• Journal of the Korean Electrochemical Society
• /
• v.3 no.2
• /
• pp.115-120
• /
• 2000

All solid-state thin film micro-batteries consisting of lithium metal anode, an amorphous LiPON electrolyte and cathode of vanadium oxide have been fabricated and characterized, which were fabricated with cell structure of $Li/LiPON/V_2O_5Pt$. The effect of various oxygen partial pressure on the electrochemical properties of vanadium oxide thin films formed by d.c. reactive sputtering deposition were investigated. The vanadium oxide thin film with deposition condition of $20\%\;O_2/Ar$ ratio showed good cycling behavior. In in-siか process, the LiPON electrolyte was deposited on the $V_2O_5$ films without breaking vacuum by r.f. magnetron sputtering at room temperature. After deposition of the amorphous LiPON, the Li metal films were grown by a thermal evaporator in a dry room. The charge-discharge cycle measurements as a function of current density and voltage variation revealed that the $Li/LiPON/V_2O_5$ thin film had excellent rechargeable properly when current density was $7{\mu}A/cm^2$. and cut-off voltage was between 3.6 and 2.7V In practical experiment, a stopwatch ran on this $Li/LiPON/V_2O_5$ thin film micro-battery. This result means that thin film micro-battery fabricated by in-siか process is a promising for power source for electronic devices.

• Korean Chemical Engineering Research
• /
• v.57 no.6
• /
• pp.832-840
• /
• 2019

To improve the electrochemical performances of the cathode materials, boron-doped $LiNi_{0.90}Co_{0.05}Ti_{0.05}O_2$ were synthesized by using concentration gradient precursor. The characteristics of the prepared cathode materials were analyzed by XRD, SEM, EDS, PSA, ICP-OES and electrical conductivity measurement. The electrochemical performances were investigated by initial charge/discharge capacity, cycle stability, C-rate, cyclic voltammetry and electrochemical impedance spectroscopy. The cathode material with 0.5 mol% boron exhibited a capacity of 187 mAh/g (0.5 C) in a voltage range of 2.7~4.3 V(vs. $Li/Li^+$), and an capacity retention of 94.7% after 50 cycles. In the relatively high voltage range of 2.7~4.5 V(vs. $Li/Li^+$), it showed a high capacity of 200 mAh/g and capacity retention of 80.5% after 50 cycles.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.9
• /
• pp.696-700
• /
• 2010

We fabricated red and blue organic light emitting display (OLEDs) which had the two kinds of multi-structure of ITO/HIL/HTL/EML/ETL/LiF/Al and ITO/HIL/HTL/EML/ETL/LiF/Al/LiF. In the case of red OLED that had LiF/Al/LiF structure compared to LiF/Al structure, the current density increased from 4.3 mA/$cm^2$ to 7.3 mA/$cm^2$, and the brightness increased from 488 cd/$m^2$ to 1,023 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 11.28 cd/A to 13.95 cd/A. Also in the case of blue OLED that had LiF on Al cathode layer, the current density increased from 1.2 mA/$cm^2$ to 1.8 mA/$cm^2$, and the brightness increased from 45 cd/$m^2$ to 85 cd/$m^2$ at 7.0 V, and as a result the current efficiency was improved from 3.69 cd/A to 4.82 cd/A. Through these experimental results it could be suggested that the LiF layer formed on Al prevents the oxidation of Al surface, and the electrode resistance become low with increase of supplied electrons, therefore the brightness and the efficiency are improved from the influence to the well-balanced bonding of electron and hole at emitting layer.

• Korean Journal of Optics and Photonics
• /
• v.4 no.2
• /
• pp.200-205
• /
• 1993

We generated the second harmonic of Ti:sapphire laser in LiI$O_3$ and BBO crystals. Two LiI$O_3$, crystals and a BBO crystal were used, and the lengths of LiI$O_3$ crystals were 5, 10 mm and that of BBO was 7 mm. We measured the conversion efficiencies of LiI$O_3$ and BBO in the wavelength range of 780-810 nm, and compared with the caculation of theory. The measured second harmonic conversion coefficients were (1.06${\pm}0.05){\times}10^4\;W^1$(10mm), (5.28${\pm}0.33){\times}10^5\;W^1$(5mm), and (2.96${\pm}0.05){\times}10^5\;W^1$(BBO, 7 mm) at the fundamental wavelength of 794 nm.

• Resources Recycling
• /
• v.7 no.5
• /
• pp.52-57
• /
• 1998

Effect of Si in the electrochemical corrosion characteristics of Mg-Li-Al light alloy has been investigated by means of potentiodynamic polarization study. The elecrochemical behaviors were evaluated in 003% NaCl solution and the solution buffered with KH$_{2}PO_{5}{\cdot}$NaOH at room temperature. It was found that the addition of very small quantity of Si (0.48 wt%) in Mg-Li-Al light alloy increased corrosion rates and amount of corrosion products and decreated the pitting resistance of the alloy. From the results it was concluded that Si which is added to increase the strength of Mg-Li-Al alloy is harmful to corrosion properties of the alloy.

