In this paper, the real scenario of water situation (e.g. water management, water availability and flooding) in an irrigated rice cultivation area in Suphanburi Province, Central-West Thailand is discussed together with the NDVI time series data. The result shown is derived by our classifier named 'Peak Detector Algorithm (PDA)'. The method discriminated 5 classes in terms of irrigation activities and cropping intensities, namely, Non-irrigated, Poorly irrigated - 1 crop/year, Irrigated - 2 crops/year, Irrigated - 3 crops/year and Others (no cultivation happens in a year or other land covers). The overall accuracy of all classified results (1999-2001) is around $77\%$ against independent ground truth data (general activities or function of an area). In the classified results, spatial and temporal inconsistency appeared significantly in the Western and Southern areas of Suphanburi. The inconsistency resulted mainly by anomaly of rainfall pattern in 1999 and their temporal irrigation activity. The algorithm however, was proved that it could detect actual change of irrigation status in a year.

Plant water deficiency during drought season causes physiological stress and can be a critical indicator of forest fire vulnerability. In this study, we attempt to analyze the spectral characteristics of water stressed vegetation by using the laboratory measurement on leaf samples and the canopy reflectance spectra extracted from satellite hyperspectral image data. Leaf-level reflectance spectra were measured by varying moisture content using a portable spectro-radiometer. Canopy reflectance spectra of sample forest stands of two primary species (pine and oak) located in central part of the Korean peninsula were extracted from EO-l Hyperion imaging spectrometer data obtained during the drought season in 2001 and the normal precipitation year in 2002. The preliminary analysis on the reflectance spectra shows that the spectral characteristics of leaf samples are not compatible with the ones obtained from canopy level. Although moisture content of vegetation can be influential to the radiant flux reflected from leaf-level, it may not be very straightforward to obtain the spectral characteristics that are directly related to the level of canopy moisture content. Canopy spectra form forest stands can be varied by structural variables (such as LAt, percent coverage, and biomass) other than canopy moisture content.

The Third Assessment Report of the Intergovernmental Panel on Climate Change (IPCC) concluded that many collective observations gave a aspect of a global warming and other changes in the climate system. Future earth observation using satellite data should monitor global climate change, and should contribute to social benefits. Especially, human activities has given the big impacts to earth environment This is a very complex affair, and nature itself also impacts the clouds, namely the seasonal variations. JAXA (former NASDA) has the plan of the Global Change Observation Mission (GCOM) for monitoring of global environmental change. SGLI (Second Generation GLI) onboard GCOM-C (Climate) satellite, which is one of this mission, is an optical sensor from Near-UV to TIR. This sensor is the GLI follow-on sensor, which has the various new characteristics. Polarized/multi-directional channels and 250m resolution channels are the unique characteristics on this sensor. This sensor can be contributed to clarification of coastal change in sea surface. This paper shows the introduction of the unique aspects and characteristics of the next generation satellite sensor, SGLIIGCOM-C, and shows the preliminary research for this sensor.

Global latent heat flux data sets are crucial for many studies such as those related to air-sea interaction and climate variation. Currently, various global latent heat flux data sets are constructed using satellite data. Japanese Ocean Flux data sets with Use of Remote sensing Observations (J-OFURO) includes one of the satellite-derived global latent heat flux data (Kubota et aI., 2000). In this study, we review future development of J-OFURO global latent heat flux data set. In particular, we investigate usage of multi-satellite data for estimating accurate global latent heat flux. Accurate estimation of surface wind speeds over the global ocean is one of key factors for the improved estimation of global latent heat flux. First, we demonstrate improvement of daily wind speed estimation using multi-satellites data from microwave radiometers and scatterometers such as DMSP/SSMI, ERS/AMI, QuikSCAT/SeaWinds, AqualAMSR-E, ADEOS2/AMSR etc. Next, we demonstrate improvement of global latent heat flux estimation using the wind speed data derived from multi-satellite data.

The impact of the interannual climatic variability on the vegetation sensitively appears in the timing of phenological events such as green-up, mature, and senescence. Therefore, an accurate and temporally high-resolution NDVI dataset will be required for analysis on the interannual variability of the climate-vegetation relationship. We constructed a daily 8km NDVI dataset over Eurasia based on the 8km tiled data of Pathfinder A VHRR Land (PAL) Global daily product. Cloud contamination was successfully reduced by Temporal Window Operation (TWO), which is a method to find optimized upper envelop line of the NDVI seasonal change. Based on the daily NDVI time series from 1982 to 2000, an accurate (daily) interannual change of the phenological events will be analyzed.

