• Journal of Advanced Marine Engineering and Technology
• /
• v.24 no.6
• /
• pp.61-69
• /
• 2000

Indium-Tin Oxide (ITO) films were prepared on the commercial glass substrate by the Magnetron Sputtering method. The target was a 90wt.% $In_2O_3$-10wt.% $SnO_2$with 99.99% purity. The ITO films deposited by changing the partial pressure of oxygen gas ($O_2$/(Ar+$O_2$)) of 2, 3 and 5% as well as by changing the substrate temperature of $300^{\circ}C$ or $500^{\circ}C$. The influence of substrate pre-annealing and pre-cleaning on the quality of ITO film were examined, in which the substrate temperature was $500^{\circ}C$ and oxygen partial pressure was 3%. The characteristics of films were examined by the 4-point probe, Hall effect measurement system, SEM, AFM, Spectrophotometer, and X-ray diffraction. The optimum ITO films have been obtained when the substrate temperature is $500^{\circ}C$ and oxygen partial pressure is 3%. At optimum condition, the film showed transmittance of 81%, sheet resistivity of $226\Omegatextrm{cm}^2$, resistivity($\rho$) of $5.4\times10^{-3}\Omega$cm, carrier concentration of $1.0\times10^{19}cm^{-3}$, and carrier mobility of $150textrm{cm}^2$Vsec. From XRD spectrum, c(222) plane was dominant in the case of substrate temperature at $300^{\circ}C$, without regarding to oxygen partial pressure. However, in the case of substrate temperature at $500^{\circ}C$, c(400) plane was grown together with c(222) plane, only for oxygen partial pressure of 2 and 3%. In both case of chemical and ultrasonic cleaning without pre-annealing the substrate, it showed much almost same sheet resistivity, resistivity($\rho$), transmittance, carrier concentration, and carrier mobility. In case of $500^{\circ}C$/60min pre-annealing before ITO film deposited, both transimittance and carrier mobility are better than no pre-annealing, because pre-annealing is supposed to remove alkari ions diffusion from substrate. ITO film deposited on the Corning 0080 sybstrate showed a little bit better sheet resistivity, resistivity($\rho$), transimittance, carrier concentration than the film deposited on commercial glass. But no differences between Corning substrate and pre-annealed commercial glass substrate are found.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.163-163
• /
• 2010

중적외선 영역 ($3{\sim}5\;{\mu}m$)은 공기 중에 존재하는 이산화탄소나 수증기에 의해 흡수가 일어나지 않기 때문에 군사적으로 중요한 파장 영역이며, 야간에 적을 탐지하는데 응용되고 있다. InSb는 77 K에서 중적외선 파장 흡수에 적합한 밴드갭 에너지 (0.228 eV)를 갖고 있으며, 다른 화합물 반도체와 달리 전하 수송자 이동도 (전자: $10^6\;cm^2/Vs$, 정공: $10^4\;cm^2/Vs$)가 매우 빠르기 때문에 적외선 화상 감지기 재료로 매우 적합하다. 또한 현재 중적외선 영역대에서 널리 사용되는 HgCdTe (MCT)와 대등한 소자 성능을 나타냄과 동시에 낮은 기판 가격, 소자의 제작 용이성 때문에 MCT를 대체할 물질로 주목 받고 있다. 하지만, 기판과 절연막의 계면에 존재하는 결함 때문에 에너지 밴드갭 내에 에너지 준위를 형성하여 높은 누설 전류 특성을 보인다. 따라서 InSb 적외선 소자의 구현을 위하여 고품질의 절연막의 연구가 필수적이라고 할 수 있겠다. 절연막의 특성을 알아보기 위해, n형 InSb 기판에 플라즈마 화학 기상 증착법 (PECVD)을 이용하여 $SiO_2$, $Si_3N_4$를 증착하였으며, 증착 온도를 $120^{\circ}C$에서 $240^{\circ}C$까지 $40^{\circ}C$ 간격으로 변화하여 증착온도가 미치는 영향에 대하여 알아보았다. 절연막과 기판의 계면 특성을 분석하기 위하여 77 K에서 커패시턴스-전압 (C-V) 분석을 하였으며, 계면 트랩 밀도는 Terman method를 이용하여 계산하였다 [1]. $Si_3N_4$를 증착하였을 경우, $120{\sim}240^{\circ}C$의 증착 온도에서 $2.4{\sim}4.9{\times}10^{12}\;cm^{-2}eV^{-1}$의 계면 트랩 밀도를 가졌으며, 증착 온도가 증가할수록 계면 트랩 밀도가 증가하는 경향을 보였다. 또한 모든 증착 온도에서 flat band voltage가 음의 전압으로 이동하였다. $SiO_2$의 경우 $120{\sim}200^{\circ}C$의 증착온도에서 $7.1{\sim}7.3{\times}10^{11}\;cm^{-2}eV^{-1}$의 계면 트랩 밀도 값을 보였으나, $240^{\circ}C$ 이상에서 계면 트랩밀도가 $12{\times}10^{11}\;cm^{-2}eV^{-1}$로 크게 증가하였다. $SiO_2$ 절연막을 사용함으로써, $Si_3N_4$ 대비 약 25% 정도 낮은 계면 트랩 밀도를 얻을 수 있었으며, 모든 증착 온도에서 양의 전압으로 flat band voltage가 이동하였다. 두 절연막에 대한 계면 트랩의 원인을 분석하기 위하여 XPS 측정을 진행하였으며, 깊이에 따른 조성 분석을 하였다. 본 실험에서 최적화된 $SiO_2$ 절연막을 이용하여 InSb 소자의 pn 접합 연구를 진행하였다. Be+ 이온 주입을 진행하고, 급속열처리(RTA) 공정을 통하여 p층을 형성하였다. -0.1 V에서 16 nA의 누설 전류 값을 보였으며, $2.6{\times}10^3\;{\Omega}\;cm^2$의 RoA (zero bias resistance area)를 얻을 수 있었다.

