• Progress in Superconductivity
• /
• v.6 no.1
• /
• pp.19-23
• /
• 2004

YBCO do superconducting quantum interference device (SQUID) magnetometers based on bicrystal Josephson junctions on 10 mm ${\times}$ 10 mm $SrTiO_3$ substrates have been fabricated. The pickup coil of the device was designed to have 16 parallel loops with 50-fm-wide lines. We could obtain optimised direct coupled YBCO SQUID magnetometer design with field sensitivity $B_{N}$ $\Phi$/ of $4.5 nT/\Phi_{0}$ and magnetic field noise $B_{N}$ of about $22 fT/Hz^{1}$2/ with an I/f corner frequency of 2 Hz measured inside a magnetically shielded room. Preliminary results of magnetocardiograph measurement using the HTS SQUID magnetometers show signal to noise ratio of about 110, which is comparable to the quality of a commercial MCG system based on Nb-SQUIDs.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.17-19
• /
• 2002

Melt textured YBCO superconductors were fabricated by the top seeding method using Sml.8($Sm_{1.8}$ $Ba_{2.4}$ $Cu_{3.4}$$O_{7-Y}$) seed. We investigated the twin structures using the optical microscope, SEM and TEM. The twin structures formed during the tetragonal to orthorhombic transition which occurred at $450^{\circ}C$ in sample oxygen annealing. The twin structures were clearly observed by SEM due to the chemical etching effects. The lengths of twin structures were increased as the oxygenation heat treatment time increased from 1hr to 10hr. We investigated twin structure by TEM. The twin spaces were considered to be related to the oxygen contents. The results suggested an oxygen diffusion model for the formation of the twin lengths.

• Proceedings of the KIEE Conference
• /
• 1998.07d
• /
• pp.1255-1257
• /
• 1998

In this study,$ 5{\times}5$ dot-matrix display was implemented with powder electroluminescent device (PELD). Generally PELD which have a luminance from powder phosphor with electric field, inserted phosphor and dielectric layer between electrodes is basic structure. To make high brightness PELD compared to conventional device, new type of PELD was proposed as follows. New PELD had only one layer, which was mixed phosphor (ZnS:Cu) and dielectric (BaTiO3) material appropriately between electrodes. To compare and estimate the conventional and new type of PELD, the EL spectrum, transferred charge density, brightness and decay time was measured. As above result, we fabricated a hish brightness $ 5{\times}5$ dot-matrix display with new type of PELD. Its brightness was 6400 $cd/m^2$ at 200 V, 400Hz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03b
• /
• pp.12-12
• /
• 2010

The hall probe measurement system was used to measure the critical current distribution of superconducting coated conductor. The system consists of reel to reel moving apparatus, 7 array hall probe, a rotary encoder and permanent magnet. The magnetic field profile across the width of superconducting coated conductor using Bean's critical state model was calculated. The effect of various parameters of the formulas on the magnetic field distribution and the effect of shape and size of artificial defects, which were formed on the surface of SmBa2Cu3O7-d(SmBCO) coated conductor using laser marking system, on the hall probe magnetic field signal of the hall probe measurement system was investigated.

• Progress in Superconductivity
• /
• v.3 no.1
• /
• pp.83-86
• /
• 2001

We have fabricated a single flux quantum 4-stage shift register with interface-controlled $Y_1$$Ba_2$$Cu_3$$O_{7-x}$(YBCO) Josephson junction. The YBCO Josephson junctions showed RSJ-like current-voltage(I-V) curves at temperatures 45~80K. We tested load and shift operation of shift register with binary data sequences “1000”, “1010”, “1011”, and “1111” at 58K. For all the binary data sequences, the shift register operated successfully. By operating the circuit with proper current pulses, we observed no errors during at least 12 hours operation for all the data sequences.s.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.189-192
• /
• 2000

We fabricated rapid single-flux-quantum RS flip-flop circuits with and without Y$_1$Ba$_2$Cu$_3$O$_{7-{\delta}}$(YBCO) ground plane. The circuit consists of SNS-type ramp-edge Josephson junctions that have cobalt-doped YBCO and Sr$_2$AITaO$_6$(SAT) for barrier layer and insulator layer, respectively. The fabricated Josephson junction showed a typical RSJ-like current-voltage(I-V) characteristics above 50K. We sucessfuly demonstrated RS flip-flop at temperatures around 50K. The RS flip-flop fabricated on ground plane showed more definite set and reset state in voltage-flux(V-${\phi}$) modulation curve for read SQUID, which may be attributed to a shielding effect of the YBCO ground plane.