The 10 Year Implementation Plan for a Global Earth Observation System of Systems (GEOSS), which was endorsed at the Third Earth Observation Summit in Brussels in February, 2005, emphasizes the importance of data management facilities for diverse and large-volume Earth Observation data from inhomogeneous information sources. A three year research plan for addressing this key target of GEOSS has just approved as the first step by the Japanese government. The goals of this research are, (1) to develop a data management core system consisting of data integration and information fusion functions and interoperability and information service functions; (2) to establish data and information flows between data providers and users; (3) to promote application studies of data integration and information fusion, especially in the fields of weather forecasting, flood forecasting, agricultural management, and climate variability and changes. The research group involves leading scientists on information science and technology, who have been developing giant data archive servers, storage area networks, metadata models, ontology for the earth observations. They are closely cooperating with scientists on earth sciences, water resources management, and agriculture, and establishing an effective collaborative research framework.

In order to compute cloud coverage statistics over Asian region, an operational scheme for masking cloud-contaminated pixels in Advanced Very High Resolution Radiometer (AVHRR) daytime data was developed, evaluated and presented. Dynamic thresholding was used with channell, 2 and 3 to automatically create a cloud mask for a single image. Then the IO-day cloud coverage imagery was generated over the whole Asian region along with cloud-free composite imagery. Finally the monthly based statistics were computed based on the derived cloud coverage imagery in terms of land cover and country. As a result, it was found that 20-day is required to acquire the cloud free data over the whole Asia using NOAA AVHRR. The to-day cloud coverage and cloud-free composite imagery derived in this research is available via the web-site http://webpanda.iis.u-tokyo.ac.jp/CloudCover/.

Though sensible heat flux is one of heat flux components, it is generally considered that the importance is low compared with other components because of the small value. Actually sensible heat flux over the tropical ocean is extremely small, less than $100\;W/m^2$ .. However, it should be noted that sensible heat flux in boreal winter over the western boundary current regions is considerably large, about $100\;W/m^2$, and not neglected. In this study we carry out intercomparison of various global sensible heat flux data including not only satellite-derived data but also reanalysis data in order to clarify the characteristics of those data.

An efficient and robust neural network-based scheme is introduced in this paper to perform automatic cloud detection. Unlike many existing cloud detection schemes which use thresholding and statistical methods, we used the artificial neural network methods, the multi-layer perceptrons (MLP) with back-propagation algorithm and radial basis function (RBF) networks for cloud detection from Geostationary satellite images. We have used a simple scene (a mixed scene containing only cloud and clear sky). The main results show that the neural networks are able to handle complex atmospheric and meteorological phenomena. The experimental results show that two methods performed well, obtaining a classification accuracy reaching over 90 percent. Moreover, the RBF model is the most effective method for the cloud classification.

The observation data from MTP-5HE ofEPA are used to study the temperature inversion phenomenon in the lower boundary layer in Taipei, Taichung and Kaohsiung of Taiwan. Characteristics of temperature inversion at three cities are extracted using different classification methods. The characteristics of temperature inversion in Taichung and Kaohsiung show a similar trend but are different from that in Taipei. The numbers of the occurrence of temperature inversion in Taichung and Kaohsiung were much larger than that in Taipei. The main types of temperature inversion in Taiwan are radiation inversion and frontal inversion. Compared to frontal inversion, radiation inversion on average occurs at a lower altitude, lasts a longer period, has a deeper thickness, and reaches a higher temperature difference of inversion. Frontal inversion plays a significant role for the inversion event lasting over 12 hours.

[1] There are systematical errors associated with ionospheric influence in retrieving key atmospheric parameters from radio occultation (RO) soundings. In order to obtain better-quality retrievals, we develop a new method, hereafter called National Central University Radio Occultation (NCURO) scheme, to reduce the ionospheric influence. The excess phase is divided into two parts, namely geometric excess length and path excess length (excess length along ray path due to refractivity effect). An excess phase equation is presented and implemented in the NCURO scheme Whose performance is evaluated through comparisons with model simulation and experimental data. The model simulation is based on the use of the ionospheric model 002001 and atmospheric model NRLMSISE-OO. Results show that the NCURO scheme significantly reduces the ionospheric influence at altitudes above 70 km as does the scheme presented in the literature, and provides better corrections for the atmospheric profile. INDEX TERMS: 2400 Ionosphere: Ionosphere; 6964 Radio Science: Radio wave propagation; 6969 Radio Science: Remote sensing.

Using satellite images, an optimal solution to water motion has been presented in this study. Since temperature patterns are suitable tracers in water motion, Sea Surface Temperature (SST) images of Caspian Sea taken by MODIS sensor on board Terra satellite have been used in this study. Two daily SST images with 24 hours time interval are used as input data. Computation of templates correspondence between pairs of images is crucial within motion algorithms using non-rigid body objects. Image matching methods have been applied to estimate water body motion within the two SST images. The least squares matching technique, as a flexible technique for most data matching problems, offers an optimal spatial solution for the motion estimation. The algorithm allows for simultaneous local radiometric correction and local geometrical image orientation estimation. Actually, the correspondence between the two image templates is modeled both geometrically and radiometrically. Geometric component of the model includes six geometric transformation parameters and radiometric component of the model includes two radiometric transformation parameters. Using the algorithm, the parameters are automatically corrected, optimized and assessed iteratively by the least squares algorithm. The method used in this study, has presented more efficient and robust solution compared to the traditional motion estimation schemes.