• Korean Journal of Materials Research
• /
• v.20 no.12
• /
• pp.654-660
• /
• 2010

The influences of Na and K content on the crystal phase, the microstructure and the electrical property of $BaTiO_3$-based thermistors was found to show typical PTC effects. The crystal phase of powder calcined at $1000^{\circ}C$ for 4hrs showed a single phase with $BaTiO_3$, and the crystal structure was transformed from tetragonal to cubic phase according to added amounts of Na and K. In XRD results at $43^{\circ}\sim47^{\circ}$, the $(Ba_{0.858}Na_{0.071}K_{0.071})(Ti_{0.9985}Nb_{0.0015})O_{3-\delta}$ showed (002) and (200) peaks but the $(Ba_{0.762}Na_{0.119}K_{0.119})(Ti_{0.9975}Nb_{0.0025})O_{3-\delta}$ showed (002), (020) and (200) peaks. In sintered bodies, those calcined at $600^{\circ}C$ rather than at $1000^{\circ}C$ were dense, and for certain amounts of Na and K showed rapid decreases in grain size. In relative permittivity, the curie temperature due to the transformation of ferroelectric phase rose with added Na and K but decreased in terms of relative permittivity. In the result of the R-T curve, the sintered bodies have curie temperatures of about $140^{\circ}C$ and the resistivity of sintered bodies have scores of $\Omega{\cdot}cm$; the jump order of sintered bodies was shown to be more than $10^4$ in powder calcined at $1000^{\circ}C$.

• Journal of Life Science
• /
• v.23 no.3
• /
• pp.341-346
• /
• 2013

The disappearance of seaweed flora in some rocky areas, which is known as algal whitening, barren ground, coralline flats, or deforested areas, is associated with some species of coralline algae. To determine the biological characteristics of a representative species of crustose coralline alga, the 18S rDNA gene was sequenced to identify the genus Lithophyllum. According to its morphological and distributional characteristics, it was deduced to be L. yessoense. Viability was measured using triphenyl tetrazolium chloride and showed high viability from December to February. Culture conditions of $16^{\circ}C$, a 16 hr light, 8 hr dark cycle, and 30 ${\mu}E/m^2/s$ light intensity were optimal for maintaining the viability of the alga for up to five days. Included in the fatty acids was 9.7% ${\omega}$-3 eicosapentaenoic acid. An electron microscopy scan of the surface structure revealed round craters about 3.6 ${\mu}m$ in diameter, which were covered with rough, irregular, and angular polygon-shaped structures about 1.0 to 3.7 ${\mu}m$ in size. Based on the composition and structure found in our study, biomimetic coralline alga might become an environmentally friendly antifouling material against the attachment of soft foulants.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.37 no.3
• /
• pp.196-213
• /
• 2001

