• 한국세라믹학회지
• /
• 제35권11호
• /
• pp.1130-1140
• /
• 1998

Thin films of $Bi_4Ti_3O_{12}\;nBaTiO_3(n=1&2)$ were prepared using sols erived Ba-Bi-Ti complex alkoxides. The sols were spin-cast onto $Pt/Ti/SiO_2/Si$ substrates and followed by pyrolysis for 1 hr at $620^{\circ}C,\;700^{\circ}C\;and\;750^{\circ}C$ In the thin films a pyrochlore phase seemed to be formed at a lower temperature and then tran-formed to the layered perovskite phase as the heating temperature increased. In the thin films pyrolyzed at formed to the layered perovskte phase as the heating temperature increased. In the films pyrolyzed at $750^{\circ}C$ the amount of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ reached to 94% while $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ was 77% in composition. This result shows that the formation of the layered pervoskite phase becomes difficult as the amount of complexing $BaTiO_3$ increases. The microstructures and the electrical properties of the thin films were gen-erally improved with the incease of the heating temperature. However the presence of the pyrochlore phase could not be removed effectively. Our study showed that the electrical properties of $Bi_4Ti_3O_{12}{\cdot}BaTiO_3$ were pronouncedly improved with complexing with BaTiO3 when compared to those of $Bi_4Ti_3O_{12}$ while the presence of the pyrochlore phase was detrimental to the those of $Bi_4Ti_3O_{12}{\cdot}2BaTiO_3$.

• 한국세라믹학회지
• /
• 제32권7호
• /
• pp.761-768
• /
• 1995

Double layered BaTiO3 thin films with high dielectric constant as well as good insulating property were prepared for the application to low voltage driving thin film electroluminescent (TFEL) device. BaTiO3 thin films were formed by rf-magnetron sputtering technique. Amorphous and polycrystalline BaTiO3 thin films were deposited at the substrate temperatures of room temperature and 55$0^{\circ}C$, respectively. Two kinds of films prepared under these conditions showed high resistivity and high dielectric constant. The figure of merit (=$\varepsilon$r$\times$Eb.d) of polycrystalline BaTiO3 thin film was very high (8.43$\mu$C/$\textrm{cm}^2$). The polycrystalline BaTiO3 showed a substantial amount of leakage current (I), under the high electric field above 0.5 MV/cm. The double layered BaTiO3 thin film, i.e., amorphous BaTiO3 layer coated polycrystalline BaTiO3 thin film, was prepared by the new stacking method and showed very good dielectric and insulating properties. It showed a high dielectric constant fo 95 and leakage current density of 25 nA/$\textrm{cm}^2$ (0.3MV/cm) with the figure of merit of 20$\mu$C/$\textrm{cm}^2$. The leakage current density in the double layered BaTiO3 was much smaller than that in polycrystalline BaTiO3 under the high electric field. The saturated brightness of the devices using double layered BaTiO3 was about 220cd/$m^2$. Threshold voltage of TFEL devices fabricated on double layered BaTiO3 decreased by 50V compared to the EL devices fabricated on amorphous BaTiO3.

• 한국세라믹학회지
• /
• 제34권4호
• /
• pp.373-379
• /
• 1997

A study on the deposition and characterization of BaTiO3 thin films on MgO-buffered Si(100) substrates by sputtering was conducted. The MgO buffer layers were investigated as a function of deposition temperature. At lower substrate temperature, the MgO layers were not fully crystalline, but a crystallized MgO layer with (001) preferred orientation was obtained at the substrate temperature of $700^{\circ}C$. Partially (00ι) or (h00) textured BaTiO3 films were obtained on Si(100) with the MgO buffer layer grown at 700ι. While, randomly oriented BaTiO3 films with large-scale cracks on the surface were made without the MgO layer. The crystallographic orientation, morphology and electrical properties between the BaTiO3 films on Si with and without the MgO layer were compared using the BaTiO3 film on MgO(100) single crystal substrate as a reference system. Also the favorable role of the MgO layer as a buffer for growing of oriented BaTiO3 films on Si substrates was confirmed.

