• Journal of the Korean Ceramic Society
• /
• v.31 no.11
• /
• pp.1307-1314
• /
• 1994

The aim of this work is to show the way of manufacturing the SiC mechanical seal at the low temperature of 130$0^{\circ}C$ using clay and frit as source of secondary phase. $\alpha$-SiC and $\beta$-SiC powder which showed different distribution of particle were used as starting materials, i.e. average particle size of $\alpha$-SiC was larger than that of $\beta$-SiC. The mechanical and tribological properties of two groups of specimen, i.e. one contained mainly larger $\alpha$-SiC powder and the other mainly fine particle $\beta$-SiC, were measured. The specimen consisted of larger $\alpha$-SiC exhibited lower density flexural strength and wear resistance is comparison with these of sample containning mainly $\beta$-SiC . This difference could be originated from the dependence of capillary force on the particle size. For the larger SiC particle, the liquid phase may not fill the whole pores during sintering, due to low capillary force, whereas the liquid phase can infiltrate into the small ores surrounded small $\beta$-SiC particle. Thus, the course of high flexural strength and high wear resistance of specimen prepared using small particles can be explaced from the easy infiltration of liquid phase.

• Transactions of Materials Processing
• /
• v.14 no.8 s.80
• /
• pp.681-688
• /
• 2005

The high-temperature deformation mechanisms of a ${\alpha}+{\beta}$ titanium alloy (Ti-6Al-4V), near-a titanium alloy (Ti-6.85Al-1.6V) and a single-phase a titanium alloy (Ti-7.0Al-1.5V) were deduced within the framework of inelastic-deformation theory. For this purpose, load relaxation tests were conducted on three alloys at temperatures ranging from 750 to $950^{\circ}C$. The stress-versus-strain rate curves of both alloys were well fitted with inelastic-deformation equations based on grain matrix deformation and grain-boundary sliding. The constitutive analysis revealed that the grain-boundary sliding resistance is higher in the near-${\alpha}$ alloy than in the two-phase ${\alpha}+{\beta}$ alloy due to the difficulties in relaxing stress concentrations at the triple-junction region in the near-${\alpha}$ alloy. In addition, the internal-strength parameter (${\sigma}^*$) of the near-${\alpha}$ alloy was much higher than that of the ${\alpha}+{\beta}$ alloy, thus implying that dislocation emission/ slip transfer at ${\alpha}/{\alpha}$ boundaries is more difficult than at ${\alpha}/{\beta}$ boundaries.

• Journal of the Korean Ceramic Society
• /
• v.36 no.5
• /
• pp.547-554
• /
• 1999

The self-reinforced Si3N4 ceramics were prepared by pressureless-sintering using ${\beta}$-Si3N4 whiskers as a seed. Effects of ${\beta}$-Si3N4 whiskers on microstructure and mechanical properties and the ${\alpha}$ to ${\beta}$ phase transition of Si3N4 were investigated. The self-reinforced Si3N4 ceramics were densified(relative density$\geq$98%) by pressureless-sintering (1800$^{\circ}C$ 2h) using 8mol% Y2O3 and 6mol% Al2O3 as sintering aids and 5 vol% ${\beta}$-Si3N4 whiskers within self-reinforced Si3N4 ceramic seemed to hinder the densification owing to their acicular shapes but accelerated the ${\alpha}$ to ${\beta}$ phase transition because they acted as pre-existing nuclei. It was found that the more ${\beta}$-Si3N4 nucei the faster ${\alpha}$ to ${\beta}$ phase transition.

• Journal of Korean Neurosurgical Society
• /
• v.42 no.3
• /
• pp.200-204
• /
• 2007

