• Journal of Sensor Science and Technology
• /
• v.9 no.3
• /
• pp.242-247
• /
• 2000

$Pb_{0.99}[(Zr_{0.6}Sn_{0.4})_{0.9}Ti_{0.1}]_{0.98}Nb_{0.02}O_3(PNZST)$ thin films were deposited by RF magnetron sputtering on $(La_{0.5}Sr_{0.5})CoO_3(LSCO)/Pt/Ti/SiO_2/Si$ substrate using a PNZST target with excess PbO of 10 mole%. The thin films deposited at substrate temperature of $500^{\circ}C$, and at RF power of 80W were crystallized to a perovskite phase after rapid thermal annealing(RTA). The thin films annealed at $650^{\circ}C$ for 10 seconds in air exhibited the good structures and electrical properties. The fabricated PNZST capacitor had a remanent polarization value of about $20\;{\mu}C/cm^2$ and coercive field of about 50 kV/cm. The reduction of the polarization after $2.2{\times}10^9$ switching cycles was less than 10%.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.54 no.3
• /
• pp.78-86
• /
• 2017

In this paper, we propose hidden object detection system using parametric array based on acoustic signal that is harmless to human body. A transmit signal of the proposed detection system uses a high directive chirp signal generated from parametric array phenomenon, which uses technique to improve a signal to noise (SNR) of a received signal and a distance resolution trough the dechirp processing. The transmit sensor array is constructed as $8{\times}2$ and has a horizontal beam width of $7^{\circ}$ and vertical beam width of $26^{\circ}$. To verify the detection and visualization of the proposed system, a 2-axis driving control system based on linear stage was constructed, and A-scan, B-scan, and C-scan experiments was addressed for hidden object. From experimental results, we detected and visualized the hidden bronze plate and pipe by cloth and the visualized shapes was confirmed. Especially, the obtained errors was $0.015m^2$ for bronze plate, and $0.046m^2$ for pipe.

• Proceedings of the Plant Resources Society of Korea Conference
• /
• 2018.10a
• /
• pp.77-77
• /
• 2018

천마(Gastrodia elata)는 연중생산을 위해 실내시설 재배 시 생육모델을 구죽하고, 생육단계에 따른 온도, 수분, $CO_2$ 등 환경 조건 설정이 필요하다. 본 연구는 천마의 생육단계 중 괴경형성기와 괴경비대기의 수분함량을 설정하여 최적의 환경조건을 찾기 위해 수행하였다. 먼저 괴경형성기 수분함량 공급은 괴경형성기에 -20kPa, -30kPa, -40kPa로 처리하여 120일간 배양한 뒤, 괴경비대기를 -40kPa로 고정하여 60일간 배양하였다. 반면, 괴경비대기 수분함량 공급은 괴경형성기를 -30kPa로 고정하여 120일간 배양한 뒤 괴경비대기에 -20kPa, -30kPa, -40kPa, -50kPa로 처리하여 60일간 배양하였다. Tensiometer(토양수분장력계)기를 설치하여 수분을 공급하였고, FDR센서 (UbiMas, CoCo sensor, Frequency domain reflectometry type)를 배양토의 깊이 5 cm와 15 cm에 2개를 설치하여 평균값으로 수분함량을 측정하였으며, 전체수량, 성마율, 종마율 등을 조사하였다. FDR센서로 수분함량을 측정한 결과, -20 kPa은 43.3%, -30 kPa은 34.7%, -40 kPa은 29.8%, -50 kPa은 25.3%로 측정되었다. 괴경형성기 수분함량 처리 후 수확기의 상자 당 전체수량은 -30 kPa일 때 985 g으로 가장 많았고, -40 kPa일 때 912 g, -20 kPa일 때 703 g으로 처리간의 유의적인 차이를 보였다. 성마율은 수분함량처리별 각각 25, 34, 30% 이었고, 종마율은 수분함량처리별 각각 53, 73, 65%로 나타났다. 따라서 -30 kPa 처리구가 다른 처리구에 비해 전체수량, 성마율, 종마율 등이 유의적으로 우수하였다. 괴경비대기 수분 함량 처리 후 수확기의 상자 당 전체수량은 -40 kPa일 때 992 g으로 가장 많았고, -50 kPa일 때 955 g, -30 kPa일 때 903 g, -20 kPa일 때 686 g 순으로 나타났다. -30 kPa에서 -50 kPa 사이에서는 전체 수량의 유의성 차이는 없었다. 성마율은 수분함량처리별 각각 20, 30, 35, 33%이었고, 종마율은 수분함량처리별 각각 45, 65, 75, 68%로 나타났다. 따라서 -40 kPa 처리구가 다른 처리구에 비해 전체수량, 성마율, 종마율 등이 유의적으로 우수하였다. 반면 -20 kPa 처리구는 과도한 수분으로 천마가 오히려 부패될 수 있는 환경조건이 조성됨에 따라 성마율, 종마율 등 전체적인 수량 감소에 영향을 미친 것으로 판단되었다.

