• Journal of the Korean Ceramic Society
• /
• v.43 no.1 s.284
• /
• pp.10-15
• /
• 2006

Photoluminescence (PL) and crystal structures of the $(l-x)CaWO_4-xLi_2WO_4$ binary system added with $Eu_2O_3$ activator have been characterized. The $CaWO_4\;and\;Li_2WO_4$ have the scheelite and phenakite structures respectively. The $CaWO_4-Li_2WO_4-Eu_2O_3$ phosphors show the red luminescence of 613 nm peak wavelength. The wavelength range of excitation spectral band is $380\~470$ nm with the peak wavelength of 397 nm. The $0.88(0.5CaWO_4-0.5Li_2WO_4)-0.12Eu_2O_3$ showed the most superior luminescence characteristics. The effect of co-doping elements such as $Al_2O_3$ and rare-earth oxides on PL has been characterized. The co-doping elements deteriorated the luminescence intensity except the $Al_2O_3$ and $Gd_2O_3$. The PL characteristics of $CaWO_4-Li_2WO_4-Eu_2O_3$ phosphors have been compared to those of the alkali europium double molybdates (tungstates) of scheelite-related structure such as $LiEu(MoO_4)_2$ and $CsEu(MoO_4)_2$. The crystal structures of $(l-y)[(l-x)CaWO_4-xLi_2WO_4]-yEu_2O_3$ phosphors have been characterized using XRD data and rietveld refinement.

• Resources Recycling
• /
• v.31 no.4
• /
• pp.19-25
• /
• 2022

In this study, tungsten carbide (WC) powder was prepared using a novel recycling process for hard metal sludge that does not use ammonium paratungstate. Instead of ammonia, acid was used to remove the sodium and crystallized tungstate, resulting in the formation of tungstic acid (H₂WO₄). The WC powder was successfully synthesized by the carbothermal reduction of tungstic acid through H₂O decomposition, reduction of WO₃ to W, and formation of WC. The carbon content and holding time at the carbothermal reduction temperature were optimized to remove free carbon from the WC powder. As a result, most of the free carbon in the WC powder prepared from sludge was removed, and the content of free carbon in the synthesized WC powder was lower than that in commercial WC powder. Moreover, the crystallite size of WC prepared from H₂WO₄ was much smaller than that of commercial micron-sized WC powder produced from APT. The small crystallite size of WC induces grain growth during the sintering of the WC-Co composite; thus, a WC-Co composite with large WC grains was fabricated using the WC powder prepared from H₂WO₄. The large WC grains affected the mechanical properties of the WC-Co composite. Further, due to the large grain size, the WC-Co composite fabricated from H₂WO₄ exhibited a higher toughness than that of the WC-Co composite prepared from commercial WC powder.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.401-404
• /
• 1997

We prepared 0~20mo1% WO$_3$added ZnO composite ceramics in order to promote a CO gas sensitivity. Using SE,. we observed the microstructure of sample. The resistances of sample were measured by High Voltage Measure/source Unit in the temperature range of +5V~-5V. The measured 1000ppm CO sensitivities of pure ZnO were about 1~4.3, and the measured 1000ppm CO sensitivities of ZnO-WO$_3$composite ceramics were about 1~8.2. Therefore, the 1000ppm CO sensitivities of ZnO-WO$_3$composite ceramics were about 2 times larger than that of pure ZnO.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.23 no.3
• /
• pp.142-145
• /
• 2013

The upconversion (UC) luminescence of $Li^+/Er^{3+}/Yb^{3+}$ co-doped $CaWO_4$ phosphors and effects of $Yb^{3+}$ concentration are investigated in detail. Single crystallized $CaWO_4$ : $Li^+/Er^{3+}/Yb^{3+}$ phosphor can be obtained, co-doped up to 35.0/5.0/30.0 mol% ($Li^+/Er^{3+}/Yb^{3+}$) by solid-state reaction. Under 980 nm excitation, $CaWO_4$ : $Li^+/Er^{3+}/Yb^{3+}$ phosphor exhibited strong green UC emissions visible to the naked eye at 530 and 550 nm induced by the intra 4f transitions of $Er^{3+}$ ($^4H_{11/2}$, $^4S_{3/2}{\rightarrow}^4I_{15/2}$). The optimum doping concentrations of $Yb^{3+}$ that would result in the highest UC luminescence were determined, and a possible UC mechanism that depends on the pumping power is discussed in detail.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.193-198
• /
• 2008

$WO_3$-doped $SnO_2$ thin films were prepared in a solution-deposition method and their gas-sensing characteristics were investigated. The doping of $WO_3$ to $SnO_2$ increased the response ($R_a/R_g,\;R_a$: resistance in air, $R_g$: resistance in gas) to $H_2$ substantially. Moreover, the $R_a/R_g$ value of 10 ppm CO increased to 5.65, whereas that of $NO_2$ did not change by a significant amount. The enhanced response to $H_2$ and the selective detection of CO in the presence of $NO_2$ were explained in relation to the change in the surface reaction by the addition of $WO_3$. The $WO_3$-doped $SnO_2$ sensor can be used with the application of a $H_2$ sensor for vehicles that utilize fuel cells and as an air quality sensor to detect CO-containing exhaust gases emitted from gasoline engines.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.9
• /
• pp.1621-1625
• /
• 2010

