• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.189-189
• /
• 2008

Due to the environmental issue vast research is going on to replace the widely used lead contented piezoelectric materials. Bismuth sodium titanate (abbreviated as BNT) based bismuth sodium titanate-barium titanate (abbreviated as BNBT) ceramic was prepared by using modified method rather than conventional mixed oxide method. This modification was made to improve the properties of BNT based ceramic. In this procedure $BaTiO_3$ (abbreviated as BT) was prepared using conventional mixed oxide method. Analytical grade raw materials of $BaCO_3$ and $TiO_2$ were weighted and ball milled using ethanol medium. The mixed slurry was dried and sieved under 80 mesh. Then the powder was calcined at $1100^{\circ}C$ for 2 hours. This calcined BT powder was used in the preparation of BNBT. Stoichiometric amount of $Bi_2O_3$, $Na_2CO_3$, $TiO_2$ and BT were weighted and mixed by using ball mill. The used calcination temperature was $850^{\circ}C$ for 2 hours. Calcined powder was taken for another milling step. BNBT disks were pressed to 15 mm of diameter and then cold isostatical press (CIP) was used. Pressed samples were sintered at $1150^{\circ}C$ for 2 hours. The SEM microstructure analysis revealed that the grain shape of the sintered ceramic was polyhedral and grain boundary was well matched where as the sample prepared by conventional method showed irregular arrangement and grain boundary not well matched. And sintered density was better (5.78 g/cc) for the modified method. It was strongly observed that the properties of BNBT ceramic near MPB composition was found to be improved by the modified method compare to the conventional mixed oxide method. The piezoelectric constant dB of 177.33 pC/N, electromechanical coupling factor $k_p$ of 33.4%, dielectric constant $K_{33}^T$ of 688.237 and mechanical quality factor $Q_m$ of 109.37 was found.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.06a
• /
• pp.60-60
• /
• 2008

We manufactured Liquid Crystal Polymer (LCP) and (1-x)$BaTiO_3-xSrTiO_3$(BST) ceramic composites and investigated dielectric properties to use as embedded capacitor in printed circuit boards and replace LTCC substrates. The dielectric properties of these composites are varied with volume fraction of BST and ratios of BT/ST. Dielectric constants are in the range of 3~28. In addition, we could get low TCC and High Q value that could not achieve in other ceramic-polymer composites. Especially, in composite with x=0.4 and 50vol% BST, the dieletric constant and Q-value are 27 and 300, respectively. And more TCC is -116~145ppm/$^{\circ}C$ in the temperature range of -55~$125^{\circ}C$. We think that this composites can be used high-Q substrate material like LTCC and embedded temperature compensation capacitor in printed circuit boards.

• Nano
• /
• v.13 no.12
• /
• pp.1850149.1-1850149.10
• /
• 2018

Ferroelectric particles have been applied in the photocatalytic field because the spontaneous polarization results in the internal electric field, which can accelerate the separation and migration of photogenerated carriers. In this study, the $BaTiO_3$ (BT) fibers are synthesized by electrospinning. The BT fibers calcined above $800^{\circ}C$ exhibit a strong ferroelectric property, which is verified by a typical butterfly-shaped displacement-voltage loop. It is found that the BT fibers with the single-domain structure exhibit better photocatalytic performance than that with the multi-domain configuration. When the single-domain transforms into multi-domain, the integrated internal electric field correspondingly breaks up, inducing that the internal electric field might cancel each other out and diminish the separation of photogenerated carriers. Also, the Au nanoparticles can improve the photocatalytic activity further on account of the surface plasmon resonance. Therefore, it is suggested that Au nanoparticles decorated on ferroelectric BT nanomaterials are promising photocatalysts.

• Journal of the Korean Ceramic Society
• /
• v.41 no.12 s.271
• /
• pp.884-888
• /
• 2004

Effects of NiO were studied in aspects of dielectric properties and microstructure of $0.96(0.91Pb(Mg_{1/3}Nb_{2/3})O_3-0.09PbTiO_3)­0.04BaTiO_3$ (PMN-PT-BT, PBT). The PBT was prepared by a conventional mixed oxide method using $(MgCO_3)_4{\cdot}Mg(OH)_2$ instead of MgO through Lewis acid-base interaction. NiO was added in the range of 0.5 to $3.0\;wt\%$ as thermally decomposable $2NiCO_3{\cdot}3Ni(OH)_2$ and it seemed to enhance densification to a large extent below $1000^{\circ}C$. But all the systems gave rise to ceramics with almost same relative sintered density of 96% by sintering at $1000^{\circ}C$ for 2 h. But it turned out that the addition of NiO was detrimental to dielectric constant but beneficial to the loss of dielectric constant.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.3
• /
• pp.328-331
• /
• 2024