• 한국세라믹학회지
• /
• 제30권6호
• /
• pp.441-448
• /
• 1993

The Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ by rf magnetron sputtering method have individual preferential orientations as a function of composition (X=0, 0.25, 0.5, 0.75, 1) due to the stress relief interactions among the intrinsic compressive stress, thermal tensile stress adn extrinsic compressive stress (compressive stress in case of BaTiO3(Tc=12$0^{\circ}C$) and Ba0.75Sr0.25TiO3(Tc=57$^{\circ}C$)). This behavior also appears on the (BaSr)TiO3 thin films (X=0.5) deposited on ITO-coated glass substrate at deposition temperature between 35$0^{\circ}C$ and 55$0^{\circ}C$. The composition of Ba1-xSrxTiO3 thin films deposited on ITO-coated glass substrate at 55$0^{\circ}C$ is close to stoichiometry (1.009~1.089 in A/B ratio), but the compositional deviation from a stoichiometry is larger as SrTiO3 is added. The morphology of Ba1-xSrxTiO3 thin films is very similar for over all substrate temperatures, and the roughness due to the differences of cluster size is the smallest at X=0.25.

• 한국세라믹학회지
• /
• 제32권4호
• /
• pp.516-524
• /
• 1995

In this study, to prepare the dielectric (Ba, Sr)TiO3 thin films by the sol-gel process, Titaminum (IV) sio-propoxide (Ti[OCH(CH3)2]4), Ba and Sr acetate were used for sol and thin films were prepared by dip-coating process. Stability of sol decreased with the increase of Sr, and thickness of thin films were obtained 0.13~0.17${\mu}{\textrm}{m}$ by 1 coating cycle. Transmittance of amorphous thin films heated at 500 and 55$0^{\circ}C$ was very good, and crystallization tendency of thin films according to heat-treatment temperature and crystallization characteristics of thin films heated at 11$0^{\circ}C$ for 3 hrs were analysed. As a result, good perovskite structure was obtained higher than 100$0^{\circ}C$, and tetragonality of thin film was decreased but pyrochlore was formed with increasing Sr. In case of addition to substitute 0.4mol% Sr for Ba, dielectric constant was 288 and loss factor (tan $\delta$) was 0.04.

• 한국세라믹학회지
• /
• 제34권2호
• /
• pp.181-187
• /
• 1997

다결정 BaTiO3 박막의 높은 유전상수와 비정질 BaTiO3 박막의 우수한 절연특성을 함께 지닌 적층구조 BaTiO3 박막을 제조하여 적층방법에 따른 전기적 특성을 비교, 평가하였다. BaTiO3 박막은 ITO 투명전전막이 입혀진 유리기판위에 rf=magnetron sputtering방법으로 형성하였으며 적층구조 BaTiO3박막의 제조에는 다결정 BaTiO3 박막의 상부에 기판의 자연 냉각과정중에 비정질층이 형성되는 새로운 적층방법을 사용하였다. 이와같이 제조된 적층박막은 다결정 BaTiO3 박막의 상부에 상온에서 비정질층을 형성시키는 일반적인 적층방법으로 제조한 적층박막에 비하여 높은 단위면적당 정전용량과 유전상수, 우수한 절연특성을 나타내었다. 일반적인 적층방법에 의하여 이중층 구조가 형성되는 반면, 새로운 적층방법으로 제조된 적층박막은 AES depth profile과 전기적 특성 분석을 통하여 비정질/microcrystalline/다결정 구조의 다층구조를 지닌 것으로 확인되었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 제5회 학술대회 논문집 일렉트렛트 및 응용기술연구회
• /
• pp.100-104
• /
• 2003

$BaTiO_3$ ceramic thin films were manufactured by rf/dc magnetron sputter technique. We have investigated crystal structure, surface morphology and PTCR(positive-temperature coefficient of resistance) characteristics of the specimen depending on second heat-treatment temperatures. Second heat treatments of the specimen were performed in the temperature range of 400 to $1350^{\circ}C$. X-ray diffraction patterns of $BaTiO_3$ thin films show that the specimen heat treated below $600^{\circ}C$ is an amorphous phase and the one heat treated above $1100^{\circ}C$ forms a poly-crystallization. In the specimen heat-treated at $1300^{\circ}C$, a lattice constant ratio (c/a) was 1.188. Scanning electron microscope(SEM) image of $BaTiO_3$ thin films of the specimen heat treated in between 900 and $1100^{\circ}C$ shows a grain growth. At $1100^{\circ}C$, the specimen stops grain-growing and becomes a poly-crystallization.