• Progress in Superconductivity
• /
• v.5 no.2
• /
• pp.118-123
• /
• 2004

We investigated quench distribution in AU/YBCO thin film meander lines with a heater. Quench distribution during faults is important for superconducting fault current limter applications, because uniform quench allows application of higher voltages across the meander lines. AU/YBCO thin films grown on sapphire substrates were patterned into meander lines by photolithography. Gold films grown on the rear sides of the substrates were also patterned into meander lines, and used as heaters. Meander lines on the front and the rear sides were connected in parallel. The meander lines were subjected to simulated AC fault currents for quench measurements during faults. They were immersed in liquid nitrogen during the experiment for effective cooling. Resistance of the AU/YBCO meander lines initially increased more rapidly with the rear heater than without, and consequently the fault current was limited more. The resistance subsequently became similar, The resistance distribution was more uniform with the heater, especially during the initial quench. Quench was completed more uniformly and significantly earlier. This resulted in uniform distribution of dissipated power. These results could be explained with the concept of quench propagation, which was accelerated by heat transfer across the substrate from the rear heater.

• Progress in Superconductivity and Cryogenics
• /
• v.21 no.1
• /
• pp.15-17
• /
• 2019

We present terahertz optical properties of $GdBa_2Cu_3O_{7-x}$ (GdBCO) superconducting thin films. GdBCO films with a thickness of about 105 nm were grown on a $LaAlO_3$ (LAO) single crystal substrate using a conventional pulsed laser deposition (PLD) technique. Using an Ar ion milling system, the thickness of the GdBCO film was reduced to 58 nm, and its surface was also smoothened. Terahertz (THz) transmission spectra through two different GdBCO films are measured over the range between 0.2 and 1.5 THz using THz time domain spectroscopy. Interestingly, the THz transmission of the thinner GdBCO film has been increased to six times larger than that of the thicker one, while the thinner film is still maintaining its superconducting property at below 90 K.

• Analytical Science and Technology
• /
• v.14 no.4
• /
• pp.311-316
• /
• 2001

We have investigated the trace amount in an oriental medicine in oder to determine the geographical origin by using inductively coupled plasma-atomic emission spectrometry(ICP-AES) and chemometric anlysis with principal component analysis(PCA) and pattern recognition. Astragali Radix from several agricultural places in Korea was selected as an example of the oriental medicine and analyzed by ICP-AES. The dried Astragali Radix sample was treated with $HNO_3$ and $H_2O_2$, then digested using microwave oven. Elements such as Mg, Al, K, Ca, Ti, Mn, Fe, Cu, Zn, and Ba with different concentrations were found an used for the identification of the origin of agriculture places. Especially, the concentration of Al, Fe, Zn and Ti were employed to investigate the relationship between. Astragali Radix and the agricultural places by PCA and pattern recognition. We have made a program that is based on chemometrics in analytical spectroscopy. The results of the chemometrics analysis indicated that a distinction among Yechon and Chechon, Chungson, Kurye and Chinese Astragali Radix could be made. We believe that principal component analysis(PCA) and pattern recognition is a valuable tool to identify the origin of Astragali Radix in terms of the agricultural place.

• Progress in Superconductivity and Cryogenics
• /
• v.19 no.3
• /
• pp.13-17
• /
• 2017

We investigated the effect of self-assembled BSO nano-defects as pinning centers in BSO-added GdBCO films when the thicknesses of films were varied. 3.5 vol. % BSO-added GdBCO films with varying thicknesses from 200 nm to 1000 nm were deposited on $SrTiO_3$ (STO) substrate by using pulsed laser deposition (PLD) process. For the films with thicknesses of 400 nm and 600 nm, 'anomaly shoulders' in $J_c-H$ characteristic curves were observed near the matching field. The anomaly shoulders appeared in the field dependence of $J_c$ may be attributed to the existence of double pinning mechanisms in thin films. The fit to the pinning force density as a function of reduced field h ($H/H_{irr}$) using the Dew-Hughes' scaling law shows that both the 400 nm- and the 600 nm-thick films have double pinning mechanisms while the other films have a single pinning mechanism. These results indicate that the self-assembled property of BSO result in different role as pinning centers with different thickness.