• Journal of Biosystems Engineering
• /
• v.26 no.5
• /
• pp.461-468
• /
• 2001

Impact between fruits and other materials is a major cause of product damage in harvesting and handling systems. The oriental pears are more susceptible to bruising than other fruits such as European pears and apples, and are required more careful handling. The interest in the handling of the pears for the processing systems has raised the question of the allowable drop height to which pears can be dropped without causing objectionable damage. Drop tests on pears were conducted using an impact device developed by authors to estimate the allowable drop height without bruising. The impact device was constructed to hold in a selected orientation and to release a fruit by vacuum for dropping on to a force transducer. The drop height was adjustable for zero to 60 cm to achieve the desired distance between the bottom of the fruits and the top of the impact force transducer. The transducer was secured to 150 kg$\sub$f/ concrete block. The transducer signal was sampled every 0.17 ms with a strain gage measurement board in the micro computer where it was digitaly stored for later analysis. The selected sample fruit was Niitaka cultivar of pears which is one of the most promising fruit for export in Korea. The pears were harvested during the 1998 harvest season from an orchard in Daejeon. The sample fruit was selected from two groups which were stored for 3 months and 5 months respectively by the method of current commercial practice. The pears were allowed to stabilize at environmental condition(18$^{\circ}C$, 65% rh) of the experimental room. One hundred fifty six pears were tested from the heights of 5, 7.5. 10 and 12.5 cm while measurement were made of impact peak force, contact time, time to peak force, dwell time, pear diameter and mass. The bioyield strength and modulus of elasticity were measured using UTM immediately after each drop test. The allowable drop height was estimated on the base of bioyield strength of the pears in two ways. One was assumed the peak force during impact test increasing linearly with time, and the other was based on the actual drop test results. The computer program was developed for measuring the impact characteristics of the pears and analyzing the data obtained in the study. The peak force increased while contact times decreased with increasing drop height and contact times of the sample from the hard tissue group. The allowable drop height increased with increasing bioyield strength and contact times, and also varied with Poisson\`s ratio, mass and equilibrium radius of the pears. The allowable drop height calculated by a theoretical method was in the range from 1 to 4 cm, meanwhile, the estimated drop height considering the result of the impact test was in the range from 1 to 6 cm. Since the physical properties of fruits affected significantly the allowable drop height, the physical properties of the fruits should be considered when estimating the allowable drop height.

• Journal of The Korean Society of Inherited Metabolic disease
• /
• v.3 no.1
• /
• pp.86-93
• /
• 2003

Background : The SCL began screening of newborns and high risk group blood spots with tandem mass spectrometry (MS/MS) in April 2001. Our goal was to determine approximate prevalence of metabolic disorders, optimization of decision criteria for estimation of preventive effect with early diagnosis. This report describes the ongoing effort to identify more than 30 metabolic disorders by MS/MS in South Korea. Methods : Blood spot was collected from day 2 to 30 (mostly from day 2 to 10) after birth for newborn. Blood spot of high risk group was from the pediatric patients in NICU, developmental delay, mental retardation, strong family history of metabolic disorders. One punch (3.2 mm ID) of dried blood spots was extracted with $150{\mu}L$ of methanol containing isotopically labelled amino acids (AA) and acylcarnitines (AC) internal standards. Butanolic HCl was added and incubated at $65^{\circ}C$ for 15 min. The butylated extract was introduced into the inlet of MS/MS. Neutral loss of m/z 102 and parent ion mode of m/z 85 were set for the analyses of AA and AC, respectively. Diagnosis was confirmed by repeating acylcarnitine profile, urine organic acid and plasma amino acid analysis, direct enzyme assay, or molecular testing. Results : Approximately 31,000 neonates and children were screened and the estimated prevalence (newborn/high risk group), sensitivity, specificity and recall rate amounted to 1:2384/1:2066, 96.55%, 99.98%, and 0.73%, respectively. Confirmed 28 (0.09%) multiple metabolic disorders (newborn/high risk) were as follows; 13 amino acid disorders [classical PKU (3/4), BH4 deficient-hyperphenylalaninemia (0/1), Citrullinemia (1/0), Homocystinuria (0/2), Hypermethioninemia (0/1), Tyrosinemia (1/0)], 8 organic acidurias [Propionic aciduria (2/1), Methylmalonic aciduria (0/1), Isovaleric aciduria (1/1), 3-methylcrotonylglycineuria (1/0), Glutaric aciduria type1 (1/0)], 7 fatty acid oxidation disorders [LCHAD def. (2/2), Mitochondrial TFP def. (0/1), VLCAD def. (1/0), LC3KT def. (0/1). Conclnsion : The relatively normal development of 10 patients with metabolic disorders among newborns (except for the expired) demonstrates the usefulness of newborn screening by MS/MS for early diagnosis and medical intervention. However, close coordination between the MS/MS screening laboratory and the metabolic clinic/biochmical geneticists is needed to determine proper decision of screening parameters, confirmation diagnosis, follow-up scheme and additional tests.