Objective : Radiation therapy is an important treatment for brain tumor. However, serious complications such as radiation necrosis can occur and it may be secondary to the expression of acute phase genes, like cytokines. In particular, inflammatory cytokines (IL-$1{\beta}$, TNF-${\alpha}$) and other immunomodulatory cytokines (TNF-${\alpha}$, TGF-${\beta}1$) might be changed after irradiation (high single dose irradiation). Although it has been reported that IL-1 level is remarkably elevated within 8 week after the irradiation to the rat brain. the change of cytokines levels at acute phase (within 24 hours) has not been reported. In the present study, we examined TNF-${\alpha}$, TGF-${\beta}1$, and IL-$1{\beta}$ levels in acute phase to clarify the early effect of cytokines on the radiation-induced brain damage. Methods : Fifty Sprague-Dawley rats were used and these were divided into irradiation group and control group. After a burr-hole trephination on the right parietal area using a drill, a single 10Gy was irradiated at the trephined site. Their forebrains were extirpated at 30 min, 2 hr, 8 hr, 12 hr and 24 hr, respectively and examined for the expression of TNF-${\alpha}$, TGF-${\beta}1$, and IL-$1{\beta}$. Results : The expression of TNF-${\alpha}$ and TGF-${\beta}1$ were decreased until 12 hr after irradiation but elevated thereafter. The expression of IL-1 was peak at 8 hr and then decreased until 12 hr but elevated after this time window. The present study indicated that expression of cytokines (TNF-${\alpha}$, TGF-${\beta}1$ and IL-$1{\beta}$) were increased at 24 hr after the irradiation to the rat brain. IL-$1{\beta}$ level, on the other hand. reached peak at 8 hr after radiation injury. Conclusion : These findings indicate that IL-1, among various cytokines, may have a more important role in the inflammatory reaction by radiation injury at acute phase and provide some clues for better understanding of the pathogenesis of radiation injury.

• Korean Journal of Materials Research
• /
• v.10 no.9
• /
• pp.636-641
• /
• 2000

The effects of Fe and V content on the characteristics of $\beta$ to $\alpha$ phase transformation for Zr-0.8Sn alloys were studied by optical and transmission electron microscopy. With increasing V content, $\beta{\rightarrow}\alpha+\beta$ transformation temperature decreased, thus allowing the width of $\alpha$-lath to be fine air-cooled Zr-0.8Sn-xV alloys. The width of $\alpha$-lath, however, was slightly increased with Fe content. While the $\beta$ to $\alpha$ transformed microstructures of water-quenched Zr-0.8Sn, Zr-0.8Sn-0.1Fe, Zr-0.8Sn-0.2Fe, Zr-0.8Sn-0.4Fe, Zr-0.8Sn-0.1V and Zr-0.8Sn-0.2V were mainly slipped martensite, that of water-quenched Zr-0.8Sn-0.4V was predominantly twinned martensite. The transition of slipped martensite to twinned martensite in Zr-0.8Sn-Xv was thought to be due to the decrease of $M_S$ temperature.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1433-1435
• /
• 2001

The mechanical and phase transformation of the cold isostatically pressed $\beta$-SiC ceramic were investigated as a function of the sintering temperature. The result of phase analysis revealed 6H, 4H, 3C and phase transformation between 3C and 4H showed over 2000$^{\circ}C$ and the $\beta$ ${\rightarrow}$ $\alpha$ phase transformation was in saturation at 2200$^{\circ}C$. The relative density and the mechanical properties of $\alpha$-SiC ceramic was increased with increased sintering temperature. The flexural strength showed the highest value of 230 MPa at 2200$^{\circ}C$. This reason is because crack was propagated through surface flaw. The fracture toughness showed the highest value of 4.2 $MPa{\cdot}m^{1/2}$ at 2200$^{\circ}C$.

• Resources Recycling
• /
• v.11 no.6
• /
• pp.31-37
• /
• 2002

Microstructure of aluminum alloys produced by the different mixing ratio of secondary ingot made by aluminum UBC (used beverage can) and virgin aluminum was investigated. The phase transitions of casted ingot by heat treatment were also studied. The alloys were melted at the electric resistance furnace, then casted using ceramic filter. Homogenization heat treatment was conducted at $615^{\circ}C$ for 10hrs to control cast microstructure. There were several kinds of phases, in as-cast condition, such as $\alpha$($Al_{12}$ $((Fe,Mn)_3$Si), $\beta$($Al_{6}$ (Fe,Mn)), and fine $Mg_2$Si phases. Especially, the amount of $\beta$-phase which was harmful in forming process was large. The $\beta$-Phase formed was transformed to u-phase by heat treatment. The fine $Mg_2$Si in the aluminum matix was also transformed to $\alpha$-phase by this heat treatment. Impurities filtered during casting process were identified as intermetallic compounds of Fe, Cu, Si.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.230-230
• /
• 2010

