• Journal of the Korean institute of surface engineering
• /
• v.43 no.5
• /
• pp.238-242
• /
• 2010

In the present work, the influence of oxide on the Cr-Si-N coatings was investigated for the Cr-Si-O-N coatings on AISI 304 and Si wafer deposited by hybrid system, which combines the DC magnetron sputtering technique and arc ion plating (AIP) using Cr and Si target in an $Ar/N_2/O_2$ gaseous mixture. As the O content in the Cr-Si-N coatings increased, the diffraction patterns of the Cr-Si-O-N coatings showed CrN and $Cr_2O_3$ phases. However, as the O content increased to 28.8 at.%, diffraction peak of $Cr_2O_3$ was disappeared in the Cr-Si-O-N coating. The $d_{200}$ value was decreased with increasing of O content. The average grain size increased from about 40 nm to 65 nm as the O content increased. The maximum micro-hardness of the Cr-Si-O-N coating was obtained 4507 Hk at the O content of 24.8 at.%. The average friction coefficient of the Cr-Si-O-N coatings was gradually decreased by increasing the O content and the average friction coefficient decreased from 0.37 to 0.25 by increasing the O content. These results indicated that amorphous phase was increased in the Cr-Si-O-N coatings by increasing of O content.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.577-577
• /
• 2013

플라즈마를 이용하는 공정은 반도체 산업에서 박막트랜지스터, 평면 모니터와 LCD 등 다양한 반도체 및 디스플레이 소자를 제작하는데 중요한 기술 중 하나로 발전되어 왔다. 현재 플라즈마 공정 기술을 이용하여 소자의 크기를 수십 나노 이하로 공정함으로써 수율을 향상시킬 수 있었지만, 소자의 미세화는 그 한계점에 봉착하였다. 그러한 이유로 웨이퍼 사이즈의 크기를 대구경화 시킴으로써 이런 문제점을 극복하고자 하였지만, 대구경 웨이퍼 사이즈에 맞는 차세대 대면적 공정 장비와 그에 따른 플라즈마 소스의 개발과 이를 컨트롤 할 수 있는 능력이 매우 절실하게 되었다. 본 연구에서는 대구경 웨이퍼용 플라즈마 소스를 위해 상대적으로 낮은 압력과 고밀도 플라즈마를 발생시킬 수 있는 유도 결합형 플라즈마원을 사용하였다. 하지만 유도 결합형 플라즈마 소스의 경우 대구경화에 따른 안테나의 길이가 길어짐으로써 생기는 정상파 효과를 피할 수가 없게 되었다. 그러한 이유로, 본 연구에서는 정상파 효과를 줄일 수 있는 상대적으로 낮은 주파수를 사용하는 안테나의 형태를 이용하여 실질적인 공정 영역에 있어서의 균일도 문제를 해결하였다. 또한, 플라즈마의 특성조절을 위해 이중주파수를 사용함 으로써 플라즈마 특성 조절을 하였다. 이러한 형태의 이중주파수를 사용하는 플라즈마 소스를 이용하여 10 mTorr의 Ar/CF4 조건에서 양이온 종들을 PSM (Plasma Sampling Mass spectroscopy, HIDEN Inc.)을 통해 에너지를 분석하였다. 이중 주파수에 있어 전력비율에 따라 IEDs (Ion Energy Distributions)는 많은 변화가 관찰되었으며, 인가하는 입력전력에 따라 E-H mode 전이가 일어남을 관찰할 수 있었다.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.187-192
• /
• 2008

Multi-walled carbon nanotube (MWNT)/$SnO_2$ nano-composite (MSC) for the anode electrode of a Li-ion battery was prepared using a homogeneous precipitation method with $SnCl_2$ precursors in the presence of MWNT. XRD results indicate that when annealed in Ar at $400^{\circ}C$, $Sn_6O_4(OH)_4$ was fully converted to $SnO_2$ phases. TEM observations showed that most of the $SnO_2$ nanoparticles were deposited directly on the outside surface of the MWNT. The electrochemical performance of the MSC electrode showed higher specific capacities than a MWNT and better cycleability than a nano-$SnO_2$ electrode. The electrochemical performance of the MSC electrode improved because the MWNT in the MSC electrode absorbed the mechanical stress induced from a volume change during alloying and de-alloying reactions with lithium, leading to an increase in the electrical conductivity of the composite material.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.205-205
• /
• 2010