Time series of gridded surface wind and wind-stress vectors over the world ocean have been constructed by satellite scatterometer data. The products are derived from the ERS-l,2 covering 9 years during 1992-2000 and the Sea Winds on board QuikSCAT (Qscat) which has been operating up to the present since June 1999, so they allows us to analyze variabilities with various time scales. In this study, we focus on interannual variability of the wind stress in the mid- and high-latitude region of North Pacific. These are compared with those by numerical weather prediction(NWP) ones (NCEP Reanalysis). We also examine variability in the wind-stress curl field that is an important factor for ocean dynamics and focus its time and spatial characters in the northwestern Pacific around Japan. It is found that the vorticity field in the lower atmosphere tends to increase gradually with time, suggesting the enhancement of the North Pacific subtropical gyre.

This study examines moisture supplement from the warm ocean in snowfalls of two cases and heavy rainfall of Typhoon case. The QuickSCAT wind is used to evaluate the convergence of moisture fluxes in the storms from the sea in estimation of the amount of heavy snowstorm and rainfall. The results show that enough water vapor transport from ocean to atmosphere induced the severe storms, because strong QuickSCAT -derived vertical velocity nearly concurred with heavy snowfall and rainfall. In the present study, we attempted to show that QuickSCAT wind can be used to forecast the severe weather events, such as heavy snowfall and rainfalls.

The purpose of this paper is to take a closer look at an area having shorted emergence facilities and to determine optional candidate sites instead of vulnerable area by using GIS spatial analysis. Newly determined new candidate is performed by concerning spatial efficiency and spatial equity for a public service. It was determined through using the analyzing of the physical accessibility measure, the Location-Allocation, sort of classic model in spatial statistics and general network analysis. The area of this research has been used in administrative boundary of Young-Dong in Gangneung including 13 emergency, medical hospitals, 46 fire-stations and sub-fire stations. In general terms, what all this show is that the way we are approached for geographical view from using GIS spatial analyzing technique of determined location and allocation problem by the social, economical, political factor and simple administrative discrimination at the meantime. At the same time, with problem occurred in the space it is possible to make an Effective proposal or means, policy, decision for new candidate location-allocation suggesting optimum model.

In order for effective disaster prevention, it is necessary to have some idea of when, where, why and what kind of weather disasters may occur, and how large they may be. But the regional characteristics of Shizuoka Prefecture from the viewpoint of weather disasters have not been studied before. In this study, the authors gathered the data which represent how many times weather disasters occurred in Shizuoka Prefecture in the last fourteen years, and then divided it into some regions using a multivariate analysis. The authors adopted principal component analysis on this data, and then adopted cluster analysis with principal component scores which must be significant in the previous analysis. Finally the authors set the regional division based on these clusters and described the regional characteristics. This study could contribute to the weather disaster prevention in Shizuoka Prefecture.

Earthquake disaster frequently happens in Shizuoka Prefecture and it is commonly predicted that a giant earthquake(Tokai Earthquake) could occur in the near future. When a giant earthquake happens, extensive damage of lifelines will be expected. It is considered that the collection of damage information and the establishment of a communication network system are very important in order to restore lifelines quickly. And geographic information system(GIS) might playa very important role to grasp the spatial information of lifeline damage in a natural disaster. The authors' group had a research project to study a lifeline restoration support system with image processing and ad hoc networking in a natural disaster. The objectives of this presentation are to introduce our project and to show some results of our study. The authors finally constructed the GIS for the integration of damage information acquired by image processing and ad hoc networking.

Uncertainty of objects in Moving Object Database is a coherent property. It has been discussed in a lot of researches on modelling and query processing. The previous studies assume that uncertain future time is determined through utilizing recent speed and direction of vehicles. This method is simple and useful for estimating the time of the near future location. However, it is not appropriate when we estimate the time of the far future location. Therefore, in this paper, we propose a concept of planned route. It is used to estimate uncertain future time, which has to be located at a given point. If the route of an object is planned beforehand its locations are uncertainly distributed near that route. By a simple projection operation, the probability that a location lies in the planned route is increased. Moreover, we identify the future time of an object based on the speed for passing the route, which is offered via a website.

When the data from the artificial satellite is analyzed, recent years it is perceived to vegetation index using BRF(Bidirectional Reflectance Factor) of the observation target. To make the BRF models, it is important to measure the 3D structure of the observation target actually. In this study, it is proposed to the observation technique by using laser scanning data. Also, our team has been operating the radio controlled helicopter which can fly over the tall forest canopy and it can be equipped the measurement system.