• Journal of Animal Environmental Science
• /
• v.15 no.2
• /
• pp.91-98
• /
• 2009

Object of this study were to determine the influence of collection times of rumen fluid on in vitro dry matter digestibility (IVDMD) of forage crops. The donor cow was fed concentrate once a day and given free access to grass-legume mixture hay. Main plot was consisted of different collection time of rumen fluid; T1: 1 hour before concentrate feeding, T2: 1 hour after feeding, T3: 4 hour after feeding and T4: 8 hour after feeding. A total of 7 samples of 4 different forage crops (barely, Italian ryegrass, crimson clover, rye) were used for the estimation of IVDMD and tested in three replicates. For the $DAISY^{II}$ incubation, each sample was inserted into each filter bag then heat-sealed and incubated in a digestion vessel for 48 h at $39^{\circ}C$. The times of rumen fluid collection had no significant effect on the IVDMD values over all varieties except for 2 breeds of IRG (Kogreen and Kospeed). IVDMD values with T1 over all varieties were slightly higher than other treatments, however those with both T1 of Kogreen and Kospeed varieties were significantly higher than T2 (p<.05).

• Journal of Sericultural and Entomological Science
• /
• v.3
• /
• pp.61-67
• /
• 1963

This report is prepared to find how the filament of cocoon bave size deviation relates with the raw silk made by them which are intensively cultured in this country. Three recommended hybrid varieties and two varieties under working at Suwon Sericultural Experiment Station were selected as specimens. The cocoons were reeled as an individual filament of every fifty meters long skein with a wrap reel to weigh the denier and to investigate the relationship of the above statement so that it may be used for the quality estimation before processing it into raw silk. The conclusions obtained are as follows. (1) The variation of Pk${\times}$Sn was found as best cocoon for 21 denier raw silk use, but the number of cocoon to make the denier has to be eight which might cause more labor cost. (2) Baektoo-Kumkang and Myohiang-Chongchon were found as economical varieties for 21 denier use. (3) Seulak-Soyang is a proper variety for the use of 14 or 28 denier silk use. (4) Myohiang-Chongchon did not confirm a good property from the aspect of denier deviation. (5) It was found that there was a fairly strong corelationship between the mean cocoon bave size deviation as indicated by Ono's report. (6) Three graphs were prepared to estimate the cocoon quality before processing into various sizes of raw silk using the mean cocoon bave size and the raw silk size to be prepared. (7) Mean time, the graph which is able to estimate the expectable grade of the raw silk size deviation was designed for the practical use. (8) The expectable grade of the varieties used in this report were found as following data. Notice (A......cocoon number to make raw silk (B......total cocoon bave size deviation (C......expectable silk grade (9) The result of the work concerning the expectable denier deviation on 21 denier silk was the same with the statistical actual testing result as 1.25 D while the distribution showed farther necessity of improvement in technically.

• Korean Journal of Food Science and Technology
• /
• v.53 no.6
• /
• pp.739-748
• /
• 2021

This study focuses on the use of rice in the production of gluten-free rice udon (GFU) through an optimized mixing ratio, using the Box-Behnken response surface methodology (RSM). Different additional levels of rice flour (A, 40-60 g), acetylated distarch adipate (B, 10-20 g), and trehalose (C, 0-3 g) were used as variables, while water absorption level, volume, cooking loss, solid yield, lightness, texture properties, proximate compositions of GFU and turbidity of cooking water were set as responses in the RSM design model. The optimum mixing ratio for the preparation of gluten-free rice udon was obtained for 60.00 g of rice flour, 18.81 g of acetylated distarch adipate without the addition of trehalose. The response values of the optimized samples were water absorption (60.94%), volume (34.94%), turbidity of the cooking water (0.37), cooking loss (4.77%), solid yield (1.55 g), lightness value (70.04), hardness (2.53 N), springiness (0.18), gumminess (10.45 N), chewiness (1.83 N), and cohesiveness (2.89). This study has shown that rice flour can replace wheat flour to manufacture udon at an optimized mixing ratio successfully derived by statistical estimation method.

• International Area Studies Review
• /
• v.20 no.1
• /
• pp.23-51
• /
• 2016

This study analyzed the expected economic effects of the Korea-GCC FTA and sought strategies for industrial cooperation. To see the economic effects of Korea-GCC FTA, we analysed the effect of the oil tariff reduction of economy by Vector Autoregression(VAR) model. The estimation results shows that following the abolishment of the tariff on crude oil imports, GDP, GNI and consumption are expected to grow by 0.212%, 0.389% and 0.238%, respectively. Meanwhile, investment, export and import are estimated to drop by 0.462%, 0.413% and 0.342%, respectively. As for prices, producer prices are to rise by 6.356%p, whereas consumer prices fall by 2.996%p. In short, the Korea-GCC FTA and resultant abolishment of the tariff on crude oil imports followed by the decline in crude oil prices will result in declining prices whilst macroeconomic indices, such as GDP, GNI and consumption, will increase exerting positive effects on domestic economic growth. Also, it is necessary to proactively respond to GCC member states' industrial diversification policies for FTA-based industrial cooperation to diversify the sources of crude oil and natural gas imports for further resource risk management.