A split beam ultrasonic transducer operating at a frequency of 70 kHz to use in the fish sizing echo sounder was developed and the acoustic radiation characteristics were experimentally analyzed. The amplitude shading method utilizing the properties of the Chebyshev polynomials was used to obtain side lobe levels below -20 dB and to optimize the relationship between main beam width and side lobe level of the transducer, and the amplitude shading coefficient to each of the elements was achieved by changing the amplitude contribution of elements with 4 weighting transformers embodied in the planar array transducer assembly. The planar array split beam transducer assembly was composed of 36 piezoelectric ceramics (NEPEC N-21, Tokin) of rod type of 10 mm in diameter and 18.7 mm in length of 70 kHz arranged in the rectangular configuration, and the 4 electrical inputs were supplied to the beamformer. A series of impedance measurements were conducted to check the uniformity of the individual quadrants, and also in the configurations of reception and transmission, resonant frequency, and the transmitting and receiving characteristics were measured in the water tank and analyzed, respectively. The results obtained are summarized as follows : 1. Average resonant and antiresonant frequencies of electrical impedance for four quadrants of the split beam transducer in water were 69.8 kHz and 83.0 kHz, respectively. Average electrical impedance for each individual transducer quadrant was 49.2$\Omega$ at resonant frequency and 704.7$\Omega$ at antiresonant frequency. 2. The resonance peak in the transmitting voltage response (TVR) for four quadrants of the split beam transducer was observed all at 70.0 kHz and the value of TVR was all about 165.5 dB re 1 $\mu$Pa/V at 1 m at 70.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The resonance peak in the receiving sensitivity (SRT) for four combined quadrants (quad LU+LL, quad RU+RL, quad LU+RU, quad LL+RL) of the split beam transducer was observed all at 75.0 kHz and the value of SRT was all about -177.7 dB re 1 V/$\mu$Pa at 75.0 kHz with bandwidth of 10.0 kHz between -3 dB down points. The sum beam transmitting voltage response and receiving senstivity was 175.0 dB re 1$\mu$Pa/V at 1 m at 75.0 kHz with bandwidth of 10.0 kHz, respectively. 3. The sum beam of split beam transducer was approximately circular with a half beam angle of $9.0^\circ$ at -3 dB points all in both axis of the horizontal plane and the vertical plane. The first measured side lobe levels for the sum beam of split beam transducer were -19.7 dB at $22^\circ$ and -19.4 dB at $-26^\circ$ in the horizontal plane, respectively and -20.1 dB at $22^\circ$ and -22.0 dB at $-26^\circ$ in the vertical plane, respectively. 4. The developed split beam transducer was tested to estimate the angular position of the target in the beam through split beam phase measurements, and the beam pattern loss for target strength corrections was measured and analyzed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.9
• /
• pp.1602-1608
• /
• 2007

The composites were fabricated, respectively, using 61[vol.%] SiC-39[vol.%] $TiB_2$ and using 61[vol.%] SiC-39[vol.%] $ZrB_2$ powders with the liquid forming additives of 12[wt%] $Al_2O_3+Y_2O_3$ by hot pressing annealing at $1650[^{\circ}C]$ for 4 hours. Reactions between SiC and transition metal $TiB_2$, $ZrB_2$ were not observed in this microstructure. The result of phase analysis of composites by XRD revealed SiC(6H, 3C), $TiB_2$, $ZrB_2$ and $YAG(Al_5Y_3O_{12})$ crystal phase on the Liquid-Phase-Sintered(LPS) $SiC-TiB_2$, and $SiC-ZrB_2$ composite. $\beta\rightarrow\alpha-SiC$ phase transformation was occurred on the $SiC-TiB_2$ and $SiC-ZrB_2$ composite. The relative density, the flexural strength and Young's modulus showed the highest value of 98.57[%], 249.42[MPa] and 91.64[GPa] in $SiC-ZrB_2$ composite at room temperature respectively. The electrical resistivity showed the lowest value of $7.96{\times}10^{-4}[\Omega{\cdot}cm]$ for $SiC-ZrB_2$ composite at $25[^{\circ}C]$. The electrical resistivity of the $SiC-TiB_2$ and $SiC-ZrB_2$ composite was all positive temperature coefficient resistance (PTCR) in the temperature ranges from $25[^{\circ}C]$ to $700[^{\circ}C]$. The resistance temperature coefficient of composite showed the lowest value of $1.319\times10^{-3}/[^{\circ}C]$ for $SiC-ZrB_2$ composite in the temperature ranges from $100[^{\circ}C]$ to $300[^{\circ}C]$ Compositional design and optimization of processing parameters are key factors for controlling and improving the properties of SiC-based electroconductive ceramic composites.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.33 no.8
• /
• pp.1337-1342
• /
• 2004

To improve the quality of Gulbi, 10% garlic juice (GJ), 10% onion juice (OJ), and 10% garlic and onion juice mixture (GOJ) were added to the brine solution as a wet-salting method. The changes of total volatile basic nitrogen (TVB-N) and trimethyl amine (TMA) production, thiobarbituric acid reactive substance (TBARS) value, and total microbial numbers in Gulbi were analyzed during storage at room temperature for 12 days. The group treated with 10% GOJ showed the lowest values of 88.2 mg/l00 g in TVB-N, 14.13 mg/l00 g in TMA, and 3.1 $\mu$mol/kg in TBARS. The fatty acid profile of Gulbi was analyzed on 5, 15, and 30 days to investigate the effect of GOJ treatment. The group treated with GOJ showed higher C22:6 (9.91%) and C20:5 (4.25%) contents than control (7.37% and 3.71%, respectively), but had lower C18:1 (24.44%) content. The saturated fatty acid content in Gulbi was 32∼35% and the C16:0 (21∼23%) was predominant in it. Oleic acid was major unsaturated fatty acid in Gulbi. The contents of polyunsaturated fatty acids (C18:3, C20:5, C22:6) were decreased after 30 days but increased the saturated fatty acid (C16:0) and monoenes (C16:1 and C18:1). The Gulbi treated with GOJ by brine salting method showed higher DHA and EPA (9.91% and 4.25%, respectively) contents than the control group.

