• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.104-110
• /
• 2006

The advantage of the DSM which employ multi-bit quantizer is the increased SNR at the modulator's output. Typically 6 dB improvement is effected for every one additional bit. But multi-bit quantizer evidently requires multi-bit DAC in the feedback loop. The integral linearity error of the feedback DAC has direct impact upon the system performance and degraded SNR of the system. In order to mitigate the negative impact the DAC has on the system performance, many DEM(Dynamic Element Matching) schemes has been proposed. Among the proposed schemes, four schemes(DER,CLA,ILA,DWA) are explained and its performance has been compared. DWA(Data Weighted Averaging) method shows the best performance of the all.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1887-1894
• /
• 2010

This paper proposes a new switched-capacitor sigma-delta modulator for automotive radars. Developed modulator is used to perform high-resolution analog-to-digital conversion (ADC) of high frequency band signal in a radar system. It has supply voltage of 2.7V, and has body-effect compensated switch configuration with low voltage and low distortion. The modulator has been implemented in a $0.25{\mu}m$ double-poly and triple-metal standard CMOS process, and it has die area of $1.9{\times}1.5mm^{2}$. It showed better total harmonic distortion of 20dB than the conventional bootstrapped circuit at the supply voltage of 2.7V.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.982-985
• /
• 1999

An efficient technique to trade off speed for resolution is the sigma-delta modulation (SDM). This paper proposes a new SDM architecture to improve conversion rates and SNR(Signal-to Noise Ratio) by using master clock and four divided clock. The charateristics of the proposed SDM are simulated in MATLAB environment. and optimizing the capacitor sizes is done by iterative processing. other analog characteristics are simulated using 0.65${\mu}{\textrm}{m}$ n-well CMOS process, double poly and single metal. The result of simulation shows that more increasing the effective bits of internal ADC/DAC, bigger the improvement of SNR.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.1
• /
• pp.52-58
• /
• 2009

A low voltage, low power delta-sigma modulator is proposed for cardiac pacemaker applications. A cascade of delta-sigma modulator stages that employ a feedforward topology has been used to implement a high-resolution oversampling ADC under the low supply. An inverter-based switched-capacitor circuit technique is used for low-voltage operation and ultra-low power consumption. An experimental prototype of the proposed circuit has been implemented in a $0.35-{\mu}m$ CMOS process, and it achieves 61-dB SNDR, 63-dB SNR, and 65-dB DR for a 120-Hz signal bandwidth at 7.6-kHz sampling frequency. The power consumption is only 280 nW at 1-V power supply.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.3
• /
• pp.69-80
• /
• 2015

This paper is writing about developing magnet power supply. It is very important for power supply to obtain output current in high precision and high stability. As a switching noise and a power noise are the cause of disrupting the stability of output current, to remove these at the front end, low pass filter with 300Hz cutoff frequency is designed and placed. And also to minimize switching noise of the current into magnet and to stop abrupt fluctuations, output filter should be designed, when doing this, we design it by considering load has high value inductance. As power supply demands the stability of less than 5ppm, high precision 24bit(300nV/bit) analog digital converter is needed. As resolving power of 24bit(300nV/bit) analog digital converter is high, it is also very important to design the input stage of analog digital converter. To remove input noise, 4th order low pass filter is composed. Due to the limitation of clock, to minimize quantization error between 15bit DPWM and output of ADC having 24bit resolving power, ${\Sigma}-{\Delta}$ modulation is used and bit contracted DPWM is constituted. And before implementing, to maximize efficiency, simulink is used.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.44 no.2
• /
• pp.34-45
• /
• 2007

Digital decimation filter is inevitable in oversampled sigma-delta A/D converters for the sake of reducing the oversampled rate to Nyquist rate. This paper presented a Verilog-HDL design and implementation of an area-efficient digital decimation filter that provides time-to-market advantage for sigma-delta analog-to-digital converters. The digital decimation filter consists of CIC(cascaded integrator-comb) filter and two cascaded half-band FIR filters. A CSD(canonical signed digit) representation of filter coefficients is used to minimize area and reduce in hardware complexity of multiplication arithmetic. Coefficient multiplications are implemented by using shifters and adders. This three-stage decimation filter is fabricated in $0.25-{\mu}m$ CMOS technology and incorporates $1.36mm^2$ of active area, shows 4.4 mW power consumption at clock rate of 2.8224 MHz. Measured results show that this digital decimation filter is suitable for digital audio decimation filters.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.6
• /
• pp.608-614
• /
• 2015

A multi-channel audio CODEC with inter-channel interference suppression is proposed, in which channel switching noise-referred sampling error is significantly reduced. It also supports a coarse/fine mode operation for fast frequency tracking with good harmonic performance. The proposed multi-channel audio CODEC was designed in a 65 nm CMOS process. Measured results indicated that SNR and SNDR of ADC were 93 dB and 84dB, respectively, with SNDR improved by 43 dB. Those of DAC were 96 dB and 87 dB, respectively, with SNDR improved by 45 dB when all the channels are running independently.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.1
• /
• pp.82-89
• /
• 2014

Recently, inertial sensors are popularly used for the location and position recognition of small devices for M2M/IoT. In this paper, we designed low power, low noise, small sized 6-axis inertial sensor IC for mobile applications, which uses a 3-axis piezo-electric gyroscope sensor and a 3-axis piezo-resistive accelerometer sensor. Proposed IC is composed of 3-axis gyroscope readout circuit, two gyroscope sensor driving circuits, 3-axis accelerometer readout circuit, 16bit sigma-delta ADC, digital filter and control circuit and memory. TSMC $0.18{\mu}m$ mixed signal CMOS process was used. Proposed IC reduces 27% of the current consumption of LSM330.

• Proceedings of the KIEE Conference
• /
• 2006.10c
• /
• pp.388-390
• /
• 2006

This paper presents a hybrid SoC design for phase detection of single tone signal. The designed hybrid SoC is composed of three functional blocks, i.e., an analog to digital converter module, a phase detection module and a controller module. A design of the controller module is based on a 16-bit RISC architecture. An I/O interface and an LCD control interface for transmission and display of phase measurement values are included in the design of the controller module. A design of the phase detector is based on a recursive sliding-DFT. The recursive architecture effectively reduces the gate numbers required in the implementation of the module. The ADC module includes a single-bit second-order sigma-delta modulator and a digital decimation filter. The decimation filter is designed to give 98dB of SNR for the ADC. The effective resolution of the ADC is enhanced to 98dB of SNR by the incorporation of a pre FIR filter, a 2-stage cascaded integrator- comb(CIC) filter and a 30-tab FIR filter in the decimation. The hybrid SoC is verified in FPGA and implemented in 0.35 CMOS Technology.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.4
• /
• pp.630-638
• /
• 2001

This paper has been proposed a structure composed of FIRs and IIR filters as digital decimation filter to compensate the drooping inband on the high precision AU chips. The area of chip has been reduced compared with the conventional structure because the RAM and MAC is reduced. The passband ripple$(\leq\; 0.4535 \times fs)$, passband attenuation(at $\; 0.4535 \times fs$ and stopband attenuation$(\geq\; 0.59\times fs)$ of the 6th-order $\Delta\Sigma$ modulator and digital decimation filter had $\pm0.0007[dB]$, -0.0013[dB] and -110[dB] respectively. Also the inband group delay, which was almost same compared with the conventional digital decimation filter structure, was 30.07/fs[s] band the error of group delay was 0.1672%.