• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.400-403
• /
• 2003

Etching characteristics of (Pb,Sr)$TiO_3$(PST) thin films were investigated using inductively coupled chlorine based plasma system as functions of gas mixing ratio, RF power and DC bias voltage. It was found that increasing of Ar content in gas mixture lead to sufficient increasing of etch rate and selectivity of PST to Pt. The maximum etch rate of PST film is $562\;{\AA}$/min and the selectivity of PST film to Pt is 0.8 at $Cl_2/(Cl_2+Ar)$ of 20 %. It was proposed that sputter etching is dominant etching mechanism while the contribution of chemical reaction is relatively low due to low volatility of etching products.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.10
• /
• pp.846-851
• /
• 2007

In this work, the etching characteristics of $Ge_2Sb_2Te_5(GST)$ thin films were investigated using an inductively coupled plasma (ICP) of $Cl_2/Ar$ gas mixture. To analyze the etching mechanism, an optical emission spectroscopy (OES) and surface analysis using X-ray photoelectron spectroscopy (XPS) were carried out. The etch rate of the GST films decreased with decreasing Ar fraction. At the same time, high selective etch rate over $SiO_2$ films was obtained and the selectivity over photoresist films decreased with increasing the he fraction. From XPS results, we found that Te halides were formed at the etching surface and Te halides limited the etch rate of the GST films.

• Transactions on Electrical and Electronic Materials
• /
• v.12 no.2
• /
• pp.51-55
• /
• 2011

We investigated the etching characteristics of zinc oxide (ZnO) thin films deposited by the atomic layer deposition method. The gases of the inductively coupled plasma chemistry consisted of $Cl_2$, Ar, and $O_2$. The maximum etch rate was 40.3 nm/min at a gas flow ratio of $Cl_2$/Ar=15:5 sccm, radio-frequency power of 600 W, bias power of 200 W, and process pressure of 2 Pa. We also investigated the plasma induced damage in the etched ZnO thin films using X-ray diffraction (XRD), atomic force microscopy and photoluminescence (PL). A highly oriented (100) peak was present in the XRD spectroscopy of the ZnO samples. The full width at half maximum value of the ZnO sample etched using the $O_2/Cl_2$/Ar chemistry was higher than that of the as-deposited sample. The roughness of the ZnO thin films increased from 1.91 nm to 2.45 nm after etching in the $O_2/Cl_2$/Ar plasma chemistry. Also, we obtained a strong band edge emission at 380 nm. The intensities of the peaks in the PL spectra from the samples etched in all of the chemistries were increased. However, there was no deep level emission.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.14 no.10
• /
• pp.785-791
• /
• 2001

High dielectric (Ba, Sr) TiO$_3$ thin films were etched in an inductively coupled plasma (ICP) as a function of Cl$_2$/Ar mixing ration. Under Cl$_2$(20)/Ar(80), the maximum etch rate of the BST films was 400 $\AA$/mim and selectivities of BST to Pt and PR were obtained 0.4 and 0.2, respectively. Etching products were redeposited on the surface of BST and resulted in varying the nature of crystallinity. Therefore, we investigated the etched surface of BST by x-ray photoelectron spectroscopy (XPS) atomic force microscopy (AFM) and x-ray diffraction (XRD). From the result of XPS analysis, we found that residues of Ba-Cl and Ti-Cl bonds remained on the surface of the etched BST for high boiling point. The morphology of the etched surfact was analyzed by AFM. A smoothsurface(roughness ~2.8nm) ws observed under Cl$_2$(20)/Ar(80), rf power of 600 W, dc bias voltage of -250 V and pressure of 10 mTorr. This changed the nature of the crystallinity of BST. From the result of XRD analysis, the crystallinities of the etched BST film under Ar only and Cl$_2$(20)/Ar(80) were maintained as similar to as-deposited BST. However, intensity of BST(100) orientation under Cl$_2$ only plasma was abruptly decreased. This indicated that CI compounds were redeposited on the etched BST surface and resulted in changed of the crystallinity of BST during the etch process.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2008.11a
• /
• pp.41-42
• /
• 2008

본 논문에서는 As-doped ZnO 박막의 플라즈마 식각 특성 및 메커니즘에 관하여 실험을 수행 하였다. As-doped ZnO 박막 식각 실험은 유도 결합 플라즈마 식각 장비(inductively coupled plasma;ICP)와 $BCl_3$/Ar 플라즈마에 첨가된 $Cl_2$가스의 비, RF 전력, DC bias voltage, 공정 압력에 대한 식각 속도의 변화를 관찰 하였다. $BCl_3$/Ar 플라즈마에 $Cl_2$ 가스 첨가량 6 sccm 까지는 증가하지만 그 이후 $Cl_2$ 가스의 첨가량이 증가할 때 식각속도가 감소하였다. 이는 플라즈마 내에서 Cl 라디칼의 밀도가 증가함에 따라서 $Ar^+$의 에너지가 감소와 비휘발성 식각 부산물의 증가에 의하여 효과적인 물리적 식각이 이루어 지지 못한 것으로 판단된다. OES를 이용하여 플라즈마 내에서 라디칼들의 빛의 세기를 측정하였고, 식각 후 As-type ZnO 박막 표면에서의 화학적 결합을 보기위해 XPS 분석을 실행하였다.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1438-1439
• /
• 2006