투명 전극(transparent conducting oxide, TCO)은 높은 전기전도도 및 낮은 비저항 ($10^{-4}{\sim}10^{-3}\;{\Omega}cm$)과 가시광영역에서의 우수한 광투과도(> 80%) 특성을 가지며, 주로 디스플레이, 태양전지, 가스 센서 소자 등에 쓰인다. 투명전극으로 쓰이는 대표적인 물질로서는 ITO, ZnO, $SnO_2$ 등이 있으며, ITO는 전기적 특성이 우수하여 널리 사용되고 있으나 가격이 비싸고 화학적으로 불안정하고, ZnO는 ITO에 비해 가격이 저렴하지만 고온에서 불안정한 특성을 가지고 있다. 반면, $SnO_2$는 ITO와 ZnO에 비해 전기적 특성은 떨어지지만, 우수한 열적, 화학적 안정성 및 높은 내마모성을 가지고 제조단가가 저렴하여 TCO 재료로 많은 연구가 진행되고 있다. TCO 박막을 증착시키는 방법으로 CVD, ion plating, sputtering, spray pyrolysis 등이 있으며, 이 중 sputtering 방법은 균일한 입자로 균질의 박막을 입힐 수 있고 우수한 재현성과 낮은 온도에서도 증착이 가능하여 박막 제조 방법으로 널리 이용되고 있다. 본 연구에서는 $SnO_2$ 박막을 실리콘 (100) 및 글라스 (Eagle 2000) 기판 위에 RF magnetron sputtering 방법을 사용하여 제작하였다. 박막 증착을 위해 99.99%의 2 인치 un-doped $SnO_2$ 타겟을 사용하였고, 기판은 20 rpm 으로 회전시켜 균일한 박막이 형성될 수 있도록 하였으며, 초기 진공도는 $1{\times}10^{-6}\;Torr$가 되도록 하였다. 증착 변수로 기판-타겟간 거리, RF 파워, $O_2/(Ar+O_2)$ 비, 공정압력, 기판 온도 등을 각각 변화 시키며 $SnO_2$ 박막을 증착하였다. 증착된 박막의 구조적 및 광학적 특성을 분석하기위해 FE-SEM, AFM, XRD, UV/VIS spectrophotometer, Photoluminescence 등을 사용하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.30 no.5 s.248
• /
• pp.413-421
• /
• 2006

The bubble dynamics induced by direct laser heating is experimentally analyzed as a first step to assess the technical feasibility of laser-based ink-jet technology. To understand the interaction between laser light and ink, the absorption spectrum is measured for various ink colors and concentrations. The hydrodynamics of laser-generated bubbles is examined by the laser-flash photography. When an Ar ion laser pulse (wavelength 488 nm) with an output power up to 600 mW is incident on the ink solution through a transparent window, a hemispherical bubble with a diameter up to ${\sim}100{\mu}m$ can be formed with a lifetime in a few tens of microsecond depending on the laser power and the focal-spot size. Parametric study has been performed to reveal the effect of laser pulse width, output power, ink concentration, and color on the bubble dynamics. The results show that the bubble generated by a laser pulse is largely similar to that produced by a thin-film heater. Consequently, the present work demonstrates the feasibility of developing a laser-actuated droplet generation mechanism for applications in ink-jet print heads. Furthermore, the results of this work indicate that the droplet generation frequency is likely to be further increased by optimizing the process parameters.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.11
• /
• pp.191-198
• /
• 2000

Laser direct patterning of the coated photoresist (PMER-NSG31B) layer was studied to make halftone dots on gravure printing roll. The selective laser hardening of photoresist by Ar-ion laser(wavelength: 333.6~363.8nm) was controlled by the A/O modulator. The coating thickness in the range of 5~11$\mu m$ could be obtained by using the up-down directional moving device along the vertically located roll. The width, thickness and hardness of the hardened lines formed under the laser power of 200~260㎽ and irradiation time of 4.4~6.6 $\mu$sec/point were investigated after developing. The hardened width increased as the coating thickness increased. Though the hardened thickness was changed due to the effect of the developing solution, the hardened layer showed good resistance to the scratching of 2H pencil. Also, the hardened minimum line widths of 10$\mu m$ could be obtained. The change of line width was also found after etching, and the minimum line widths of 6$\mu m$ could be obtained. The hardened lines showed the good resistance to the etching solution. Finally, the experimental data could be applied to make gravure halftone dots using the developed imaging process, successfully.

