• Korean Journal of Ecology and Environment
• /
• v.37 no.3 s.108
• /
• pp.304-312
• /
• 2004

The transient dynamics of three-trophic populations (prey, predator, and super predator) using ratio-dependent models responding to environmental impacts is analyzed. Environmental factors were divided into two parts: periodic factor (e.g., temperature) and general noise. Periodic factor was addressed as a frequency and bias, while general noise was expressed as a Gaussian distribution. Temperature bias ${\varepsilon}$, temperature frequency ${\Omega}$, and Gaussian noise amplitude ${\`{O}}$ accordingly revealed diverse status of population dynamics in three-trophic food chain, including extinction of species. The model showed stable limit cycles and strange attractors in the long-time behavior depending upon various values of the parameters. The dynamic behavior of the system appeared to be sensitive to changes in environmental input. The parameters of environmental input play an important role in determining extinction time of super predator and predator populations.

• Korean Journal of Metals and Materials
• /
• v.47 no.9
• /
• pp.591-596
• /
• 2009

$TiN_xO_y/TiN_x$ multi-layer thin films with a high resistance(${\sim}k{\Omega}$) were deposited on $SiO_2/Si$ substrates at room temperature by sputtering. The $TiN_x$ thin films show island and smooth surface morphology in samples prepared by ${\alpha}$ and RF magnetron sputtering, respectively. $TiN_xO_y/TiN_x$ multi-layer in has been developed to control temperature coefficient of resistance(TCR) by the incorporation of $TiN_x$ layer(positive TCR) inserted into $TiN_xO_y$ layers(negative TCR). Electrical and structural properties of sputtered $TiN_xO_y/TiN_x$ multi-layer films were investigated as a function of annealing temperature. In order to achieve a stable high resistivity, multi-layer films were annealed at various temperatures in oxygen ambient. Samples annealed at $700^{\circ}C$ for 1 min exhibited good TCR value of approximately $-54 ppm/^{\circ}C$ and a stable high resistivity around $20k{\Omega}/sq$. with good reversibility.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.1
• /
• pp.10-14
• /
• 2008

Differently from BSCCO tapes which are fabricated by powder-in-tube method, the coated conductors are made by the evaporation of YBCO on metal substrate. Due to this structural merit, although the coated conductors are generally used for large current transportation, they are expected to be favorable to the purpose of the fault current limitation as well. In this study, using YBCO coated conductor having copper stabilizer formed by plating technique(produced by Superpower Co.), we investigated the over-current characteristics of the coated conductor. The coated conductors had 85 A $I_c$ and 90 K $T_c$. The resistance of the conductor was 0.93 $m{\Omega}/cm$ at 300 K and 0.17 $m{\Omega}/cm$ at the temperature right above $T_c$. To the coated conductors, we applied the voltages of the range from 150 $V_{rms}$ to 230 $V_{rms}$ and measured the V-I curves using four probe method. From the results, we could analyze the electric behavior of the coated conductor in flux flow state. As the current exceed $I_c$, the currents were distributed into the superconductor and metal stabilizer. The amounts of the currents shared through both current paths were calculated under the assumption that the ,Joule heating was perfectly eliminated by $LN_2$ surrounding the conductor. Finally, the condition for the stable current flowing state which does not affect the conductor was established from the analysis on the over-current characteristics.

• Journal of Environmental Science International
• /
• v.5 no.4
• /
• pp.535-544
• /
• 1996

In the development of Molten Carbonate Fuel Cell, one of the serious problems is the dissolution of cathode material. Therefore, the development of the alternative cathode which is stable in molten carbonate is needed. In this research, the licoo, was chosen as alternative cathode material. $LiCoO_2$ powder was synthesized by high temperature calcination method and by citrate sol-gel method. And its structure and physical iharacteristics were analyzed by XRD, 1 R, TCA and porosimeter. The conductivity and solubility of $LiCoO_2$ electrode were also measured. Homogeneous $LiCoO_2$ Powder was obtained by citrate sol-Rel method at 445$^{\circ}C$, however, obtained above 75$0^{\circ}C$ by high temperature calcination method. Homogeneous particle size distribution and fine powder were obtained by the citrate sol-Rel method. $LiCoO_2$ electrode showed higher electric conductivity ($1.7 $\Omega$^{-1}cm^{-1}$) than NiO (0.1 $\Omega$^{-9} cm^{-1}) at $650^{\circ}C$. The solubilities of $LiCoO_2$ electrode in electrolyte were varies 0.6 to 1.0 ppm during 200 hours. So, the solubilities of $LiCoO_2$ were much lower than that of NiO.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.247-248
• /
• 2006

Carbon nitride films were evaluated that they had many advantages for miniature micro-humidity-sensors using the standard CMOS technology humidity sensing properties and CV characteristics of the carbon nitride films have been investigated for fabricating one chip HUSFET(Humidity Sensitive Field Effect Transistor) humidity sensors Carbon nitride films were deposited on silicon substrate with meshed electrodes by reactive RF magnetron sputtering system. The capacitor-type humidity sensor revealed good humidity-impedance characteristics with a wide range of relative humidity changes, decreasing $254k{\Omega}$ to $16k{\Omega}$ according to increase of relative humidity between 5% ~ 95% and the films were very stable on the Si wafer. These results reveal that $CN_x$ thin films can be used for Si based or HUSFET structure one chip micro-humidity sensors.

• Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
• /
• 2000.10a
• /
• pp.147-153
• /
• 2000

The fatigue crack propagation behavior of the SA516/70 steel which is used for pressure vessels was examined experimentally at room temperature, $150^{\circ}C$, $250^{\circ}C$ and $370^{\circ}C$ with stress ratio of R=0.1 and 0.3. The fatigue crack propagation rate da/dN related with the stress intensity factor range $\Omega\textrm{K}$ was influenced by the stress ratio within the stable growth of fatigue crack(Region II) with an increase in $\Omega\textrm{K}$. The resistance to the fatigue crack growth at high temperature is higher in comparison with that at room temperature, and the resistance attributed to the extent of plasticity-induced by compressive residual stress according to the cyclic loads. Fractographic examinations reveal that the differences of the fatigue crack growth characteristics between room and high temperatures are mainly explained by the crack closure and oxide-induced by high temperature.

• Proceedings of the Membrane Society of Korea Conference
• /
• 1999.07a
• /
• pp.115-115
• /
• 1999

In this work a new process was developed for the sulfonation of the chemicallly stable engineering polymer polyethersulfone as membrane materials for electrodialysis or a flow battery applications. Commercially available polyethersulfone polymer was partially sulfonated using a CSA sulfonating agent in a dichloromethane solvent, which sulfonated polyethersulfone with various sulfonation levels have been prepared. Sulfonated polyethersulfone (SPES) membranes with different ion capacities were prepared for the purpose of identifying cation exchange membrane properties, in an attempt to find a low cost replacement for Nafion, which most of the perfluorinated membranes, known to exhibit a prolonged service life, are expensive and difficult to process. The following features were determined: the degree of sulfonation, water uptake, thermal analysis, and electrochemical properties such as ion exchange capacities, resistivity, selectivity of ion permeation. The surface of the cation exchange membranes, decomposed with the H202-treatment, were observed by using scanning electron microscope. The area resistivities of SPES mebranes in 5N-NaOH decreased from $2,150{\;}{\Omega}-cm2$ to less than $15{\Omega}-cm2$ as the ion exchange capacity (IEC) increased from 0.62 to 1.73 millieequivlants per dry gram(meq/dg).eq/dg).

• Resources Recycling
• /
• v.14 no.1
• /
• pp.39-46
• /
• 2005

A solid-state high power torch with inter-electrode insert (IEI) was developed to treat solid waste (for example, incinerated ash), and it's operation characteristics were obtained in the plasma facility test for waste treatment. According to torch test from this study, at the non-transferred mode voltage is increased by gas volume proportionally, and at the transferred mode it is not affected to voltage change. Especially arc voltage is sustained stable at the range of 10% of total Fe in slag. In addition, Electrical conductivity is 0.05~0.25${\Omega}^{-1}cm^{-1}$, torch efficiency is 75~85% and Erosion rate is 2${\times}10^{-6}~6{\times}10^{-6}$ kg/s.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.20 no.11
• /
• pp.948-952
• /
• 2007

In this study, a low temperature sintering multilayer piezoelectric transformer for a DC-DC converter was manufactured using $(Pb,Ca,Sr,)(Ti,Mn,Sb)O_3$ ceramics. Its electrical properties were investigated according to the variation in frequency and load resistance. The voltage step-up ratio of the multilayer piezoelectric transformer showed a maximum value at a resonant frequency of input part and increased with an increase of load resistance. The efficiency of the multilayer piezoelectric transformer showed the highest value at a load resistance of 17 $\Omega$. The output power was increased with increasing input voltage. Temperature increase of the multilayer piezoelectric transformer was increased with the increase of output power. At the load resistance of 17 $\Omega$, the multilayer piezoelectric transformer showed the temperature rises of about $20^{\circ}C$ at the output power of 18 W, and stable driving characteristics.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.13 no.6
• /
• pp.1177-1182
• /
• 2018

We designed a 500W zero voltage switching DC / DC converter operating at 100Mhz with phase shift topology using UCC3895 driver. The dead time of the UCC3895 driver is designed so that the leading and lagging leg of the full bridge can be driven separately. So, the dead time can be given between the two legs separately. The dead time, which is an asymmetrical relationship between the two legs, enables the implementation of zero voltage switching. This paper proposed a negative feedback circuit design method for stable output voltage. The maximum efficiency of the prototype was 95.5% at $500{\Omega}$ load.