• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 1999.02a
• /
• pp.51-53
• /
• 1999

The crystallization mechanism of an amorphous $Bi_{2}$$Sr_{2}$$Ca_{2 x}$$Cd_{x}$$Cu_{3}$$O_{y}$ phase were studied from the relations between crystallization and volume changes by dilatometry. Further, the effect of addition of CdO on the crystallization mechanism and superconductivity was discussed. The shrinkage of the amorphous $Bi_{2}$$Sr_{2}$$Ca_{2 x}$$Cd_{x}$$Cu_{3}$$O_{y}$ occurred with the crystallization of $Bi_{2}$$Sr_{2}$Cu$O_{6}$ phase decrease with increasing CdO content with a minimum at x=0.4. Better superconductivity was obtained in the specimens formation less amount of the$Bi_{2}$$Sr_{2}$Cu$O_{6}$ phase during the crystallization process.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.524-527
• /
• 2007

[ $Bi_2Sr_2Ca_{n-1}Cu_nO_x$ ](n=0, 1, 2) thin films have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about % K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $ CaCuO_2$ was observed in all of the obtained films.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.11 no.6
• /
• pp.1115-1121
• /
• 2007

[ $Bi_2Sr_2Ca{_{n-1}}Cu_nO_x$ ](n=0,1,2) thin fans have been fabricated by co-deposition at an ultra-low growth rate using ion beam sputtering(IBS) method. Bi 2212 phase appeared in the temperature range of 750 and $795^{\circ}C$ and single phase of Bi 2201 existed in the lower region than $785^{\circ}C$. Whereas, $PO_3$ dependance on structural formation was scarcely observed regardless of the pressure variation. And high quality of c-axis oriented Bi 2212 thin film with $T_c$(onset) of about 90 K and $T_c$(zero) of about 45 K is obtained. Only a small amount of CuO in some films was observed as impurity, and no impurity phase such as $CaCuO_2$ was observed in all of the obtained films.

• Journal of the Korean Vacuum Society
• /
• v.9 no.4
• /
• pp.373-378
• /
• 2000

There was a great difference in the formation kinetics of $TiO_2$ and $Bi_2O_3$ on silicon, but the growth of bismuth titanate (BIT) thin film was mainly limited by the formation of $TiO_2$. As a result, the BIT film was easy to be lack of bismuth. The pulse injection metalorganic chemical vapor deposition (MOCVD) process was introduced in order to overcome this problem by recovering the insufficient bismuth content in the film. By this pulse injection method, bismuth content was increased and also the uniform in-depth composition of the film was attained with a abrupt $Bi_4Ti_3O_{12}/Si$ interface. In addition, the crystallinity of $Bi_4Ti_3O_{12}$ thin film prepared by pulse injection process was greatly improved and the leakage current density was lowered by 1/2~1/3 of magnitude. Clockwise hysteresis of C-V was observed and the ferroelectric switching was confirmed for $Bi_4Ti_3O_{12}$ film deposited by pulse injection method.

• Journal of Korean Society of Water and Wastewater
• /
• v.32 no.4
• /
• pp.349-355
• /
• 2018

This study interrogated multi-layer heterojunction anodes were interrogated for potential applications to water treatment. The multi-layer anodes with outer layers of $SnO_2/Bi_2O_3$ and/or $TiO_2/Bi_2O_3$ onto $IrO_2/Ta_2O_5$ electrodes were prepared by thermal decomposition and characterized in terms of reactive chlorine species (RCS) generation in 50 mM NaCl solutions. The $IrO_2/Ta_2O_5$ layer on Ti substrate (Anode 1) primarily served as an electron shuttle. The current efficiency (CE) and energy efficiency (EE) for RCS generation were significantly enhanced by the further coating of $SnO_2/Bi_2O_3$ (Anode 2) and $TiO_2/Bi_2O_3$ (Anode 3) layers onto the Anode 1, despite moderate losses in electrical conductivity and active surface area. The CE of the Anode 3 was found to show the highest RCS generation rate, whereas the multi-junction architecture (Anode 4, sequential coating of $IrO_2/Ta_2O_5$, $SnO_2/Bi_2O_3$, and $TiO_2/Bi_2O_3$) showed marginal improvement. The microscopic observations indicated that the outer $TiO_2/Bi_2O_3$ could form a crack-free layer by an incorporation of anatase $TiO_2$ particles, potentially increasing the service life of the anode. The results of this study are expected to broaden the usage of dimensionally stable anodes in water treatment with an enhanced RCS generation and lifetime.

