• Journal of the Korean institute of surface engineering
• /
• v.39 no.6
• /
• pp.255-262
• /
• 2006

Pd-Cu alloy membrane for hydrogen separation was fabricated by sputtering and Cu reflow process. At first, the Pd and Cu was continuously deposited by sputtering method on oxidized Si support, the Cu reflow process was followed. Microstructure of the surface and permeability of the membrane was investigated depending on various reflow temperature, time, Pd/cu composition and supports. With respect to our result, Pd-Cu thin film (90 wt.% Pd/10 wt.% Cu) deposited by sputtering process with thickness of $2{\mu}m$ was heat-treated for Cu reflow The voids of the membrane surface were completely filled and the dense crystal surface was formed by Cu reflow behavior at $700^{\circ}C$ for 1 hour. Cu reflow process, which is adopted for our work, could be applied to fabrication of dense Pd-alloy membrane for hydrogen separation regardless of supports. Ceramic or metal support could be easily used for the membrane fabricated by reflow process. The Cu reflow process must result in void-free surface and dense crystalline of Pd-alloy membrane, which is responsible for improved selectivity oi the membrane.

• Journal of the Korean institute of surface engineering
• /
• v.34 no.6
• /
• pp.545-552
• /
• 2001

Effect of ultrasonic agitation on Pd catalyst treatment was studied in metallization of ceramic boards by Cu electroless plating method.96% $Al_{2}$$O_{3}$ ceramic boards were used as substrate. In this study, the ultrasonic frequency of 28kHz was applied. In Pd catalyst, high density Pd nuclei of small size were formed during ultrasonic agitation. Density of Pd was more improved when using of ultrasonic then no stirring. In electroless plating, plating rate was in the range of 0.6~1.8$\mu\textrm{m}$/hr, which value increased with Rochelle Salts addition. Adhesion strength between ceramic boards and Cu layer was improved of 20% when using ultrasonic agitation at $30^{\circ}C$ ,5min.

• Journal of the Korean institute of surface engineering
• /
• v.50 no.5
• /
• pp.411-420
• /
• 2017

In this paper, two methods of making the Pd-added $SnO_2$ ($Pd-SnO_2$) powder with pure tetragonal phase by the hydrazine method were suggested and compared in terms of crystal structure, surface morphology, and alcohol gas response. One of the addition methods is to use $PdCl_2$ as a Pd source, the other is to use Pd-based organic with oleylamine (OAM). When Pd concentration was increased from 0 to 5 wt%, the average grain size of $Pd-SnO_2$ made with Pd-OAM were decreased from 32 to 12 nm. In the case of using with $PdCl_2$, grain size of the $PdCl_2$ fell to less than 10 nm. However, agglomerated and extruded surface morphology was observed for the films with Pd addition over 4 wt%. The crack-free $Pd-SnO_2$ thick films were able to successfully fill the $30{\mu}m$ gap of patterned Pt electrodes by optimized ink dropping method. Also, the 2 wt% $Pd-SnO_2$ thick film made with PdCl2 showed gas responses ($R_{air}/R_{gas}$) of 3.7, 5.7 and 9.0 at alcohol concentrations of 10, 50 and 100 ppm, respectively. On the other hand, the prepared 3 wt% $Pd-SnO_2$ thick film with Pd-OAM exhibited very excellent responses of 3.4, 6.8 and 12.2 at the equivalent measurement conditions, respectively. The 3 wt% $Pd-SnO_2$ thick film with Pd-OAM has a specific surface area of $31.39m^2/g$.

• Journal of the Korean Magnetics Society
• /
• v.19 no.5
• /
• pp.165-170
• /
• 2009

It is well-known that a meta-stable fcc bulk Fe has an antiferromagnetic (AFM) ground state and could be synthesized by growing Fe on a proper fcc metal substrate. In this study magnetism of Fe monolayers on nonmagnetic fcc transition metal (Cu, Rh, Pd, and Ag) (001) surfaces has been investigated using the all-electron full-potential linearized augmented plane wave method. The Fe monolayers on Rh(001) and Pd(001) surfaces were calculated to be stabilized in an AFM state, whereas the Fe monlayers on Cu(001) and Ag(001) surfaces are stabilized in a ferromagnetic (FM) state. Noting that Cu and Ag have the smallest and largest lattice constants and the fcc bulk Fe with a larger lattice constant is getting stabilized in a ferromagnetic state, it is unexpectable and interesting. The calculated magnetic moments of the Fe atoms on Cu, Rh, Pd, and Ag(001) surfaces are 2.811, 2.945, 2.987, and 2.990 $_{{\mu}B}$ in FM states and 2.624, 2.879, 2.922, and 3.001 $_{{\mu}B}$ in AFM states.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.35 no.2
• /
• pp.47-54
• /
• 1986