Recently the necessity of road data is still being increased in industrial society, so there are many repairing and new constructions of roads at many areas. According to the development of government, city and region, the update and acquisition of road data for GIS (Geographical Information System) is very necessary. In this study, the fusion method with range data(3D Ground Coordinate System Data) and Intensity data in stand alone LiDAR data is used for road extraction and then digital image processing method is applicable. Up to date Intensity data of LiDAR is being studied. This study shows the possibility method for road extraction using Intensity data. Intensity and Range data are acquired at the same time. Therefore LiDAR does not have problems of multi-sensor data fusion method. Also the advantage of intensity data is already geocoded, same scale of real world and can make ortho-photo. Lastly, analysis of quantitative and quality is showed with extracted road image which compare with I: 1,000 digital map.

This paper presents a method for point-based 3D building reconstruction using LiDAR data and digital map. The proposed method consists of three processes: extraction of building roof points, identification of roof types, and 3D building reconstruction. After extracting points inside the polygon of building, the ground surface, wall and tree points among the extracted points are removed through the filtering process. The filtered points are then fitted into the flat plane using ODR(Orthogonal Distance Regression). If the fitting error is within the predefined threshold, the surface is classified as a flat roof. Otherwise, the surface is fitted and classified into a gable or arch roof through RMSE analysis. Based on the roof types identified in automated fashion, the 3D building reconstruction is performed. Experimental results showed that the proposed method classified successfully three different types of roof and that the fusion of LiDAR data and digital map could be a feasible method of modelling 3D building reconstruction.

The FORMOSAT-3/COSMIC mission is a micro satellite mission to deploy a constellation of six micro satellites at low Earth orbits. The final mission orbit is of an altitude of 750-800 lan. It is a collaborative Taiwan-USA science experiment. Each satellite consists of three science payloads in which the GPS occultation experiment (GOX) payload will collect the GPS signals for the studies of meteorology, climate, space weather, and geodesy. The GOX onboard FORMOSAT -3 is designed as a GPS receiver with 4 antennas. The fore and aft limb antennas are installed on the front and back sides, respectively, and as well as the two precise orbit determination (POD) antennas. The precise orbit information is needed for both the occultation inversion and geodetic research. However, the instrument associated errors, such as the antenna phase center offset and even the different cable delay due to the geometric configuration of fore- and aft-positions of the POD antennas produce error on the orbit. Thus, the focus of this study is to investigate the impact of POD antenna parameter on the determination of precise satellite orbit. Furthermore, the effect of the accuracy of the determined satellite orbit on the retrieved atmospheric and ionospheric parameters is also examined. The CHAMP data, the FORMOSAT-3 satellite and orbit parameters, the Bernese 5.0 software, and the occultation data processing system are used in this work. The results show that 8 cm error on the POD antenna phase center can result in ~8 cm bias on the determined orbit and subsequently cause 0.2 K deviation on the retrieved atmospheric temperature at altitudes above 10 lan.

A numerical formula that presents relationship between a point of a satellite image and its ground position is called a sensor model. For precise geolocation of satellite images, we need an error-free sensor model. However, the sensor model based on GOES ephemeris data has some error, in particular after Image Motion Compensation (IMC) mechanism has been turned off. To solve this problem, we investigate three sensor models: Collinearity model, Direct Linear Transform (DLT) model and Orbit-based model. We apply matching between GOES images and global coastline database and use successful results as control points. With control points we improve the initial image geolocation accuracy using the three models. We compare results from three sensor models that are applied to GOES-9 images. As a result, a suitable sensor model for precise geolocation of GOES-9 images is proposed.

Communication, Ocean, and Meteorological Satellite (COMS) to be launched in year 2008 will be the first Korean multi-purpose geostationary satellite aiming at three major missions, i.e.: communication, ocean, and meteorological applications. The development of systems for the meteorological mission sponsored by the Korea Meteorological Administration (KMA) consists of payloads, ground system, and data processing system. The program called COMS Meteorological Data Processing System (CMDPS) has been initiated for the development of data processing system. The primary objective ofCMDPS is to derive the level-2 environmental products from geo-Iocated and calibrated level 1.5 COMS data. Preliminary design for the level-2 data processing system consists of 16 baseline products and will be refined by end of 3rd project year. Also considered for the development are the necessary initial information such as land use and digital elevation map, algorithms for the vicarious calibration and procedures for the calibration monitoring, and radiative transfer model. Here, we briefly introduce the overall development strategy, flow chart for the intended baseline products, a few preliminary algorithm results and future plans.

This paper describes link analysis on the processed data, HRIT (High Rate Information Transmission) and LRIT (Low Rate Information Transmission), for the preliminary design of interface between COMS (Communication, Ocean and Meteorological Satellite) and ground station. At the MODAC (MeteorologicaVOcean Data Application Center), the processed data are transmitted to user station via COMS with normalization and calibration by pre-processing of MI (Meteorological Imager) data. Due to consider satellite as radio relay, overall analysis containing uplink and downlink is needed. Specific link parameters can be obtained with using the outcomes of SRR (System Requirement Review) which was held on 13-14 June 2005, in Toulouse. From the relation between overall link margin and output power of HPA (High Power Amplifier) of MODAC, it is shown that even though the minimum power related with COMS receiving power range is transmitted at MODAC, the obtained link margin of HRIT could be above 3 dB at user station which antenna elevation angle is 10 degree.