• Journal of the Korean Ceramic Society
• /
• v.35 no.11
• /
• pp.1130-1140
• /
• 1998

Thin films of $Bi_4Ti_3O_{12}\;nBaTiO_3(n=1&2)$ were prepared using sols erived Ba-Bi-Ti complex alkoxides. The sols were spin-cast onto $Pt/Ti/SiO_2/Si$ substrates and followed by pyrolysis for 1 hr at $620^{\circ}C,\;700^{\circ}C\;and\;750^{\circ}C$ In the thin films a pyrochlore phase seemed to be formed at a lower temperature and then tran-formed to the layered perovskite phase as the heating temperature increased. In the thin films pyrolyzed at formed to the layered perovskte phase as the heating temperature increased. In the films pyrolyzed at $750^{\circ}C$ the amount of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ reached to 94% while $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ was 77% in composition. This result shows that the formation of the layered pervoskite phase becomes difficult as the amount of complexing $BaTiO_3$ increases. The microstructures and the electrical properties of the thin films were gen-erally improved with the incease of the heating temperature. However the presence of the pyrochlore phase could not be removed effectively. Our study showed that the electrical properties of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ were pronouncedly improved with complexing with BaTiO3 when compared to those of $Bi_4Ti_3O_{12}$ while the presence of the pyrochlore phase was detrimental to the those of $Bi_4Ti_3O_{12}{\cdot}2BaTiO_3$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1988.05a
• /
• pp.3-6
• /
• 1988

Electrical and magnetic properties of $Y_1Ba_2Cu_3O_7-y$ sintered with $Bi_2O_3$ have been investigated by levitation experiment and the measurement of electrical resistivity. The effects of $Bi_2O_3$ addition on the microstructure of the sintered specimens were also investigated. The electrical resistivity in the normal state is smaller in $Y_{0.85}Bi_{0.15}Ba_2Cu_3O_{7-y}$, where the Bi is substituted into Y site, than in the basic compound $Y_1Ba_2Cu_3O_{7-y}$ due to improved microstructure. On the other hand, the microstructure is poor and electrical resistivity is larger in the $Y_1Ba_2Cu_3O_{7-y}$ sintered with excess $Bi_2O_3$. It appears that the impurity in grain boundary affect the electrical properties significantly but has little effect on the magnetic property.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.69-72
• /
• 1999

A Well oriented Bi$_2$re$_2$CaCu$_2$O$\sub$8/(Bi2212) superconductor thick films were formed successfully on a copper substrate by liquid reaction between a Cu-free precursor and Cu tape using method in which Cu-free BSCO powder mixture was printed on copper plate and heat-treated. And we examined the mechanism for the rapid formation of Bi2212 superconducting films from observing the surface microstructure with heat-treatment time. At heat-treatment temperature, the printing layer partially melt by reacting with CuO of the oxidizing copper plate, and the nonsuperconducting phases present in the melt are typically Bi-free phases and Cu-free phases. Following the partial melting, the Bi$_2$Sr$_2$CaCu$_2$O$\sub$8/ superconducting phase is formed at Bi-free phase/liquid interface by nucleation and grows. It was confirmed that the phase colony from the phase diagram of Bi$_2$O$_3$-(SrO+CaO)/2-CuO system is similar to the observed result.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.320-323
• /
• 1997

The microwave dielectric properties of X Ba0-$0.15(Nd_{0.87}Bi_{0.13})_2O_3$-(0.85-X) $TiO_2$ ($X=0.13{\sim}0.17$) and 0.16Ba0-$0.15(Bi_xNd_{1-x})_2O_3-0.69TiO_2$ ($X=0.10{\sim}0.16$) ceramics were investigated. Dielectric constant, quality factor and temperature coefficient of resonant frequency of 0.16Ba0-$0.15(Nd_{0.87}Bi_{0.13})_2O_3-0.69TiO_2$ ceramics sintered at $1320^{\circ}C$ for 2 hours were 89.2, 1920(at 4GHz) and 5.2ppm/$^{\circ}C$, respectively.

• Journal of the Korean Ceramic Society
• /
• v.26 no.5
• /
• pp.655-660
• /
• 1989

The physical properties and sinterabilities of ZrO2-Y2O3-Bi2O3 ternary system powder prepared by coprecipitation were investigated. The crystallization temperatures of ternary system were increased and the specific surface areas were decreased with increasing Bi2O3 amount as sintering agents both PSZ and FSZ. Especially, the partially stabilized zirconia showed monoclinic phase. The sinterability was increased with the amount of Bi2O3 added which caused liquid phase sintering.