• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.05b
• /
• pp.12-16
• /
• 2001

We investigated the etching characteristics of $YMnO_3$ thin films in high-density plasma etching system. In this study. $YMnO_3$ thin films were etched with $CF_{4}/Ar$ gas chemistries in inductively coupled plasma (ICP). Etch rates of $YMnO_3$ were measured according to gas mixing ratios. The maximum etch rate of $YMnO_3$ is 18 nm/min at $CF_{4}/(CF_{4}+Ar)$ of 20%. In optical emission spectroscopy (OES) analysis, F radical and Ar* ions in plasma at various gas chemistries decreased with increasing $CF_4$ content. Chemical states of $YMnO_3$ films exposed in plasma were investigated with x-ray photoelectron spectroscopy (XPS) and secondary ion mass spectrometry (SIMS). There is a chemical reaction between metal (Y, Mn) and F and metal-fluorides were removed effectively by Ar ion sputtering. $YF_x$, $MnF_x$ such as YF, $YF_2$, $YF_3$ and $MnF_3$ Were detected using SIMS analysis. The etch slope is about $65^{\circ}C$ and free of residues.

• Journal of the Korean institute of surface engineering
• /
• v.45 no.5
• /
• pp.206-211
• /
• 2012

Process analysis was carried out during deposition of MgO by inductively coupled plasma assisted reactive magnetron sputtering in Ar and $O_2$ ambient. At the initiation of Mg sputtering with bipolar pulsed dc power in Ar ambient, total pressure showed sharp increase and then slow fall. To analyse partial pressure change, QMS was used in downstream region, where the total pressure was maintained as low as $10^{-5}$ Torr during plasma processing, good for ion source and quadrupole operation. At base pressure, the major impurity was $H_2O$ and the second major impurity was $CO/N_2$ about 10%. During sputtering of Mg in Ar, $H_2$ soared up to 10.7% of Ar and remained as the major impurity during all the later process time. When $O_2$ was mixed with Ar, the partial pressure of Ar decreased in proportion to $O_2$ flow rate and that of $H_2$ dropped down to 2%. It was understood as Mg target surface was oxidized to stop $H_2$ emission by Ar ion sputtering. With ICP turned on, the major impurity $H_2$ was converted into $H_2O$ consuming $O_2$ and C was also oxidized to evolve CO and $CO_2$.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.87-90
• /
• 1999

We have studied the annealing effects of 570 (SrTiO$_3$) single crystal substrate and the I-V properties of step-edge junctions after Ar ion milling. YBa$_2Cu_3O_7$ (YBCO) thin films are fabricated on the substrates by using pulsed laser deposition (PLD) and photolithography. The surface of Ar ion milled substrate was characterized with atomic force microscope (AFM) and scanning electron microscope (SEM) images. After the substrate was damaged by milling, the critical current density of YBCO thin films deposited on the substrate was lowered. The annealing of the damaged substrate at about 1000 $^{\circ}C$ recovered the critical current density to that before the milling. Futhermore the annealing helped junction formation due to high quality film and increased the yield rate for the fabrication of high quality step-edge junction.

• Bulletin of the Korean Chemical Society
• /
• v.28 no.8
• /
• pp.1341-1345
• /
• 2007

The surface chemistry of D2O dosed Zircaloy-4 (Zry-4) surface followed by Ar-ion bombardment and annealing was studied by means of X-ray photoelectron spectroscopy (XPS) and Ultraviolet photoelectron spectroscopy (UPS). In the XPS study, Ar-ion bombardment caused decrease of the oxygen on the surface region of Zry-4 and therefore led to change the oxidation states of the zirconium from oxide to metallic form. In addition, oxidation states of zirconium were changed to lower oxidation states of zirconium due to depopulation of oxygen on the surface region by annealing. Up to about 787 K, the bulk oxygen diffused out to the subsurface region and after this temperature, the oxygen on the surface of Zry-4 was depopulated. UPS study showed that the valence band spectrum of the D2O exposed Zry-4 exhibited a dominant peak at around 13 eV and no clear Fermi edge was detected. After stepwise Ar+ sputtering processes, the decrease of the oxygen on the surface of Zry-4 led to suppress the dominant peak around 13 eV, the peak around 9 eV and develop a new peak of the metallic Zr 4d state (20.5-21.0 eV) at the Fermi level.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.11 no.5
• /
• pp.231-237
• /
• 2001

Etch rates up to 120 nm/min for $Ta_{2}O_{5}$ were achieved in both $SF_{6}/Ar$ and $Cl_{2}/Ar$ discharges. The effect of ultraviolet (UV) light illumination during ICP etching on $Ta_{2}O_{5}$ etch rate in those plasma chemistries was examined and UV illumination was found to produce significant enhancements in $Ta_{2}O_{5}$ etch rates most likely due to photoassisted desorption of the etch products. The effects of ion flux, ion energy, and plasma composition on (Ba, Sr)$TiO_3$ etch rate were examined and maximum etch rate ~90 nm/min was achieved in $Cl_{2}/Ar$ ICP discharges while $CH_{4}/H_{2}/Ar$ chemistry produced extremely low etch rates (${\leq}10\;nm/min$) under all conditions.