Vicarious calibration method using MODIS-derived surface reflectivity data as inputs to a radiative transfer model have been developed for the planned COMS solar channel. Pilot test was conduced over the Simpson Desert targets in Australia. Results suggested that calibration can be achieved within $5\%$ error range.

COMS(Communication, Ocean, and Meteorological Satellite) is the geostationary satellite for the mission of satellite communication, ocean monitoring, and meteorological service. It is scheduled to be launched at the end of 2008. Ocean payload of COMS named as GOCI(Geostationary Ocean Color Imager) observes ocean color and derives the chlorophyll concentrlition, the concentration of dissolved organic material and so on. In operational oceanography, satellite derived data products are used to provide forecasting and now casting of the ocean and coastal water state. In this work, conceptual design of structural part of GOCI is carried out and two baseline concepts are proposed. The one is dioptric module that uses lens system and the other is TMA(Three Mirror Anastigmat) module that uses mirror system. Trade-off studies between two concepts are investigated by considering optical and mechanical performances. Finally, on-going tasks and future development plan are briefly discussed.

The Communication Ocean, Meteorological Satellite (COMS) as the one of the national space program has been developed by Korea Aerospace Research Institute (KARl). The Geostationary Ocean Color Imager (GOCI) is one of the main payloads ofCOMS which will provide consistent monitoring of ocean-colour around the Korean Peninsula from geostationary platforms. The ocean color observation from geostationary platform is required to remedy the coverage constraints imposed by polar orbiting platforms. In this paper the main characteristics of GOCI are described and compared with the current ocean color sensors. The GOCI will provide the measurement data of 6 visible channels and 2 nearinfrared channels (40Onm - 900nm). The high radiometric sensitivity is essential of ocean color sensor because of the weak water leaving radiance.

Communication Ocean Meteorological Satellite (COMS) for the hybrid mission of meteorological observation, ocean monitoring, and telecommunication service is planned to be launched onto Geostationary Earth Orbit in 2008. The meteorological payload of COMS is an imager which will monitor meteorological phenomenon around the Korean peninsular intensively and of Asian-side full Earth disk periodically. The meteorological imager (MI) of COMS has 5 spectral channels, I visible channel with the resolution of I km at nadir and 4 infrared channels with the resolution of 4 km at nadir. The characteristics of the COMS MI are introduced in the view points of user requirements, hardware characteristics, and operation features.

As to the synthetical estimation of land covering parameters or the compounded land covering classification for multi-resolution satellite data, former researches mainly adopted linear or nonlinear regression models to describe the regression relationship of land covering parameters caused by the degradation of spatial resolution, in order to improve the retrieval accuracy of global land covering parameters based on 1;he lower resolution satellite data. However, these methods can't authentically represent the complementary characteristics of spatial resolutions among different satellite data at arithmetic level. To resolve the problem above, a new compounded land covering classification method at arithmetic level for multi-resolution satellite data is proposed in this .paper. Firstly, on the basis of unsupervised clustering analysis of the higher resolution satellite data, the likelihood distribution scatterplot of each cover type is obtained according to multiple-to-single spatial correspondence between the higher and lower resolution satellite data in some local test regions, then Parzen window approach is adopted to derive the real likelihood functions from the scatterplots, and finally the likelihood functions are extended from the local test regions to the full covering area of the lower resolution satellite data and the global covering area of the lower resolution satellite is classified under the maximum likelihood rule. Some experimental results indicate that this proposed compounded method can improve the classification accuracy of large-scale lower resolution satellite data with the support of some local-area higher resolution satellite data.

With the commercial availability of very high resolution satellite imagery, the concealment of national confidential targets such as military facilities became one of the most bothering task to the image distributors. This task has been carried out by handwork masking of the target objects. Therefore, the quality of the concealment was fully depends on the ability and skill of a worker. In this study, a spectral clustering based technique for the seamless concealment of confidential targets in high resolution imagery was developed. The applicability test shows that the proposed technique can be used as a practical procedure for those who need to hide some information in image before public distribution

Many researchers conducted the effort for improving the classification accuracy of satellite image. Most of the study has used optical spectrum information of each pixel for image classification. By applying this method for high resolution satellite image, number of class becomes increase. This situation is remarkable for house, because the roof of house has variety of many colors. Even if the classification is carried out for many classes, roof color information of each house is not necessary. Most of the case, we need the information that object is house or not. In this study, we propose the method for detecting the object by using Genetic Algorithms (GA). Aircraft was selected as object. It is easy for this object to detect in the airport. An aircraft was taken as a template. Object image was taken from QuickBird. Target image includes an aircraft and Haneda Airport. Chromosome has four or five parameters which are composed of number of template, position (x,y), rotation angle, rate of enlarge. Good results were obtained in the experiment.