• Korean Journal of Metals and Materials
• /
• v.50 no.12
• /
• pp.955-959
• /
• 2012

To increase the hydrogen storage capacity of Mg-based materials, a sample with a composition of 69.7 wt% $MgH_2$ + 30.3 wt% $LiBH_4$ was prepared by planetary ball milling under hydrogen. The absorption and desorption properties of unmilled $MgH_2$, unmilled $LiBH_4$, and 69.7 wt% $MgH_2$ + 30.3 wt% $LiBH_4$ were examined. At 648 K the unmilled $MgH_2$ desorbed 5.70 wt% for 60 min. The unmilled $LiBH_4$ desorbed 6.40 wt% H for 780 min at 673 K. The 69.7 wt% $MgH_2$ + 30.3 wt% $LiBH_4$ sample desorbed 3.10 wt% H for 50 min, and 3.32 wt% H for 300 min at 623 K at the second cycle.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.2
• /
• pp.58-67
• /
• 2015

The effects of electrolyte additives, lithium bis(oxalate)borate (LiBOB), fluoroethylene carbonate (FEC), vinylene carbonate (VC), 2-(triphenylphosphoranylidene) succinic anhydride (TPSA), on high-temperature storage properties of $Li(Ni_{1/3}Co_{1/3}Mn_{1/3})O_2$/graphite are investigated with coin-type full cells. The 1 wt.% LiBOB-containing electrolyte showed the highest capacity retention after high temperature ($60^{\circ}C$) storage for 20 days, 86.7%, which is about 5% higher than the reference electrolyte, 1.15M lithium hexafluorophosphate ($LiPF_6$) in ethylene carbonate/ethyl methyl carbonate (EC/EMC, 3/7 by volume). This enhancement is closely related to the formation of semi-carbonate compounds originated from $BOB^-$ anions, thereby resulting in lower SEI thickness and interfacial resistance after storage. In addition, the 1 wt.% LiBOB-containing electrolyte also exhibited better cycle performance at 25 and $60^{\circ}C$ than the reference electrolyte, which indicates that LiBOB is an effective additive for high-temperature performance of $Li(Ni_{1/3}Co_{1/3}Mn_{1/3})O_2$/graphite chemistry.

• 한국전기화학회:학술대회논문집
• /
• 1998.10a
• /
• pp.90-90
• /
• 1998

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.11a
• /
• pp.137.1-137.1
• /
• 2011

올리빈 구조의 $LiFePO_4$ 정극 활물질은 $650^{\circ}C$에서 고상법으로 제조되었다. $LiFePO_4$의 전자전도도를 향상시키기 위하여 graphite nanofiber(GNF)를 각각 3wt%, 5wt%, 7wt%, 9wt% 첨가하여 $LiFePO_4$-C를 제조하였다. 제조된 분말의 입자 형태를 확인하기 위하여 X-ray diffraction(XRD)과 File Electronic Scaning Electromicroscopy(FE-SEM)를 측정하였다. XRD결과로부터 제조된 분말은 모두 순수한 결정 구조를 나타내었고 입자의 크기는 약 200nm였다. 5wt% GNF를 첨가한 $LiFePO_4$-C는 기타 첨가량에 비해 방전용량이 가장 높았다. 첫 사이클의 용량은 151.73mAh/g 나타났고 50 사이클 뒤에도 92% 이상을 유지하고 있었다. 첨가하지 않은 것에 비해 43% 증가하였다. $LiFePO_4$-C(3wt%), $LiFePO_4$-C(7wt%), $LiFePO_4$-C(9wt%)의 첫 사이클 방전용량은 각각 147.94mAh/g, 136.64mAh/g, 121.07mAh/g 나타났다. $LiFePO_4$-C(5wt%)에 비해 용량은 떨어쪘지만 순수한 $LiFePO_4$보다 많이 높았다. 임피던스 결과를 보면 기타 첨가량에 비해 $LiFePO_4$-C(5wt%)의 저항 제일 낮았다. 이는 충방전 결과와 일치하였다. graphite nanofiber의 첨가로 인하여 $LiFePO_4$ 정극 활물질의 전자전도도가 높아지고, 따라서 전기화학적 특성도 크게 향상되었다.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.19 no.1
• /
• pp.154-166
• /
• 2016

This study aims to contribute to better understanding the effects of the changes in the parameter values of GroundFilter algorithm(GF), which performs filtering process, and of GridsurfaceCreate algorithm(GC), which creates regular grid, provided in Fusion software on the accuracy of elevation of the final LiDAR-DEM products through comparative analysis. In order to test whether there are significant effects on the accuracy of the final LiDAR-DEM products due to the changes of GF(1, 3, 5, 7, 9) parameter levels and GC(1, 3, 5, 7, 9) parameter levels, two-way ANOVA is conducted based on residuals. The residuals are calculated using the differences between each sample plot's paired field-measured and DEM-derived elevation values given each individual GF and GC level. After that, Tukey HSD test is conducted as a post hoc test for grouping the levels. As a result of two-way ANOVA test, it is found that the change in the GF levels significantly affects the accuracy of LiDAR-DEM elevations(F-value : 27.340, p < 0.01), while the change in the GC levels does not significantly affect the accuracy of LiDAR-DEM elevations(F-value : 0.457). It is also found that the interaction effect between GF and GC levels is not likely to exist(F-value : 0.247). From the results of the Tukey HSD test in the GF levels, GF levels can be divided into two groups('7', '5', '9', '3' vs '1') by the differences of means of residuals. Given the current conditions, LiDAR-DEM can achieve the best accuracy when the level '7' and '3' are given as GF and GC level, respectively.