• 산업기술연구
• /
• 제18권
• /
• pp.267-275
• /
• 1998

Continuous thermodynamics has been applied for modeling of phase equilibria in multicomponent mixtures, to avoid disadvantages of the pseudo-component and key-component method. In this paper continuous thermodynamic relations formulated by using the Pate-Teja equation of state were adopted for calculations of phase equilibria in natural gas mixtures, crude oil mixtures and mixtures extracted by supercritical $CO_2$ fluids. Calculations of phase equilibria were performed by two procedures ; a moment method coupled with the beta distribution function and a quadrature method combined with Gaussian-Legendre polynomials. Calculated results were compared with experimental data. It was showed that continuous thermodynamic frameworks considered in this paper were well-matched to experimental data.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1370-1373
• /
• 2003

Specimens of Ti-10Ta-10Nb have been tested for Rockwall hardness after heating to either the $\alpha$+$\beta$ and $\beta$-phase field. And the specific heat and the dilatometer of Ti-10Ta-103Nb swaged have been measured. From the result, the $\beta$ transus of the alloy was determined to be 82$0^{\circ}C$. The hot deformation behavior of Ti-10Ta-10Nb with an $\alpha$+$\beta$ microstructure is modeled in the temperature 75$0^{\circ}C$ and strain rate range 0.001-10$^{-1}$

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.1014-1017
• /
• 2003

열증착법을 이용하여 copper(II) phthalocyane (CuPc)의 박막을 제작하였다. 기판의 예열 온도를 달리하여 제작된 CuPc의 박막은 ${\alpha}-phase$와 ${\beta}-phase$로 구분할 수 있으며 phase에 따른 결정 구조를 관찰하기 위해 x-ray diffraction을 사용하고 peak의 위치를 관찰하였다. 또한 SEM, UV visible absorption spectra의 변화를 통해 온도에 따라 상전이가 이행해 가는 모습을 구체적으로 관측하였다. 이러한 결정 구조의 변화는 CuPc 박막의 전기전도 특성에 영향을 달리하여 유기발광 소자에 응용이 가능할 것으로 예상된다.

• 대한치과기공학회지
• /
• 제28권1호
• /
• pp.27-41
• /
• 2006

The physical property and phase transformation in a commercial dental casting high gold alloy was investigated as a function of ageing temperature and time using microvickers hardness tester, X-ray diffraction, optical and electron microscopy and EPMA analyser. 1. With increasing ageing time, the hardness of solution-treated gold alloys increased slowly at the initial stage of ageing treatment at an ageing temperature of $300{\sim}400^{\circ}C$, and it reached a maximum value of hardness at the medium stage. Finally, it decreased gradually during further ageing. The maximum value of hardness at was similar with that of the conventional materials and suitable for using as the crown & bridge. 2. During isothermal ageing at a temperature range of $300{\sim}400^{\circ}C$, three phases consisting of the Au-rich ${\alpha}_1$phase with a face-centered cubic structure, the Pt3Zn ${\alpha}_2$phase with an ordered AuCu3(L12) type(f.c.c.) and the Pt-rich ${\alpha}_3$phase with face-centered cubic structure in solution-treated gold alloys were transformed into different three phases consisting of the ${\alpha}_1$phase, the ${\alpha}_3$phase and the PtZn $\beta$phase with an ordered AuCu I(L10) type. 3. The hardening of gold alloys was attributed to the lattice strains of the matrix resulting from the transformation of the ${\alpha}_2$phase to the $\beta$phase. 4. The softening of gold alloys during over-ageing was attributed to the coarsening of the nodules consisting of the $\beta$phase and ${\alpha}_1$matrix.

• Journal of Mechanical Science and Technology
• /
• 제20권1호
• /
• pp.13-18
• /
• 2006

Ti-8Ta-3Nb, as a new biomaterial, was prepared by cast and swaging process. Their deformation behavior of Ti-8Ta-3Nb alloy has been characterized on the basis of its flow stress variation obtained from the true strain rate compression testing in the temperature of $700-900^{\circ}C$ and strain rate of $0.001-10\;s^{-1}$. At the strain rates lower than $0.1\;s^{-1}$ and the all temperature ranges which consist of two phase ${\alpha}+{\beta}$ as well as single ${\beta}$ phase fields, the flow curves show a small degree of flow softening behavior. In contrast, the shapes of the flow curves at other strain rates indicate unstable behavior. The shapes of the flow curves were similar in both as-cast and swaged specimen as well as in both ${\alpha}+{\beta}$ phase and ${\beta}$ phase. The flow stress data did not obey the kinetic rate equation over the entire regime of testing but a good fit has been obtained in the intermediate range of temperatures ($750-850^{\circ}C$). In this range, a stress exponent value of about 7.7 in as-cast specimens and about 6.2 in swaged specimens with an apparent activation energy of about 300 kJ/mol and about 206 kJ/mol respectively have been evaluated.