• Applied Chemistry for Engineering
• /
• v.9 no.5
• /
• pp.704-709
• /
• 1998

Non-linear optical polymer based on poly (${\alpha}$-methylstyrene-co-maleic anhydride) (MSMA) substrate polymer was prepared by polymer reaction method and its thermal and electro-optic properties were examined. In the polymer reaction between MSMA substrate polymer and 2-[4-(4-nitrophenylazo)-N-ethylphenylamino]ethanol (DR1) chromophore, the degree of substitution of DR1 into MSMA was higher with the 4-dimethylaminopyridine (DMAP) as catalyst and 3-dicyclohexyl carbodiimide (DCC) as dehydrating agent (sample, MSMA-DC) than the one with just 4-dimethylaminopyridine as catalyst (sample, MSMA-D). The synthesized NLO polymer (MSMA-DC) exhibited electro-optic coefficient of 18 pm/V (632.8 nm) and glass transition temperature ($T_g$) of about $175^{\circ}C$.

• Korean Journal of Remote Sensing
• /
• v.37 no.3
• /
• pp.431-447
• /
• 2021

Recently, the use of high-resolution satellites is increasing in many areas. In order to supply useful satellite images stably, it is necessary to establish automatic precision geometric correction technic. Geometric correction is the process that corrected geometric errors of satellite imagery based on the GCP (Ground Control Point), which is correspondence point between accurate ground coordinates and image coordinates. Therefore, in the automatic geometric correction process, it is the key to acquire high-quality GCPs automatically. In this paper, we proposed iterative precision geometry correction method. we constructed an image pyramid and repeatedly performed GCP chip matching, outlier detection, and precision sensor modeling in each layer of the image pyramid. Through this method, we were able to acquire high-quality GCPs automatically. we then improved the performance of geometric correction of high-resolution satellite images. To analyze the performance of the proposed method, we used KOMPSAT-3 and 3A Level 1R 8 scenes. As a result of the experiment, the proposed method showed the geometric correction accuracy of 1.5 pixels on average and a maximum of 2 pixels.

• Asian Journal of Atmospheric Environment
• /
• v.6 no.2
• /
• pp.96-103
• /
• 2012

Ambient particulate matter (PM) and particle-bound polycyclic aromatic hydrocarbon (PAH) concentrations were measured continuously for 70 days at a Korean elementary school located near a highway. The $PM_{10}$, $PM_{2.5}$, and $PM_1$ values were measured with a light-scattering, multi-channel, aerosol spectrometer (Grimm, Model 1.107). The number concentrations of the particles were measured using a scanning mobility particle sizer and counter (SMPS+C) which counted particles from 11.1 to 1083.3 nm classified in 44 channels. Particle-bound PAHs were measured with a direct reading, photoelectric aerosol sensor. The daily $NO_2$, $SO_2$, and CO concentrations were obtained from a national air-monitoring station located near the school. The average concentrations of $PM_{10}$, $PM_{2.5}$, and $PM_1$ were 75.3, 59.3, and $52.1{\mu}g/m^3$, respectively. The average number concentration of the ultrafine particles (UFPs) was $46,307/cm^3$, and the averaged particle-bound PAHs concentration was $17.9ng/cm^3$ during the study period. The ambient UFP variation was strongly associated with traffic intensity, particularly peak concentrations during the traffic rush hours. Particles <100 nm corresponded to traffic-related pollutants, including PAHs. Additional longterm monitoring of ambient UFPs and high-resolution traffic measurements should be carried out in future studies. In addition, transient variations in the ambient particle concentration should be taken into consideration in epidemiology studies in order to examine the short-term health effects of urban UFPs.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.480-480
• /
• 2011