Change detections is carried out under the assumption that pixel boundaries of geometrically corrected time series satellite images cover the same location. However that assumption can be wrong when shifts in the pointing direction of a satellite sensor occurs. Currently, although the influence of misregistration on landcover change detection has been investigated, there has been little research on the influence of pointing direction shifts of a satellite sensor. In this study, a simple method for reducing the effects of pointing direction shifts of a satellite sensor is proposed: the classification of two ASTER images was carried out using the linear spectral mixture analysis, the two classification results were resampled into a geometrically fixed grid, and then the change detection of the two ASTER images was carried out by comparing the resampled classification results of the two images. The proposed method showed high performance in discriminating between changed areas and unchanged areas by removing the pointing direction shifts of a satellite sensor.

This paper presents the efficient method to detect the defective detectors of the SWIR band of SPOT 4. The key of this method are to flatten the baseline of the data using high pass band filter instead of differentiation. This method is made up six steps. First step is to apply image enhancement techniques to enhance the lines imaged by defective detector and improve the quality of an image. Second step is processed by summing the enhanced image in line direction. These summed data have the peaks that represent the defective detectors and the curved baseline characterized by the reflectivity of Earth surface. In order to exactly detect these peaks, third step is to flatten the curved baseline using high pass filtering in the frequency domain. In fourth step, the data with flat baseline is normalized to have zero mean and unity standard deviation. In fifth step, the defective detectors are detected using $99.9\%$ confidence interval. Finally, after removing the detected ones in summed data, the steps from third to five are iterated. Three SPOT 4 images, which have different reflectivity of Earth surface and different sensor, were used to validate this method. The overall accuracy of detection for three images was $97.9\%$. This result shows that this method can detect efficiently the lines made by defective detectors.

Unsupervised spectral angle classification (USAC) is the algorithm that can extract ground object information with the minimum 'Spectral Angle' operation on behalf of 'Spectral Euclidian Distance' in the clustering process. In this study, our algorithm uses the unit vector instead of the spectral distance to compute the mean of cluster in the unsupervised classification. The proposed algorithm (MUSAC) is applied to the Hyperion and ETM+ data and the results are compared with K-Meails and former USAC algorithm (FUSAC). USAC is capable of clearly classifying water and dark forest area and produces more accurate results than K-Means. Atmospheric correction for more accurate results was adapted on the Hyperion data (Hyperion-FLAASH) but the results did not have any effect on the accuracy. Thus we anticipate that the 'Spectral Angle' can be one of the most accurate classifiers of not only multispectral images but also hyperspectral images. Furthermore the cluster unit vector can be an efficient technique for determination of each cluster mean in the USAC.

In this paper, we propose a watermarking technique of multispectral images. In our method, the Principal Component Analysis (PCA) is preliminarily applied on the multispectral image. The most principal component image is used for embedding with a watermark, which is a pseudo-random number sequence generated with a secret key. The embedding process is performed in the wavelet domain. The resulting image is then reinserted into the principal component images, and the final multispectral image containing the watermark can be produced by the inverse PCA. Experimental results are provided to illustrate the performance of the algorithm against various kinds of attacks.

Since the successful launch of FORMOSAT -2 satellite by National Space Organization of Taiwan in May 2004, the Remote Sensing Instrument (RSI) on- board the FORMOSAT -2 has continuously acquired images at one panchromatic and four multi-spectral bands (http://www.nspo.org.tw). In general, the RSI performs well and receives high quality images which proved to be very useful for various applications. However, some RSI panchromatic products exhibit obvious trembling artifact that must be removed. Preliminary study reveals that the trembling artifact is caused by the instability of the spacecraft attitude. Though the magnitude of this artifact is actually less than half of a pixel, it affects the applicability of panchromatic products. A procedure removing this artifact is therefore needed for providing image products of consistent quality. Due to the nature of trembling artifact, it is impossible to describe the trembling amount by employing an analytic model. Relied only on image itself, an algorithm determining trembling amount and removing accordingly the trembling artifact is proposed. The algorithm consists of 3 stages. First, a cross-correlation based scheme is used to measure the relative shift between adjacent scan lines. Follows, the trembling amount is estimated from the measured value. For this purpose, the Fourier transform is utilized to characterize random shifts in frequency domain. An adaptive estimation method is then applied to deduce the approximate trembling amount. In the subsequent stage, image re-sampling operation is applied to restore the trembling-free product. Experimental results show that by applying the proposed algorithm, the unpleasant trembling artifact is no longer evident.