Recently, due to increase in the usage of toxic gas and inflammability gas, the ability to monitor and precisely measurement of these gases is crucial in preventing the occurrence of various accidents. CuO doped and undoped $WO_3$ thick films gas sensors were prepared using screen-printing method on alumina substrates. A structural properties of $WO_3$:CuO thick films had monoclinic phase and triclinic phase of $WO_3$ together. Sensitivity of $WO_3$:CuO sensor at 2000 ppm of $CO_2$ gas and 50 ppm of $H_2S$ gas was investigated. 4 wt% Cu doped $WO_3$ thick films had the highest sensitivity of $CO_2$ gas and $H_2S$ gas.

• Transactions of Materials Processing
• /
• v.24 no.4
• /
• pp.287-292
• /
• 2015

The possibility of chemical precipitation for recycled ammonium paratungstate (APT) was studied. WO₃ particles were synthesized by chemical precipitation method using a 1:2 weight ratio of APT:DI-water. At the 500℃ sintering temperature, the X-ray diffraction results showed that APT completely decomposed to WO₃. For the granulated powder WC-Co, vacuum heat treatment at proper temperatures increases tap density and flow-ability. Hardness of the WC-Co thermal spray coating layer was measured in the range HV 831~1266. Spray conditions for the best characteristic values were an oxygen flow rate=1500 scfh, a fuel flow rate = 5.25gph and a gun distance = 320mm.

• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.237-243
• /
• 1999

스크린 프린팅법을 이용하여 NOX 감지용 WO3 후막형 가스센서를 제조하였다. 본 실험에서는 감지막의 소성 온도에따른 감도변화 및 Ru을 첨가함으로써 감도의 증진을 중점적으로 조사하였다. 또한 NO2 50 ppm하에서 CO, H2, CH4 그리고 i-C4H10등의 가스에 대하여 cross sensitivity를 조사하였다. WO3 가스센서는 소성온도 50$0^{\circ}C$, 작동온도 30$0^{\circ}C$에서 최대감도를 얻었다. 순수한 WO3에 Ru(0.004 wt%)을 첨가시 NO2 및 NO 가스에 대한 감도가 크게 증진되었다. 그러나 순수한 WO3 센서는 Ru(0.004 wt%)이 첨가된 WO3 센서보다 더 우수한 cross sensitivity를 보였다.

• Korean Journal of Materials Research
• /
• v.11 no.11
• /
• pp.953-959
• /
• 2001

Homogeneous spherical W-Co salt powders were made by spray drying of aqueous solution of ammonium $metatungstate(NH_4)_6(H_2W_{12}O_{40}){\cdot}4H_2O,\; AMT)$ and cobalt nitrate $hexahydrate(Co(NO_3)_2{\cdot}6H_2O)$. The thermal decomposition process of spray dried W-Co salt powders was studied by TG, XRD, SEM, TEM and FT-IR. Spray dried W-Co salt powders were calcined for 1 hour in the temperature from$ 350^{\circ}C$ to $800^{\circ}C$ in atmosphere of air. At the temperatures over $600^{\circ}C$, spherical $CoWO_4/WO_3$ composite oxide powders were obtained. The primary particle size of W/Co composite oxide powders increased with increasing thermal decomposition temperature due to the particle growth. The observed crystallite size by TEM was in the range of 60nm and that of $CoWO_4$ calculated by Scherrer's formula at $800^{\circ}C$ was smaller than 55nm. The crystallite site was identified by XRD and TEM.

• Journal of the Korean Chemical Society
• /
• v.10 no.1
• /
• pp.32-42
• /
• 1966

The electrolysis of tungstic oxide dissolved in the bath of calcium chloride and calcium oxide was studied to produce metallic tungsten using carbon as anode and iron as cathode in the temperature range of 900^{\circ}$ to $1200^{\circ}C$. The binary phase diagrams $CaCl_2$-CaO and $CaCl_2-CaWO_4$ systems were constructed to determine the suitability of bath composition and the range of temperatures for the electrolysis. As $WO_3$ reacted with $CaCl_2$ to form oxychloride in the fused salt, the addition of the proper amount of CaO was necessary to avoid the loss of $WO_3$. The optimum compositions of fused bath were $CaCl_2$ 100 parts, CaO and $WO_3$ each 10 to 20 parts, with the CaO, $WO_3$ ratio greater than unity, to keep freezing point low and to prevent the vaporization of $CaCl_2$. The observed decomposition voltage at which $WO_3$ decomposes to W and CO was-0.1 volt, whereas the calculated was -0.3 volt. Metallic tungsten deposited at the cathode reacted easily with CO formed secondarily at the anode surface, to form WC below $1050^{\circ}C$, so that the cell temperature should be above $1050^{\circ}C$. The effects of cathode current densities on current efficiency were minor in the range of 1 to 5 $amp/cm^2$.