• Journal of the Korean Vacuum Society
• /
• v.22 no.5
• /
• pp.238-244
• /
• 2013

Doping process using laser is an important process in fabrication of solar cell for heat treatment. However, the process of using the furnace is difficult to form a selective emitter doping region. The case of using a selective emitter laser doping is required an expensive laser equipment and induce the wafer's structure damage due to high temperature. This study, we fabricated a new costly plasma source. Through this, we research the selective emitter doping. We fabricated that the atmospheric pressure plasma jet injected Ar gas is inputted a low frequency (a few tens kHz). We used shallow doping wafers existing PSG (Phosphorus Silicate Glass) on the shallow doping CZ P-type wafer. Atmospheric plasma treatment time was 15 s and 30 s, and current for making the plasma is 40 mA and 70 mA. We investigated a doping profile by using SIMS (Secondary Ion Mass Spectroscopy) and we grasp the sheet resistance of electrical character by using doping profile. As result of experiment, prolonged doping process time and highly plasma current occur a deeper doping depth, moreover improve sheet resistance. We grasped the wafer's surface damage after atmospheric pressure plasma doping by using SEM (Scanning Electron Microscopy). We check that wafer's surface is not changed after plasma doping and atmospheric pressure doping width is broaden by increase of plasma treatment time and current.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.157-157
• /
• 2015

Recently, the growing interest in organic microelectronic devices including OLEDs has led to an increasing amount of research into their many potential applications in the area of flexible electronic devices based on plastic substrates. However, these organic devices require a gas barrier coating to prevent the permeation of water and oxygen because organic materials are highly susceptible to water and oxygen. In particular, high efficiency OLEDs require an extremely low water vapor transition rate (WVTR) of $1{\times}10^{-6}g/m^2day$. The Key factor in high quality inorganic gas barrier formation for achieving the very low WVTR required ($1{\times}10^{-6}g/m^2day$) is the suppression of defect sites and gas diffusion pathways between grain boundaries. In this study NBAS process was introduced to deposit enhanced film density single gas barrier layer with a low WVTR. Fig. 1. shows a schematic illustration of the NBAS apparatus. The NBAS process was used for the $Al_2O_3$ nano-crystal structure films deposition, as shown in Fig. 1. The NBAS system is based on the conventional RF magnetron sputtering and it has the electron cyclotron resonance (ECR) plasma source and metal reflector. $Ar^+$ ion in the ECR plasma can be accelerated into the plasma sheath between the plasma and metal reflector, which are then neutralized mainly by Auger neutralization. The neutral beam energy is controlled by the metal reflector bias. The controllable neutral beam energy can continuously change crystalline structures from an amorphous phase to nanocrystal phase of various grain sizes. The $Al_2O_3$ films can be high film density by controllable Auger neutral beam energy. we developed $Al_2O_3$ high dense barrier layer using NBAS process. We can verified that NBAS process effect can lead to formation of high density nano-crystal structure barrier layer. As a result, Fig. 2. shows that the NBAS processed $Al_2O_3$ high dense barrier layer shows excellent WVTR property as a under $2{\times}10^{-5}g/m^2day$ in the single barrier layer of 100nm thickness. Therefore, the NBAS processed $Al_2O_3$ high dense barrier layer is very suitable in the high efficiency OLED application.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.681-686
• /
• 1994

Microwave Detector Using $YBa_{2}Cu_{3}O_{7-x}$, Grain Boundary Junction $YBa_{2}Cu_{3}O_{7-x}$ superconductor thin films were deposited on $LaAIO_{3}$ (100) single crystal substrates using a metal organic chemical vapor deposition (MOCVD) method. These films showed the critical temperature of about 9OK and critical current density of over $10^5/A \textrm{cm}^2$at 77K. These films showed granular structure with 0.5~1.5$\mu \textrm{m}$ grains. Bridge-type junctions, 6$\mu \textrm{m}$ in width and 6pm in length, were fabricated using the photolithography and the Ar ion milling techniques. Current-voltage (I-V) characteristics of these junctions with the microwave irradiation at 77K were studied. The critical current densities decreased as the irradiated microwave power increased. When microwaves were irradiated on the bridge at 77K. the I-V charateristics showed constant voltage stcp(Shapiro steps) at $\Delta$=nho/2e.

• Journal of Food Hygiene and Safety
• /
• v.23 no.3
• /
• pp.218-221
• /
• 2008

The levels of sulfites in wooden chopsticks were analyzed using two different methods, distillation-alkali titration and ion chromatography. According to the two methods, Sulfur dioxide($SO_2$) was validated by 0.6 and 0.2 ${\mu}ml$ of limit of detection(LOD), 1.8 and 0.5 ${\mu}ml$ of limit of quantification, (LOQ) and a $R^2>0.998$ for linearity, respectively. The recoveries of $SO_2$ from food simulants spiked ar levels of 100 ppm were 70.2-100.2%. 158 samples of wooden chopsticks were monitored the migrated amounts of sulfites. Sulfites were detected in 30 samples in ranged of 0.6 to 15.5 ppm. Maximum migration level, 15.5 ppm of sulfites was considered giving no harmful effect to human since it was reached 5.5% of estimated SML.