• Asian-Australasian Journal of Animal Sciences
• /
• v.24 no.9
• /
• pp.1249-1255
• /
• 2011

This study examined the effect of CLA, flaxseed oil and fish oil and their combination forms on crude fat of liver and fatty acid profiles of liver, breast and thigh meat in broiler chicks. A total of 72, 1-day-old Cobb broilers were assigned to 6 groups, and fed an experimental diet supplemented with 5 different fat sources; conjugated linoleic acid (2% CLA), flaxseed oil (2% FXO), fish oil (2% FHO), CLA and flaxseed oil combination (1:1; 2% CXO), and CLA and fish oil combination (1:1; 2% CHO). Eight birds per treatment were processed, and liver, breast and thigh samples were investigated at 21 d of age. As a result of this study, most fatty acids of liver, breast and thigh meat were influenced by fat sources supplemented in the diet (p<0.05). CLA addition resulted in an increase of crude fat and saturated fatty acid (SFA) content but a concomitant decrease in n-3 to n-6 fatty acid ratio was observed in liver (p<0.05). Moreover, the same trends of SFA and n-3 to n-6 fatty acid ratio were also observed in breast and thigh meats of birds fed CLA alone. In the CXO-fed group or CHO-fed group, n-3 and n-3 to n-6 fatty acid ratio in both breast and thigh meat increased compared with CLA group, while SFA content decreased (p<0.05). FHO fed-groups had the lowest proportion of n-6 fatty acid in both breast and thigh meats compared to other fat source treatments (p<0.05). In conclusion, the increased levels of crude fat and SFA in liver and meats obtained by feeding CLA could be reduced by its combination with FXO or FHO. In addition, the combination of CLA and FXO or FHO fed to broiler chicks could increase the n-3 to n-6 fatty acid ratio of their meat along with the deposition of CLA.

• Journal of the Korean Electrochemical Society
• /
• v.11 no.2
• /
• pp.89-94
• /
• 2008

We synthesized and investigated $(La_{0.75}Sr_{0.25})_{1-x}FeO_{3-\delta}$ perovskite oxides having different stoichiomety (x = 0, 0.02, 0.04, 0.06, 0.08) as cathode materials. SEM images and XRD patterns reveal that the synthesized powder has uniform size distribution and high degree of crystallinity. The electrochemical performances of the synthesized powders were investigated by AC impedance spectroscopy. Both the electric conductivity and the electrochemical performance showed the highest properties at the stoichiometry x = 0.02. Finally, we concluded that the variation of A-site deficiency results in the variation of the amount of oxygen vacancy and micro structure, which leads to the variation of electric conductivity and polarization resistance.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2003.10a
• /
• pp.537-541
• /
• 2003

The a-Si:H TFTs using ferroelectric of SrTiO$_3$, as a gate insulator is fabricated on glass. Dielectric characteristics of ferroelectric is better than SiO$_2$, SiN. Ferroelectric increases ON-current, decreases threshold voltage of TFT and also breakdown characteristics. The a-Si:H deposited by PECVD shows absorption band peaks at wavenumber 2,000 $cm^{-1}$ /, 635 $cm^{-1}$ / and 876 $cm^{-1}$ / according to FTIR measurement. Wavenumber 2,000 $cm^{-1}$ /, 635 $cm^{-1}$ / are caused by stretching and rocking mode SiH1. The wavenumber of weaker band, 876 $cm^{-1}$ / is due to SiH$_2$ vibration mode. The a-SiN:H has optical bandgap of 2.61 eV, refractive index of 1.8 - 2.0 and resistivity of 10$^{11}$ - 10$^{15}$ aim respectively. Insulating characteristics of ferroelectric is excellent because dielectric constant of ferroelectric is about 60 - 100 and breakdown strength is over 1 MV/cm. TFT using ferroelectric has channel length of 8 - 20 $\mu$m and channel width of 80 - 200 $\mu$m. And it shows drain current of 3 $\mu$A at 20 gate voltages, Ion/Ioff ratio of 10$^{5}$ - 10$^{6}$ and Vth of 4 - 5 volts.