• 한국세라믹학회지
• /
• 제40권4호
• /
• pp.380-384
• /
• 2003

The effects of the mole concentrations of precursor solution on the microstructure and dielectric properties of sol-gel deposited $Ba_{0.85}$S $r_{0.15}$Ti $O_3$(BST) thin films have been investigated. The films were of single perovskite phase with strong (100) preferred orientation when grown on LaNi0$_3$ buffered Pt/Ti/ $SiO_2$Si substrates using a diluted precursor solution. Variation of the precursor solution concentration resulted in a different microstructure and, in turn, affected the tunability of the sol-gel deposited films. It was observed that leakage currents increased asymmetrically for the negative and positive bias voltage with decreasing thickness. Overall results suggest that those BST films have acceptable properties f3r applications as room-temperature tunable elements.

• 한국세라믹학회지
• /
• 제40권2호
• /
• pp.198-205
• /
• 2003

R.F. Magnetron Sputtering법을 이용하여 Pt/Ti/ $SiO_2$/Si기판 위에 seed-layers와 $Ba_{0.66}$S $r_{0.34}$Ti $O_3$박막을 제조하였다. 다양한 기판온도에 따른 BST 박막의 전기적인 특성(정전용량과 누설전류)과 seed-layer층이 BST 박막에 미치는 영향을 조사하였다. BST 박막은 seed-layer층을 삽입함으로써 박막의 결정성이 향상되었고, 박막의 기판온도(결정화온도)도 상당히 낮출 수 있었다. 순수한 BST에 비하여 seed-layer를 삽입한 BST는 높은 유전상수와 낮은 유전손실 및 낮은 누설전류를 가지는 우수한 전기적 특성을 나타내었다. BST 박막의 전기적 특성은 기판온도에 따라 영향을 받고, seed-layer에 의해 향상됨을 알 수 있었다.

• 한국세라믹학회지
• /
• 제43권6호
• /
• pp.362-368
• /
• 2006

Epitaxial $Ba_{0.5}Sr_{0.5}TiO_3$ (BSTO) thin films have been grown on TiN buffered Si (001) substrates by Pulsed Laser Deposition (PLD) method and the effects of substrate temperature and oxygen partial pressure during the deposition on their dielectric properties and crystallinity were investigated. The crystal orientation, epitaxy nature, and microstructure of oxide thin films were investigated using X-Ray Diffraction (XRD) and Transmission Electron Microscopy (TEM). Thin films were prepared with laser fluence of $4.2\;J/cm^2\;and\;3\;J/cm^2$, repetition rate of 8 Hz and 10 Hz, substrate temperatures of $700^{\circ}C$ and ranging from $350^{\circ}C\;to\;700^{\circ}C$ for TiN and oxide respectively. BSTO thin-films were grown on TiN-buffered Si substrates at various oxygen partial pressure ranging from $1{\times}10^{-4}$ torr to $1{\times}10^{-5}$ torr. The TiN buffer layer and BSTO thin films were grown with cube-on-cube epitaxial orientation relationship of $[110](001)_{BSTO}{\parallel}[110](001)_{TiN}{\parallel}[110](001)_{Si}$. The crystallinity of BSTO thin films was improved with increasing substrate temperature. C-axis lattice parameters of BSTO thin films, calculated from XRD ${\theta}-2{\theta}$ scans, decreased from 0.408 m to 0.404 nm and the dielectric constants of BSTO epitaxial thin films increased from 440 to 938 with increasing processing oxygen partial pressure.