• Journal of the Korean Vacuum Society
• /
• v.2 no.4
• /
• pp.468-473
• /
• 1993

Damages on Si substrate induced by Ar ion implantation and it annealing behavior during rapid thermal annealing were investigated by the cross-sectional TEM (transmissin electron microscopy), RB(Rutherfordbackscattering) spectra an dthermal wave (TW) modulation reflectance methods. Continuous amorphous layer extending to the surface were generated by Ar ion implantation for higher doses than 1 $\times$1015cm-2. The recrystallization of the amorphous layer prodeeded as the annealing temperature increased . However the amorphous /crystal interfacial undulations caused the micro twins and damage clusters. Damage clusters generated by lower doses than 1 $\times$1015 cm-2 disappeared slowly as the annealing temperature increased, but even at 110$0^{\circ}C$ a few damage clusters still remained.

• Korean Journal of Optics and Photonics
• /
• v.13 no.3
• /
• pp.204-208
• /
• 2002

We investigate the dependence of indium tin oxide (ITO) thin films on the mixing ratio of Ar:O$_2$ produced by an ion-gun and $O_2$ injected inside the divergence angle of the ion-beam to optimize their sheet resistance and transmittance. The substrate is placed outside the divergence angle, and the films are grown by ion mixing with ITO evaporated at room temperature. From the XRD measurement ITO films are found to be amorphous. ITO thin films show the highest transmittance of 85% at 3$\times$10$^{-5}$ Torr of 0$_2$ and Ae:O$_2$ ratio of 40:60, and the smallest sheet resistance of 132 $\Omega$/$\square$at 1$\times$10$^{-5}$ Torr of $O_2$ and As:O$_2$ ratio of 40:60.

• Journal of the Semiconductor & Display Technology
• /
• v.20 no.4
• /
• pp.72-77
• /
• 2021

The radial distribution of etch rate was analyzed using the ion energy flux model in VHF-CCP. In order to exclude the effects of polymer passivation and F radical depletion on the etching. The experiment was performed in Ar/SF6 plasma with an SF6 molar ratio of 80% of operating pressure 10 and 20 mTorr. The radial distribution of Ar/SF6 plasma was diagnosed with RF compensated Langmuir Probe(cLP) and Retarding Field Energy Analyzer(RFEA). The radial distribution of ion energy flux was calculated with Bohm current times the sheath voltage which is determined by the potential difference between the plasma space potential (measured by cLP) and the surface floating potential (by RFEA). To analyze the etch rate uniformity, Si coupon samples were etched under the same condition. The ion energy flux and the etch rate show a close correlation of more than 0.94 of R² value. It means that the etch rate distribution is explained by the ion energy flux.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.146-150
• /
• 2000

Two methods have been investigated to fabricate good quality step-edge Josephson junctions on STO, MgO, and LAO single crystal substrates. One is the annealing of substrates at 1050$^{\circ}$C in 1 atmospheric oxygen after Ar-ion milling. The other is the cleaning of step-edge by using Ar ion milling. The step-edge is characterized with atomic force microscope (AFM) images. And YBCO thin films are deposited by using pulsed laser. The I-V properties of step-edge junctions are characterized. The yield rate of step-edge junction is increased by new fabrication methods.

• Journal of the Korean Vacuum Society
• /
• v.12 no.S1
• /
• pp.63-66
• /
• 2003

It is experimentally shown that a $TiO_2$ film on Si(111) substrate was prepared by using the technique of D.C. reaction sputter deposition with $Ar^{+}$ ion beam bombardment, and a layer-like structure was observed from the depth profile of the interface between $TiO_2$ film and Si substrate with Scanning Electron Microscopy and Electron Probe. It was also surprisingly discovered that Ti atoms could be detected at about 9 $\mu$m depth. The $TiO_2$-Si interface bombarded by $Ar^{+}$ ion beams revealed multi-layer structures, a mechanism might be caused by defect diffusion, impurity and matrix relocation. Multi-relocations of impurity and matrix atoms were as a result of profile broadening of the $TiO_2$-Si interface, and the spread due to matrix relocation in this system is shown to exceed much more the spread due to impurity relocation.