Hardware implementation of a 32-channel MFC digital receiver has not been easy and simple, because it requires real time processing of PCM data. In this paper, we introduce a method of designing an MFC digital receiver compactly by the channel distribution method. We have implemented the MFC digital receiver to process many cnannels by distributing channels of the TDM input data directly to the commercial digital signal processor chips(NEC uPD7720), and by carrying out the modified Goertzel Algorithm. The design of low cost, reliable, high speed, and compact MFC receiver will be shown.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.17 no.2
• /
• pp.39-42
• /
• 2011

The aim of this study was to develop the appropriate packaging method for minimally processed sliced onions. The films of different gas permeabilities (LDPE $30{\mu}m$, PD900 and PD941) were used for packaging 1300g of onion slices cut into octuplicate pieces. Perforated LDPE package was prepared as control for comparison. The package atmosphere and onion quality were measured through storage at $1^{\circ}C$ for 38 days. PD900 package of the lowest gas permeability was the best in keeping the fresh-cut onions by maintaining MA conditions of 1-3% $O_2$ and 4-11% $CO_2$ concentrations. The benefits were reduced discoloration, decay and soakness.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.835-839
• /
• 2002

Stoichiometric $LiNbO_3$(LN) single crystals of 1 mm diameter and 30∼40 mm length with co-doped the $Er_2O_3$ and MgO were grown by the Micro-Pulling Down(${\mu}$-PD) method. The grown crystals were investigated for the change of the up-conversion property by the $Er_2O_3$ and MgO addition and the optical damage by the MgO concentration. Also, the crystals were studied the defects using the optical microscope and it is identified the homogeneities of the distribution of the $Er_2O_3$ and MgO concentration by the Electron Probe Micro Analysis(EPMA).

• Journal of the Korean Ceramic Society
• /
• v.46 no.4
• /
• pp.419-424
• /
• 2009

Congruent or stoichiometric $LiNbO_3$ fiber single crystals were grown by the $\mu$-PD method, and the grown fiber crystals have the several (2 or 3) ridges with a diameter of $1.35{\sim}1.5\;mm$ and a length of $40{\sim}100\;mm$. In this $\mu$-PD process, different growth rates ($10{\sim}60\;mm/h$) were applied. Pt wire or $LiNbO_3$ crystal was used as a seed. The properties of grown $LiNbO_3$ fiber single crystals having a-axis or c-axis according to seeds were effected by the grown conditions(Pt tube diameter, pulling speed, after heater etc.). Disk-type $LiNbO_3$ samples were poled in condition of DC 5 V/cm at 1050, 1075 or $1100^{\circ}C$. XRD, SEM, conoscope image through the polarized microscope, $T_C$ measuring apparatus, optical transmittance measuring instrument are used to identify the properties of $LiNbO_3$.

• Korean Journal of Materials Research
• /
• v.19 no.8
• /
• pp.437-442
• /
• 2009

This paper describes an improved strategy for controlling the adhesion force using both the antiadhesion and adhesion layers for a successful large-area transfer process. An MPTMS (3-mercaptopropyltrimethoxysilane) monolayer as an adhesion layer for Au/Pd thin films was deposited on Si substrates by vapor self assembly monolayer (VSAM) method. Contact angle, surface energy, film thickness, friction force, and roughness were considered for finding the optimized conditions. The sputtered Au/Pd ($\sim$17 nm) layer on the PDMS stamp without the anti-adhesion layer showed poor transfer results due to the high adhesion between sputtered Au/Pd and PDMS. In order to reduce the adhesion between Au/Pd and PDMS, an anti-adhesion monolayer was coated on the PDMS stamp using FOTS (perfluorooctyltrichlorosilane) after $O_2$ plasma treatment. The transfer process with the anti-adhesion layer gave good transfer results over a large area (20 mm $\times$ 20 mm) without pattern loss or distortion. To investigate the applied pressure effect, the PDMS stamp was sandwiched after 90$^{\circ}$ rotation on the MPTMS-coated patterned Si substrate with 1-${\mu}m$ depth. The sputtered Au/Pd was transferred onto the contact area, making square metal patterns on the top of the patterned Si structures. Applying low pressure helped to remove voids and to make conformal contact; however, high pressure yielded irregular transfer results due to PDMS stamp deformation. One of key parameters to success of this transfer process is the controllability of the adhesion force between the stamp and the target substrate. This technique offers high reliability during the transfer process, which suggests a potential building method for future functional structures.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.34D no.4
• /
• pp.33-39
• /
• 1997

The crystallization temperature of an amorphous silicon (a-Si) can be lowered down to 400.deg. C by a new method : Double-metal induced lateral crystallization (DMILC). The a-Si film was laterally crystallized from Ni and Pd deposited area, and its lateral crystallization rate reaches up to 0.2.mu.m/hour at that temperature and depends on the overlap length of Ni and Pd films; the shorter the overlap length, the faster the rate. Poly-Silicon thin film transistors (poly-Si TFT's) fabricated by DMILC at 400.deg. C show a field effect mobility of 38.5cm$^{3}$/Vs, a minimum leakage current of 1pA/.mu.m, and a slope of 1.4V/dec. The overlap length does not affect the characteristics of the poly-Si TFT's, but determines the lateral crystallization rate.