유기물 반도체 화합물인 Cu-Pc(copper(II)-phthalocyanine)는 우수한 전기적 광학적 특성을 가지며, OLED, MISFET등 소자로서의 활용도가 높다. Cu-Pc 화합물은 $\alpha$-phase, $\beta$-phase, $\gamma$-phase를 포함하는 여러 가지 다결정 polymer로 존재할 수 있다. 가장 잘 알려진 구조로는 열적으로 준안정적인 $\alpha$-phase와 열적으로 안정적인 $\beta$-phase가 있다. Cu-Pc 박막의 구조 및 흡수 특성과 전기적 특성에 대한 기술이 확실히 규명되지 않아 본 연구에서는 두께와 열처리 조건에 따른 결정성 및 방향성을 조사하기 위하여 $\alpha$-phase와 $\beta$-phase의 phase transition 현상 및 전기적 광학적 특성을 규명 하고자 한다. 진공증착 방법 중 하나인 PVD 방법의 thermal evaporation deposition을 이용하여 glass, ITO 기판위에 두께와 열처리에 따른 전기적?광학적 특성을 연구하였다. Cu-Pc 박막의 성장두께는 5nm~50nm 이내로 fluxmeter 및 thickness monitor를 이용하여 제어하였다. 5nm~50nm의 두께에 따른 기판온도를 $200^{\circ}C$로 고정하여 전열 처리 및 후열 처리하여 온도에 따른 박막을 성장한 후, 결정 구조 및 특성 변화와 phase transition 분석하였다. 제작된 Cu-Pc의 박막은 $\alpha$-phase와 $\beta$-phase로 구분할 수 있으며, 열처리에 따른 phase transition 현상이 뚜렷함을 알 수 있다. XRD(X-ray diffraction)를 통하여 박막에 대한 결정 구조 분석 및 FE-SEM(field emission scanning electron microscopy)와 AFM(atomic force microscopy)을 이용하여 Cu-Pc 박막의 구조적 결정성과 방향성 등, 표면 상태와 형상구조에 대해 표면의 특성을 측정하며, 광 흡수도(UV-visible absorption spectra)을 이용하여 phase transition 현상에 따른 I-V 특성을 비교분석 하였다.

• Journal of Korea Foundry Society
• /
• v.9 no.1
• /
• pp.58-66
• /
• 1989

The effect of heat treating temperature and ${\alpha}$ phase In the ${\beta}$ phase matrix were investigated for ${\beta}-CuZnAl$ shape memory alloys by tension test, fatigue test, and shape memory effect test. After heat treatment at $677^{\circ}C$, $750^{\circ}C$, $800^{\circ}C$ and $850^{\circ}C$ for 10 min. respectively, static fracture stress(${\sigma}_f$), fatigue fracture stress(${\tau}_{max}$) at $10^6$ cycle, and elongation(${\epsilon}_f$) was $24.2kg/mm^2$, $17.21kg/mm^2$ and 11.8%, respectively. As heat treating temperature decreased, fracture surfaces of the specimens were changed from the intergranular to the transgranular fracture mode. Especially, the a phase precipitated in the ${\beta}$ phase matrix had an effect on crack propagation and the fracture surface was characterized by dimple-like pattern when crack propagated in transgranular cracking mode. Precipitation of the ${\alpha}$ phase in the ${\beta}$ phase matrix lowered the transformation temperature by $10^{\circ}C$, and about 2.5 vol.% ${\alpha}$ phase did not affect the shape memory effect examined by the bending test.

• Korean Journal of Metals and Materials
• /
• v.50 no.2
• /
• pp.164-170
• /
• 2012

Nanotubular structure formation on the Ti-6Al-4V and Ti-Ta alloy surfaces by electrochemical methods has been studied using the anodizing method. A nanotube layer was formed on Ti alloys in 1.0 M $H_3PO_4$ electrolyte with small additions of $F^-$ ions. The nanotube nucleation and growth of the ${\alpha}$-phase and ${\beta}$-phase appeared differently, and showed different morphology for Cp-Ti, Ti-6Al-4V and Ti-Ta alloys. In the ${\alpha}$-phase of Cp-Ti and martensite ${\alpha}^{\prime}$ and in the ${\alpha}^{{\prime}{\prime}}$ and ${\beta}$-phase of the Ti-Ta alloy, the nanotube showed a clearly highly ordered $TiO_2$ layer. In the case of the Ti-Ta alloy, the pore size of the nanotube was smaller than that of the Cp-Ti due to the ${\beta}$-stabilizing Ta element. In the case of the Ti-6Al-4V alloy, the ${\alpha}$-phase showed a stable porous structure; the ${\beta}$-phase was dissolved entirely. The nanotube with two-size scale and high order showed itself on Ti-Ta alloys with increasing Ta content.