양극산화(anodization)는 금속을 전기화학적으로 산화시켜 금속산화물로 만드는 기술로서 최근 다양한 크기의 나노 구조를 제조하는 기술로 각광받고 있으며, 이러한 기술에 의하여 얻어지는 anodic aluminum oxide(AAO)는 magnetic data storage, optoelectronic device, sensor에 적용될 수 있는 nano device 뿐만 아니라 nanostructure를 제조하기 위한 template 및 mask로써 최근 광범위 하게 연구되고 있다. 또한, AAO는 Al2O3의 단단한 구조를 가진 무기재료이므로 solid mask로써 다른 porous materials 보다 뛰어난 특성을 갖고 있다. 또한 electron-beam lithography 및 block co-polymer 에 의한 patterning 과 비교하여 매우 경제적이며, 재현성이 우수할 뿐만 아니라 대면적에서 나노 구조의 크기 및 형상제어가 비교적 쉽기 때문에 널리 사용되고 있다. 그러나, AAO 형성 시 생기게 되는 반구형 모양의 barrier layer는 물질(substance)과 기판과의 direct physical and electrical contact을 방해하기 때문에 해결해야 할 가장 큰 문제점 중 하나로 알려져 있다. 따라서 본 연구에서는 실리콘 기판위의 형성된 AAO의 barrier layer를 Cl/BCl3 gas mixture에서 Neutral Beam Etching (NBE)과 Ion Beam Etching (IBE) 로 각각 식각한 후 그 결과와 비교하였다. NBE와 IBE 모두 Cl2/BCl3 gas mixture에서 BCl3 gas의 첨가량이 60% 일 경우 etch rate이 가장 높게 나타났고, optical emission spectroscopy (OES)로 Cl2/BCl3 플라즈마 내의 Cl radical density와 X-ray photoelectron spectroscopy (XPS)로 AAO 표면 위를 관찰한 결과 휘발성 BOxCly의 형성이 AAO 식각에 크게 관여함을 확인 할 수 있었다. 또한, NBE와 IBE 실험한 다양한 Cl2/BCl3 gas mixture ratio 에서 AAO가 식각이 되지만, 이온빔의 경우 나노사이즈의 AAO pore의 charging에 의해 pore 아래쪽의 위치한 barrier layer를 어떤 식각조건에서도 제거하지 못하였다. 하지만, NBE에서는 BCl3-rich Cl2/BCl3 gas mixture인 식각조건에서 AAO pore에 휘발성 BOxCly를 형성하면서 barrier layer를 제거할 수 있었다.

• Korean Journal of Materials Research
• /
• v.28 no.8
• /
• pp.466-473
• /
• 2018

Nickel oxide(NiO) thin films, nanorods, and carbon nanotube(CNT)/NiO core-shell nanorod structures are fabricated by sputtering Nickel at different deposition time on alumina substrates or single wall carbon nanotube templates followed by oxidation treatments at different temperatures, 400 and $700^{\circ}C$. Structural analyses are carried out by scanning electron microscopy and x-ray diffraction. NiO thinfilm, nanorod and CNT/NiO core-shell nanorod structurals of the gas sensor structures are tested for detection of $H_2S$ gas. The NiO structures exhibit the highest response at $200^{\circ}C$ and high selectivity to $H_2S$ among other gases of NO, $NH_3$, $H_2$, CO, etc. The nanorod structures have a higher sensing performance than the thin films and carbon nanotube/NiO core-shell structures. The gold catalyst deposited on NiO nanorods further improve the sensing performance, particularly the recovery kinetics.

• Proceedings of the KOSOMBE Conference
• /
• v.1998 no.11
• /
• pp.285-286
• /
• 1998

Virtual Brain-endoscopy is an effective method to detect lesion in brain. Brain is the most part of the human and is not easy part to operate so that reconstructing in 3D may be very helpful to doctors. In this paper, it is suggested that to increase the reliability, method of matching 3D object with the 2D CT slice. 3D Brain-endoscopy is reconstructed with 35 slices of 2D CT images. There is a plate in 3D brain-endoscopy so as to drag upward or downward to match the relevant 2D CT image. Relevant CT image guides the user to recognize the exact part he or she is investigating. VRML Script is used to make the change in images and PlaneSensor node is used to transmit the y coordinate value with the CT image. The result is test on the PC which has the following spec. 400MHz Clock-speed, 512MB ram, and FireGL 3000 3D accelerator is set up. The VRML file size is 3.83MB. There was no delay in controlling the 3D world and no collision in changing the CT images. This brain-endoscopy can be also put to practical use on medical education through internet.

• Korean Journal of Metals and Materials
• /
• v.47 no.6
• /
• pp.372-377
• /
• 2009

We report on hysteresis behavior in the electrical resistance-hydrogen concentration of Pd thin films. The variation of the electrical resistance has been investigated during the process of absorption and desorption of hydrogen gas ($H_{2}$) as a function of thickness of Pd thin films. The hysteresis behavior in the electrical resistance with $H_{2}$ concentration was found for Pd thin films and consists of $\alpha$ phase, ${\alpha}+{\beta}$ phase, and $\beta$ phase regions. The sensitivity of Pd thin films with $H_{2}$ concentration was found to follow Sieverts' law in the $\alpha$ phase region. However, the sensitivity was observed to increase abruptly with $H_{2}$ concentration in the ${\alpha}+{\beta}$ phase co-exist region. This is because Pd-H interaction is stronger in the $\beta$ phase than in the $\alpha$ phase and needs a higher concentration gradient as a driving force to desorb. The formation of the $\beta$ phase also was observed to cause the structural change because of the lattice expansion during absorption. The hysteresis height and the trace of structural change were affected by the thickness of the Pd film. As the film becomes thinner, the hysteresis height becomes lower and the amount of delamination on the surface becomes smaller. For films thinner than 20 nm in thickness, the delamination was not found but electrical resistance hysteresis was still observed.