Dense $5Cu_{0.6}Fe_{0.4}-Al_{2}O_{3}$ with relative density of up to 95% was produced under simultaneous application of a 80 MPa pressure and the pulsed current. Fracture toughness and hardness of the composite are $7.6MPa{\cdot}m^{1/2}$ and $844kg/mm^{2}$ respectively.

• 한국대기환경학회지
• /
• 제23권1호
• /
• pp.64-73
• /
• 2007

The catalytic activity of transition metals (Cu, Co, Mn, Fe and Ni) supported on ${\gamma}-Al_2O_3$ for the oxidation of toluene was investigated in the microreactor of fixed-bed type. The catalytic activity of transition metals for the oxidation of toluene turned out to be increasing in the order of Ni$Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene increased with the increasing loadings of copper, reached the maximum activity at 5% loadings of copper, and decreased with higher loadings of copper in the catalysts. The activity of $Cu/{\gamma}-Al_2O_3$ catalysts for the oxidation of toluene decreased with the increasing calcination temperatures. This might result from the decreasing surface area of catalysts due to the sintering of copper oxide as well as ${\gamma}-Al_2O_3$ supports. The 5wt% $Cu/{\gamma}-Al_2O_3$ catalysts calcined at $400^{\circ}C$ for 4 hrs in the air showed the highest activity for the oxidation of toluene. Mutual inhibition was observed for the binary mixture of toluene and xylene. The activity of the easy-to-oxidize toluene was greatly decreased while the difficult-to-oxidize xylene was slightly decreased in the binary mixture of toluene and xylene. It might suggest that the inhibition of toluene and xylene in the binary mixture resulted from the competitive adsorption for the adsorbed oxygen on the catalytic surface.

• 한국수소및신에너지학회논문집
• /
• 제19권1호
• /
• pp.71-76
• /
• 2008

CuFeOx/$Al_2O_3$ catalysts are developed for the use in sulfuric acid decomposition which is a subcycle in thermochemical iodine-sulfur cycle to split water into hydrogen and oxygen. Both Cu and Fe components are co-precipitated with Al component to enhance distribution of active components. Developed catalysts are improved in the capability of sulfuric acid decomposition and endurance under highly acidic environment compared to commercial catalysts such as Pt/$Al_2O_3$ and $2CuO{\cdot}Cr_2O_3$. Developed CuFeAlOx catalysts exhibited higher sulfuric acid decomposition ability than $2CuO{\cdot}Cr_2O_3$ and longer endurance trends than Pt/$Al_2O_3$ maintaining comparable performance, respectively.

• Progress in Superconductivity
• /
• 제2권2호
• /
• pp.71-75
• /
• 2001

The effect of annealing step-edges of LaAlO$_3$ and MgO single crystal substrates on YBa$_2$Cu$_3$O$_{7}$ junction has been studied. The step-edge was fabricated by argon ion milling and was annealed at 105$0^{\circ}C$ in 1 attn oxygen pressure. We compared AFM image near step-edge of the substrates between before and after annealing process. And YBa$_2$Cu$_3$O$_{7}$ thin film was deposited on the step-edge by a standard pulsed laser deposition. The step-edge junctions were characterized by current-voltage curves at 77 K. The annealing of step-edges of MgO substrate improved the current-voltage characteristic of Josephson junction: double steps in the current-voltage characteristic disappeared. However the annealing for LaAlO$_3$ did not improve the junction property.rty.

• 한국분말재료학회지
• /
• 제14권2호
• /
• pp.123-126
• /
• 2007

In this work, the dispersion behavior of $Y_2O_3$ particles in binary aluminum (Al)-copper (Cu) cast alloy was investigated with respect to Cu contents of 20 (hypoeutertic), 33 (eutectic) and 40 (hypereutectic) wt.%. In cases of hypo and hypereutectic compositions, SEM images revealed that the primary Al and ${\theta}$ phases were grown up at the beginning, respectively, and thereafter the eutectic phase was solidified. In addition, it was found that some of $Y_2O_3$ particles can be dispersed into the primary Al phase, but none of them are is observed inside the primary 6 phase. This different dispersion behavior of $Y_2O_3$ particles is probably due to the difference in the val- ues of specific gravity between $Y_2O_3$ particles and primary phases. At eutectic composition, $Y_2O_3$ particles were well dispersed in the matrix since there is few primary phases acting as an impediment site for particle dispersion during solidification. Based on the experimental results, it is concluded that $Y_2O_3$ particles are mostly dispersed into the eutectic phase in binary Al-Cu alloy system.