$Ge_{2}Sb_{2}Te_5$(GST) thin film at present is a promising candidate for a phase change random access memory (PCRAM) based on the difference in resistivity between the crystalline and amorphous phase. PCRAM is an easy to manufacture, low cost storage technology with a high storage density. Therefore today several major chip in manufacturers are investigating this data storage technique. Recently, A. Pirovano et al. showed that PCRAM can be safely scaled down to the 65 nm technology node. G. T Jeonget al. suggested that physical limit of PRAM scaling will be around 10 nm node. Etching process of GST thin ra films below 100 nm range becomes more challenging. However, not much information is available in this area. In this work, we report on a parametric study of ICP etching of GST thin films in $Cl_2$/Ar chemistry. The etching characteristics of $Ge_{2}Sb_{2}Te_5$ thin films were investigated using an inductively coupled plasma (ICP) of $Cl_2$/Ar gas mixture. The etch rate of the GST films increased with increasing $Cl_2$ flow rate, source and bias powers, and pressure. The selectivity of GST over the $SiO_2$ films was higher than 10:1. X-ray photoelectron spectroscopy(XPS) was performed to examine the chemical species present in the etched surface of GST thin films. XPS results showed that the etch rate-determining element among the Ge, Sb, and Te was Te in the $Cl_2$/Ar plasma.

• Journal of the Microelectronics and Packaging Society
• /
• v.9 no.2
• /
• pp.27-31
• /
• 2002

In this study, $CeO_2$ thin films were etched with an addition of $Cl_2$ gas to $Ar/CF_4$ gas mixing in an inductively coupled plasma (ICP) etcher by the etching parameter such as RF power of 700 W, chamber pressure of 15 mTorr and dc bias voltage of -200 volts. The etch rate of $CeO_2$ films was 250 $\AA$/min with an addition of 10% $Cl_2$ gas to $Ar/CF_4$ gas mixture and the selectivity to SBT film was 0.4 at that condition. The surface reactions of the etched $CeO_2$ thin films were investigated by X-ray photoelectron spectroscopy (XPS). It was analyzed that Ce peaks were mainly observed in Ce-O bonds formed $CeO_2$ or $Ce_2O_3$ compounds. Cl peaks were detected by the peaks of Cl $2p_{3/2}$ and Cl $2p_{1/2}$. Almost all of Cl atoms were combined with Ce atoms like $CeCl_x$ or $Ce_x/O_yCl_z$ compounds.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.11a
• /
• pp.177-178
• /
• 2007

본 연구에서는 MIM (Metal-Insulator-Metal) capacitor의 유전 물질로 사용되는 $Ba_xTi_yO_z$(BTO) 박막의 식각 특성을 고찰하였다. $Cl_2$/Ar 혼합가스를 이용하여 Inductively Coupled Plasma(ICP)에서 BTO 박막을 식각하였고, 식각된 BTO박막의 표면을 X-ray photoelectron spectroscopy(XPS) 분석하였다. BTO박막의 식각 속도는 Ar이 80%인 식각 조건에서 31.7nm/min의 식각 속도를 추출하였고, 동시에 Pt박막에 대한 높은 선택비를 얻었다. X-ray photoelectron spectroscopy (XPS) 분석 결과로부터 표면 반응을 조사하여, 식각 기구를 고찰하였다.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.4
• /
• pp.56-62
• /
• 1999

In this study, (Ba, Sr)$TiO_3$ thin films were etched with $Cl_2$/Ar gas mixing ratio in an inductively coupled plasma (ICP) by varying the etching parameter such as rf power, dc bias voltage, and chamber pressure. The etch rate was 56 nm/min under $Cl_2$/($Cl_2$+Ar) gas mixing ratio of 0.2, rf power of 600 W, dc bias voltage of 250 V, and chamber pressure of 5 mTorr. At this time, the selectivity of BST to Pt, $SiO_2$ was respectively 0.52, 0.43. The surface reaction of the etched (Ba, Sr)$TiO_3$ thin films was investigated with X-ray photoelectron spectroscopy (XPS). Ba is removed by chemical reaction between Sr and Cl to remove Sr. Ti is removed by chemical reaction such as $TiCl_4$ with ease. The results of secondary ion mass spectrometer (SIMS) analysis compared with the results of XPS analysis and the results were the same.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.50 no.5
• /
• pp.211-215
• /
• 2001

SBT thin films were etched at different content of $Cl_2$ in $Cl_2$/Ar or $Cl_2/N_2$(80%). As $Cl_2$ gas increased in $Cl_2$/Ar or $Cl_2/N_2$ gas plasma. the etch rate decreased. The result indicates that physical puttering of charged particles is dominant to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron to chemical reaction in etching SBT thin films. To evaluate the etching mechanism of SBT thin films, x-ray photoelectron spectroscopy (XPS), secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM) were carried out. From the result of AFM, the rms values of etched samples in Ar only or $Cl_2$ only plasma were higher than that of as-deposited, $Cl_2$/Ar and $Cl_2/N_2$ plasma. This can be illustrated by a decrease of Bi content of nonvolatile etching products (Sr-Cl and Ta-Cl), which are revealed by XPS and SIMS.