This research explores the development of [100]-textured barium titanate (BaTiO₃, BT) ceramics using sodium bismuth titanate (Na_0.5Bi_4.5Ti₄O₁₅, NBiT) templates, aimed at leveraging the inherent high dielectric property of BT. However, the attempted texturing was unsuccessful, primarily due to bismuth diffusion from the NBiT templates into the BT matrix below the sintering temperature, at 1,000℃. Systematical exploration about the cause of the failure is involved and alternative approaches are proposed in detail to overcome the challenge. These findings contribute to the understanding of techniques and conditions for textured ceramic fabrication and highlight the need for further research in this area.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.3
• /
• pp.253-260
• /
• 1992

In this study, the dielectric, structural and electrical properties of Pb(ZnS11/3TNbS12/3T)OS13T-BaTiOS13T-PbTiOS13T system ceramics were investigated with respect to the variation of YS12TOS13T addition amount. As the YS12TOS13T addition amount is increased, the resistivity at 100$^{\circ}C$ and the resonant/antiresonant frequencies and the frequency constant are slowly increased, and the grain growth is restrained until 0.4 wt% YS12TOS13T addition amount but continuously increased with the addition amount more than 0.4 wt% YS12TOS13T. As the YS12TOS13T addition amount is increased, the density, the diffuseness of dielectric constant and the induced polarization are increased until 0.4 wt% YS12TOS13T addition.

• Journal of the Korean Ceramic Society
• /
• v.55 no.6
• /
• pp.581-589
• /
• 2018

This work concentrated on the effect of different laser beams on the microstructure and dielectric properties of $BaTiO_3$ nanoparticles at different calcinations times during the gelling preparation step. The nanoparticles were prepared by the sol-gel method. A green (1000 mW, 532 nm) and red laser beam (500 mW, 808 nm), were applied vertically at the center of stirring raw materials. The samples were sintered at $1000^{\circ}C$ for 2, 4, and 6 h. X-ray diffraction (XRD) analysis showed that samples prepared under the green laser have the highest purity. The FT-IR spectra showed that the stretching and bending vibrations of TiO bond without any other bonds, which are compatible to the X-ray diffraction (XRD) results. Samples were characterized by transmission electron microscopy (TEM), Scan electron microscopy (SEM), and UV-Visible spectrophotometer. Characterization showed the samples prepared under the green laser to have the highest particle size (~ 50 nm) and transparency for all sintering durations. Laser beam effects on electrical characterization were studied. BT nanoparticles prepared under the green laser show the higher dielectric constant, which was found to increase with sintering temperature.

• Journal of the Korean Ceramic Society
• /
• v.46 no.2
• /
• pp.146-154
• /
• 2009

It is necessary to minimize the thickness of Ni inner electrode layer and to improve the coverage of inner electrode, for the purpose of developing the ultra high-capacity multi layered ceramic capacitor (MLCC). Thus, low temperature sintering of dielectric $BaTiO_3$ ceramic should be precedently investigated. In this work, the relationship between dielectric properties of MLCC and batch condition such as mixing and milling methods was investigated in the $BaTiO_3$(BT)-Dy-Mg-Ba system with borosilicate glass as a sintering agent. In addition, several chip properties of MLCC manufactured by low temperature sintering were compared with conventionally manufactured MLCC. It was found that low temperature sintered MLCC showed better DC-bias property and lower aging rate. It was also confirmed that the thickness of Ni inner electrode layer became thinner and the coverage of inner electrode was improved through low temperature sintering.

• Journal of the Korean Ceramic Society
• /
• v.39 no.2
• /
• pp.159-163
• /
• 2002

A single phase perovskite relaxor ferroelectric PMN-PT-BT was prepared by a single calcination and the modified mixed oxide process. It was accomplished by ball-milling PbO, $Nb_2O_5,\;Ti(OC_3H_7)_4,\;BaCO_3,\;and\;Mg(NO_3)_2$ instead of MgO, removing the solvent, and then followed by calcination at 900$^{\circ}C$ for 2h. The specimen sintered at 1100$^{\circ}C$/2h showed the sintered density of 7.83 g/$cm^3$, room temperature dielectric constant of 22000, and dielectric loss of 2.5%. Addition of 1.0 mole% (0.3 wt%) of Ag as $AgNO_3$ and followed by calcination at 550$^{\circ}C$/2h lowered the sintering temperature to 900$^{\circ}C$. It still showed the sintered density of 7.88 g/$cm^3$, room temperature dielectric constant of 20000 and dielectric loss of 2.4%.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1992.11a
• /
• pp.42-45
• /
• 1992

In this study, the structural, dielectric and electrical properties of $0.85Pb(Zn_{1/3}Nb_{2/3})O_3-0.1BaTiO_3-0.05PbTiO_3$ ceramics were investigated with respect to the variations of $La_2O_3$ addition amount. The specimen with 0.2 [wt%] $La_2O_3$ addition amount, which has the coupling constants with the value of $k_p$=44.8[%]. $k_{31}$=25.4[%] and the piezoelectric constant with $d_{31}=100{\times}10^{-12}$[C/N] respectively, exhibits the relatively good values in the applications of electrostriction actuators.