• Journal of Advanced Marine Engineering and Technology
• /
• v.28 no.6
• /
• pp.981-992
• /
• 2004

Freeze drying under vacuum condition is a complex process that involves simultaneous heat and mass transfer, sublimation of ice, and motion of sublimation front. Proper treatment of the motion of sublimation interface is crucial for an accurate prediction of the freeze drying process. Based on the enthalpy formulation that has been successfully used in liquid/solid phase change problems. a fixed grid method. streamlined for the freeze drying analysis. was developed in this study. The accuracy of the fixed grid method was checked by solving a one-dimensional tray freeze drying and a two-dimensional vial freeze drying problem and then comparing the results with those by the moving grid method. Finally. the freeze drying characteristics of two-dimensional slab and axis-symmetric cylinder was investigated using the fixed grid method.

• The KSFM Journal of Fluid Machinery
• /
• v.6 no.4 s.21
• /
• pp.21-28
• /
• 2003

CMP (Chemical Mechanical Polishing) is to achieve adequate local and global planarization for future sub-micrometer VLSI requirements. In designing CMP, numerical computation is quite helpful in terms of reducing the amount of experimental works. Stresses on pad, concentration of particles and particle tracking are studied for design. In this research, the optimization of grooved pad shape of CMP is performed through numerical investigation of slurry flow in CMP process. The result indicates that the combination of sinusoidal groove and skewed pad is the most optimal shape among the twenty candidates. Useful information can be obtained in velocity, pressure, stress, concentration of particles and particles trajectories, etc.

• Proceedings of the KIEE Conference
• /
• 2003.11b
• /
• pp.75-78
• /
• 2003

In this paper, a second-order 3-bit DSM using DWA(Data Weighted Averaging) algorithm is designed for bluetooth Zero-IF Receiver. The designed circuit has two integrators using a designed OTA, nonoverlapping two-phase clerk generator, 3-bit A/D converter, DWA algorithm and 3-bit D/A converter An ideal model of second-order lowpass DSM with a 3-bit quantizer was configured by using MATLAB, and each coefficients and design specification of each blocks were determined to have 10-bit resolution in 1MHz channel bandwidth. The designed second-order 3-blt lowpass DSM has maximum SNR of 74dB and power consumption is 50mW at 3.3V.

• Journal of Korean Institute of Industrial Engineers
• /
• v.23 no.3
• /
• pp.581-595
• /
• 1997

The procedure of grouping the machines and parts to form cells is called manufacturing cell design. The manufacturing cell design is an important step in the development and implementation of advanced manufacturing systems. For the successful implementation of the manufacturing systems, identification of independent manufacturing cells, i.e., cells where parts are completely processed in the cell and no intercell movements, is necessary in the design phase. In this paper, we developed a mixed integer programming model and genetic algorithm based procedure to solve the independent manufacturing cells design problem considering the alternative process plans and machines duplication. Several manufacturing parameters such as, production volume, machine capacity, processing time, number of cells and cell size, are considered in the process. The model determines the process plan for parts, port families and machine cells simultaneously. The model has been verified with the numerical examples.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.11 no.6
• /
• pp.63-73
• /
• 2008

The helicopter position, heading data and the direction finding data of ESM are essentially required to compensate the parallax and analyze the direction finding accuracy of heliborne ESM in flight test phase. In the case of the long test range compared with small platform like as LYNX helicopter and Jisim Island test site, the parallax compensation for direction finding accuracy calculation and GPS position error can be neglected. In this paper, the direction finding accuracy on the basis of helicopter propeller was calculated by coordinate changing between helicopter and transmitting antenna from WGS84 coordinate to navigation coordinate using helicopter position and direction finding data.

• Proceedings of the KIPE Conference
• /
• 2004.07b
• /
• pp.887-890
• /
• 2004

This paper presents a microprocessor controlled electronic ballast for HID lamps, which gives automatic switching between MH and HPS lamps. Lamp identification is carried out by checking variation of lamp impedance at warm-up phase. Direct spread spectrum is done by applying 1 kHz triangular wave for removing acoustic resonance. This frequency modulation of 1 kHz gives also low EMI level. The microprocessor controls the voltage of DC-bus, the voltage of ignition pulses, the power of output. A 250W electronic ballast is implemented with ATmega16 CPU.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.406-409
• /
• 2001

In this paper, the microstructure and the dielectric properties of the Sr$_{1-x}$ Ca$_{x}$TiO$_3$(0$\leq$$\chi$$\leq$0.2) -based grain boundary layer ceramics were investigated. The specimens were sintered from 142$0^{\circ}C$ to 152$0^{\circ}C$ for 4hr. in $N_2$ gas. The 2nd phase formed by thermal diffusing from the surface lead to a very high apparent dielectric constant, $\varepsilon$$_{r}$>50000. The structural properties of the specimens were studied by X-ray diffraction and SEM, EDX. All specimens exhibited cubic structure. Increasing content of Ca, the peak intensity were decreased.ed.d.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.605-607
• /
• 2001

In this paper, an off-tine UPS with CVT(constant voltage transformer) is designed and the experimental result and problems of the designed UPS is given and discussed. This off-line UPS consists of triple-port CVT and PWM inverter which acts as charger and inverter. It can be evaluated in low price because haying simple structure. It offers high performance because CVT restricts the short current automatically about two or three times of rated current, has nearly unit power factor and constant output voltage to varying input voltage. The weak points of this UPS are that the output voltage waveform is not perfect sinusoidal and has phase difference to input voltage. The experimental result and problems of the designed UPS is given.

• 제어로봇시스템학회:학술대회논문집
• /
• 1994.10a
• /
• pp.324-327
• /
• 1994

In this paper, a new design method of variable structure model following control system(VSMFCS) for robot manipulators is proposed. The proposed controller overcomed reaching phase problem by using function augmenting scheme to the sliding surface. Therefore, it can be guaranteed that the overall system always has a robust property against parameter variations and external disturbances. Furthermore, the proposed controller does not use the model state, .chi.$_{m}$, different from other previous works. Regardless of not using the model state, the model following error dynamics, virtual dynamics, is shown to be globally exponentially stable. The efficiency of the proposed method has been demonstrated by an example.e.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.8
• /
• pp.698-703
• /
• 2009

We report the studies on the structrural properties of Langmuir Blodgett (LB) films fabricated from the copolymer of vinylidenefluoride (VDF) with trifluoroethylene(TrFE). The formation of nanomesas induced by thermal annealing at $135\;^{\circ}C$ for 1 hour was investigated with the atomic force microscope (AFM) and the X-ray diffractometer (XRD). From the result of surface morphology change in 30 monolayer LB film, we find that the annealing treatment on the P(VDF-TrFE) LB film result in the plastic deformation of crystalline polymer. The ${\beta}$ phase crytalline structure in annealed LB film was clearly confirmed from the XRD peak at $19.7^{\circ}$.