• Journal of the Korean Geosynthetics Society
• /
• v.17 no.4
• /
• pp.119-128
• /
• 2018

Limit state design has been implemented in Korea since 2015; however, there exists no specification of lateral load determination on retaining wall due to the Korean standard traffic load on retaining wall's backfill surface. The lateral load from traffic depends on lane number, standard truck's axle loads and locations, loading distance from the inner wall. The concept of equivalent height of soil accounting for traffic loadings is typically used for design of retaining walls to quantify the traffic loads transmitted to the inner wall faces. Due to the different characteristics of the standard design trucks between Korea and US (AASHTO), the direct use of the guidelines from AASHTO LRFD leads to incorrect estimation of traffic load effects on retaining walls. This paper presents the results of evaluation of equivalent height of soil to reflect the Korean standard truck, based on the findings from analytical solutions using Bounessq's theory and numerical assessment using 2D finite element method. Consequently, it was found that the equivalent heights of soil from the Korean standard truck load were lower for lower retaining wall height.

• Journal of the Korean GEO-environmental Society
• /
• v.20 no.2
• /
• pp.59-67
• /
• 2019

Using the results from laboratory soil test, field vane test and piezocone penetration test, the engineering characteristics of the soft ground at east side of Gwangyang Port, which is located at south coast of Jeollanam-do, were investigated and optimal piezocone penetration test depth was derived to calculate piezocone factor. In this paper, the results of 61 laboratory soil tests, 226 times of field vane tests and 26 piezocone penetration tests were used. The result of laboratory soil test suggested that some physical properties such as specific gravity, moisture content, liquid limit and plastic index and others are higher than other south coast regions, meanwhile uniaxial compression strength, undrained shear strength, defined as mechanical property, appeared to be relatively small, distributed widely. According to the plastic chart, the ground was classified as high compressibility clay and low compressibility clay, mostly represent to Type 3 clay by Robertson (1990)'s classification chart. Piezocone factor was calculated by empirical method, based on the undrained shear strength which was obtained by the field vane test. According to the analysis with 3 different depth range, to set the appropriate measured depth range of piezocone penetration for comparation, using average value of the range of 5 times the vane length showed the highest correlation.

• Korean Journal of Environmental Agriculture
• /
• v.38 no.3
• /
• pp.119-123
• /
• 2019

BACKGROUND: Estimation of soil nitrogen supply is essential to manage nitrogen fertilization in arable land. In Korea, nitrogen fertilization is recommended based on the soil organic matter content because it is difficult to assess nitrogen (N) mineralization of upland soils directly. In this study, the relationship between soil organic matter (SOM) content and N mineralization was investigated to explore the limitation of using SOM in predicting soil N mineralization. METHODS AND RESULTS: Soil samples from the 0 to 10 cm depth were collected from 18 individual pepper cultivated fields in Tae-an and Chung-yang provinces before fertilization. N mineralization in the soils was quantified using incubation for 70 days at $30^{\circ}C$. The mineralizable soil N (MSN) was positively correlated with SOM, and the relation equation between MSN and SOM was '$MSN(kg\;10a^{-1})=0.2933{\ast}SOM(g\;kg^{-1})+0.0897$ ($r^2=0.6224$, p<0.001)'. However, the differences of N mineralization among the soils with the similar concentrations of soil organic matter were about 3 to 4.6 times, suggesting that the other soil factors such as total N concentration or EC should affect N mineralization. CONCLUSION: We concluded that SOM alone could not reflect the capacity of soil to supply N that is used for recommendation of N fertilization rate. Therefore, other soil properties should be considered to improve N fertilization management in arable land for sustainable agriculture.

• Journal of the Korean Geotechnical Society
• /
• v.35 no.1
• /
• pp.5-15
• /
• 2019

In this study, the in situ deformation moduli, which were measured by borehole loading tests at basaltic rock masses located in the northeastern onshore and offshore and the northwestern onshore of Jeju Island, were examined in relation to RQD and RMR. The measured deformation moduli were also compared with the estimated deformation moduli from conventional empirical formulas using RQD and RMR. In addition, the measured deformation moduli were analyzed with respect to both the velocity ratio ($V_P/V_S$) and dynamic Poisson's ratio, which were obtained from the elastic wave velocities measured by velocity logging tests. As results, with only RQD, it was inappropriate to evaluate the quality of the Jeju island basaltic rock masses, which are characterized by vesicular structures, to select a measurement method of in situ deformation moduli, and to estimate the deformation moduli. On the other hand, it was desirable to evaluate the quality of the Jeju Island basaltic rock masses, and to estimate the deformation moduli by using RMR. The conventional empirical formulas using RMR overestimated the deformation moduli of the Jeju Island basaltic rock masses. There was qualitative consistency in the relation between velocity ratio and deformation moduli. To estimate appropriately the deformation moduli of the Jeju Island basaltic rock masses, empirical formulas were proposed as the function of RMR and velocity ratio, respectively.