This study investigates to detect sea surface temperature (SST) and land cover change after tide embankment construction using Landsat Thematic Mapper (TM) thermal infrared (TIR) band data at Shihwa Lake and surrounding area. SST measurement is important for studies of both the structure of the ocean and as the thermal boundary between the ocean and the atmosphere. The TIR band of TM images can be used to detect SST change whose shoreline is complicated and narrow like the study site. The purpose of this study is to estimate SST and land cover change at Shihwa Lake and surrounding area.

A new methodology to detect forest fire burnt scars at near real time using MODIS (Moderate-resolution Imaging Spectroradiometer) data is presented here with a goal of introducing a new and improved capability to detect forest fire burnt scars in Thailand. This new technology is expected to increase the efficiency and effectiveness of the forest fire tackling resources distribution and management of the country. Using MODIS data in burnt scars detection has two major advantages - high availability of data and high resolution per performance ratio. Results prove the near real time algorithm suitable and working well in order to monitor the forest fire dynamic movement. The algorithm is based on the threshold separated linear equation of burnt and un-burnt. A ground truth experiment confirms the burnt and un-burnt? areas characteristics (temperature and NDVI). A threshold line on a scatter plot of Band I and Band 2 is determined to separate the burnt from un-burnt pixels. The different threshold values of NDVI and temperature use to identify pixels' anomaly, abnormal low NDVI and high temperature. The overlay (superimpose) method is used to verify burnt pixels. Since forest fire is a dynamic phenomenon, MODIS burnt scars information is suiting well to fill in the missing temporal information of LANDSAT for the forest fire control managing strategy in Thailand. This study was conducted in the Huai-Kha-Kaeng (HKK) Wildlife Sanctuary, Thailand

The paper presents time and cost effective remote sensing technology to estimate recharge potential of fresh water shallow aquifers for their sustainable management in arid ecosystem. Precipitation measurement of Raudatain Basin in Kuwait from TRMM data has been made and integrated with geological, geomorphological and hyrological data, to estimate the recharge potential of the basin. The total potential recharge to the area is estimated as 333.964 MCM annually. The initial losses are estimated at $60\%$ of the net precipitation .The net available quantity for recharge is 133.58 MCM. For sustainable management of the ground water resources, recharge wells have been proposed in the higher order streams to augment the Raudatain aquifer in Kuwait. If the available quantity of precipitation can be successfully utilized, it will reduce considerable pressure on desalination, which is leading to increased salinity off the coast in Arabian Gulf.

In this study, emissivity and land surface temperature (LST) were retrieved using the previously developed algorithms and Aqua/MODIS data. And sensitivity of estimated emissivity and LST to the predefined values, such as land cover, normalized difference vegetation index (NOVI) and spectral emissivity were investigated. The methods used for emissivity and LST were vegetation cover method (VCM) and four different split-window algorithms. The spectral emissivity retrieved by VCM was not sensitive to the NOVI error but more sensitive to the land cover error. The comparison of LST showed that the LST was systematically different without regard to the land cover and season. And the LST was very sensitive to the emissivity error excepting the Uliveri et al. This preliminary result indicates that more works are needed for the retrieval of reliable LST from satellite data.

Modem SAR interferometry (IFSAR) sensors delivering intensity images and corresponding digital terrain model (DTM) allow for a thorough surface lineament interpretation with the all-weather day-night applicability. In this paper, an automatic linear-feature detection algorithm for high-resolution SAR images acquired in Taiwan is proposed. Methodologies to extract linear features consist of several stages. First, the image denoising techniques are used to remove the speckle noise on the raw image. In this stage, the Lee filter has been chosen because of its superior performance. After denoising, the Coefficient of Variation Detector is performed on the result images for edge enhancements and detection. Dilation and erosion techniques are used to reconnect the fragmented lines. The Hough transform, which is a special case of a more general transform known as Radon transform, is a suitable method for line detection in our analysis. Finally, linear features are extracted from the binary edge image. The last stage contains many substeps such as edge thinning and curve pruning.

The purpose of this study is to analyze the principal causes of increases in air temperature on platforms of railway station. We analyzed the distribution of air temperature on Shinkansen platforms at Station 'A' using Computational Fluid Dynamics (CFD). We focused on the factors that influence the temperature dynamics associated with heat generated by trains and station buildings and their effect on the ambient temperature on platforms. In the case of heat generated by trains, air temperature on Shinkansen platforms increased by 4 to 7 degrees compared to when trains generated no heat. When a 50-m high station building was located on the windward side of the platforms, air temperature on Platform X was 2 degrees higher than when the station buildings were absent. Air? temperature on platforms VII to IX increased progressively, and the maximum air temperature on platform VIII was 3 K higher than if station buildings were absent.