• 한국재료학회지
• /
• 제26권5호
• /
• pp.287-291
• /
• 2016

The effect of heat treatment on the microstructure and mechanical properties of cast Ti-6%Al-4%V alloy was investigated. Heat treatment of cast Ti-6Al-4V alloy was conducted by solution treatment at $950^{\circ}C$ for 30 min; this was followed by water quenching and then aging at $550^{\circ}C$ for 1 to 1440 min. The highest hardness of the heat-treated specimens was obtained by solution treatment and subsequent aging for 5 min due to precipitates of fine ${\alpha}$ that formed from retained ${\beta}$ phase. The tensile strength of this alloy increased without dramatic decrease of the ductility due to microstructural refinement resulting from the decomposition of ${\alpha}^{\prime}$ martensite into fine ${\alpha}$ and ${\beta}$ phases, and also due to the fine ${\alpha}$ phase formed from the retained ${\beta}$ phase by aging treatment for 5 min. In addition, this strengthening might be caused by the transformation induced plasticity (TRIP) effect, which is a strain-induced martensite transformation from the retained ${\beta}$ phase during deformation, and which occurs even after aging treatment at $550^{\circ}C$ for 5 min.

• 한국표면공학회지
• /
• 제36권2호
• /
• pp.200-205
• /
• 2003

Thermoelectric p-type $Fe_{0.98}$ $Mn_{ 0.02}$$Si_2$ bulk specimens have been produced by mechanical alloying and consolidation by vacuum hot pressing. The subsequent isothermal annealing was not able to fully transform the mestastable as -milled powders into the $\beta$ $-FeSi_2$ phase, so that the obtained matrix consisted of not only thermoelectric semiconducting $\beta$-FeSi$_2$ but also some residual, untransformed metallic $\alpha$ $- Fe_2$$Si_{ 5}$ and $\varepsilon$-FeSi mixtures. Interestingly, $\beta$ - $FeSi_2$ was more easily obtained in the low density specimen when compared to the high density specimen. The oxidation at 700 and $800^{\circ}C$ in air led to the phase transformation of the above described iron - silicides and the formation of a thin silica surface layer.

• 한국추진공학회지
• /
• 제4권4호
• /
• pp.9-17
• /
• 2000

준안정상인 $\beta$형 HNIW의 용해와 안정상인 $\varepsilon$형 HNIW의 성장 특성을 고려한 모델식을 물질수지와 한께 계산하는 방법으로 결정성장 속도와 용해 속도를 계산하였다. 제시된 모델은 용액을 매체로 하여 진행되는 $\beta$$\longrightarrow$$\varepsilon$전이 현상에 대한 속도론적 데이터를 모사 하는데 유용하였다. 2 단 모델을 이용한 유효 인수로부터, 격정성장 과정에서 표면 축적 단계의 영향은 작으며, 확산 의존성은 ethyl acetate와 chloroform의 혼합 용매 중 chloroform의 함량이 증가함에 따라 감소함을 보였다. 이들 속도론 적 계수들을 이용한 수치모사를 통하여 $\varepsilon$-HNIW의 입자 크기를 예측하는 것이 가능하였다.

• Bulletin of the Korean Chemical Society
• /
• 제34권12호
• /
• pp.3829-3834
• /
• 2013

$H{\beta}$ (core)/SAPO-11 (shell) composite molecular sieve was synthesized by the hydrothermal method in order to combine the advantages of $H{\beta}$ and SAPO-11 for the methylation of naphthalene with methanol. For comparison, the mechanical mixture was prepared through the blending of $H{\beta}$ and SAPO-11. The physicochemical properties of $H{\beta}$, SAPO-11, the composite and the mechanical mixture were characterized by various characterization methods. The characterization results indicated that $H{\beta}$/SAPO-11 composite molecular sieve exhibited a core-shell structure, with the $H{\beta}$ phase as the core and the SAPO-11 phase as the shell. The pore diameter of the composite was between that of $H{\beta}$ and SAPO-11. The composite had fewer acid sites than $H{\beta}$ and mechanical mixture while more acid sites than SAPO-11. The experimental results indicated that the composite exhibited high catalytic performances for the methylation of naphthalene with methanol.

• 열처리공학회지
• /
• 제16권2호
• /
• pp.90-96
• /
• 2003

The effect of betatizing temperature on microstructure and transformation characteristics in a Cu-AI-Ni based pseudoelastic alloy fabricated by heated mold continuous casting by using metallography, XRD and calorimetry. The microstructure of cast rod betatized at $600^{\circ}C$ revealed a ${\beta}_1$ parent phase and a ${\gamma}_2$ phase precipitated along the casting direction. When the cast rod was betatized at the elevated temperature above $600^{\circ}C$, the ${\gamma}_2$ phase is completely dissolved into the matrix so that the volume fraction of the ${\gamma}_2$ phase was decreased. The parent phase was stabilized by betatizing at $600^{\circ}C$. However, the ${\beta}_1$ parent phase was transformed to both ${{\beta}_1}^{\prime}$ and ${{\gamma}_1}^{\prime}$ martensites with increasing betatizing temperatures above $600^{\circ}C$, while $M_s$ and $A_s$ temperatures were decreased. The stress-strain curves for compression test were not same with betatizing temperature; the stress-strain curves of the specimen betatized at $600^{\circ}C$ and $700^{\circ}C$ were linear but those of the specimen betatized at $800^{\circ}C$ and $900^{\circ}C$ were not linear.