The positioning accuracy of the Global Positioning System (GPS) has been improved considerably during the past two decades. The main error sources such as ionospheric refraction, orbital uncertainty, antenna phase center variation, signal multipath, and tropospheric delay have been reduced substantially, if not eliminated. In this study, the GPS data collected by the GPS receivers that were established as continuously operating reference stations by International GNSS Service (IGS), Ministry of the Interior (MOl), Central Weather Bureau (CWB), and Industrial Technology Research Institute (ITRI) Of Taiwan are utilized to investigate the impact of atmospheric water vapor on GPS positioning determination. The surface meteorological measurements that were concurrently acquired by instruments co-located with the GPS receivers include temperature, pressure and humidity data. To obtain the influence of the GPS height on the proposed impact study. A hydrodynamic ocean tide model (GOTOO.2 model) and solid earth tide were used to improve the GPS height. The surface meteorological data (pressure, temperature and humidity) were introduced to the data processing with 24 troposphere parameters. The results from the studies associated with different GPS height were compared for the cases with and without a priori knowledge of surface meteorological measurements. The finding based on the measurements in 2003 is that the surface meteorological measurements have an impact on the GPS height. The associated daily maximum of the differences is 1.07 cm for the KDNM station. The impact is reduced due to smoothing when the average of the GPS height for the whole year is considered.

Satellite cameras are calibrated before launch in detail and in general, but it cannot be guaranteed that the geometry is not changing during launch and caused by thermal influence of the sun in the orbit. Modem satellite imaging systems are based on CCD-line sensors. Because of the required high sampling rate the length of used CCD-lines is limited. For reaching a sufficient swath width, some CCD-lines are combined to a longer virtual CCD-line. The images generated by the individual CCD-lines do overlap slightly and so they can be shifted in x- and y-direction in relation to a chosen reference image just based on tie points. For the alignment and difference in scale, control points are required. The resulting virtual image has only negligible errors in areas with very large difference in height caused by the difference in the location of the projection centers. Color images can be related to the joint panchromatic scenes just based on tie points. Pan-sharpened images may show only small color shifts in very mountainous areas and for moving objects. The direct sensor orientation has to be calibrated based on control points. Discrepancies in horizontal shift can only be separated from attitude discrepancies with a good three-dimensional control point distribution. For such a calibration a program based on geometric reconstruction of the sensor orientation is required. The approximations by 3D-affine transformation or direct linear transformation (DL n cannot be used. These methods do have also disadvantages for standard sensor orientation. The image orientation by geometric reconstruction can be improved by self calibration with additional parameters for the analysis and compensation of remaining systematic effects for example caused by a not linear CCD-line. The determined sensor geometry can be used for the generation? of rational polynomial coefficients, describing the sensor geometry by relations of polynomials of the ground coordinates X, Y and Z.

Because forest fire changes the direction according to the environmental elements, it is difficult to predict the direction of it. Currently, though some researchers have been studied to which predict the forest fire occurrence and the direction of it, using the remote detection technique, it is not enough and efficient. And recently because of the development of the sensor technique, a lot of In-Situ sensors are being developed. These kinds of In-Situ sensor data are used to collect the environmental elements such as temperature, humidity, and the velocity of the wind. Accordingly we need the prediction technique about the environmental elements analysis and the direction of the forest fire, using the In-Situ sensor data. In this paper, as a technique for predicting the direction of the forest fire, we propose the correlation analysis technique about In-Situ sensor data such as temperature, humidity, the velocity of the wind. The proposed technique is based on the clustering method and clusters the In-Situ sensor data. And then it analyzes the correlation of the multivariate correlations among clusters. These kinds of prediction information not only helps to predict the direction of the forest fire, but also finds the solution after predicting the environmental elements of the forest fire. Accordingly, this technique is expected to reduce the damage by the forest fire which occurs frequently these days.

Desertification is one of the main global environmental phenomena. It has resulted in deterioration environment and poor economy, and imposed threat to the surviving environment of the overall mankind. Therefore, creating of methods for monitoring and estimate of risk desertification are necessary. Early warning system is one of important ways for monitoring and forecasting of desertification. Remote Sensing and GIS technology are as suitable tools and methods for early warning system. In this aim, we have evaluated of applications of remote sensing and GIS in monitoring and estimating desertification process (case study in Fars Province of Iran). In this research, we have considered erosion and vegetation cover parameters as main factors affecting in desertification process. The result shows that remote sensing and GIS technology could be useful in evaluation of desertification as one method for desertification early warning. Also, Results suggested that erosion and plant cover are affecting in develop the desertification process in study area.

As global warming proceeds, South Eastern Asia is undergoing drought, and the harshness of drought in the middle area of Korea is increasing. Especially, there has been the worst spring drought in 2001 since the first meteorological observation, and the damages caused by that drought are being ana lysed in various ways. In this study, spectral indices derived from satellites are used to examine 2001 spring drought, and the application of MODIS Data products as the quantitative tool to analyse drought in the future is examined.

Super resolution image reconstruction method refers to image processing algorithms that produce a high resolution(HR) image from observed several low resolution(LR) images of the same scene. This method is proved to be useful in many practical cases where multiple frames of the same scene can be obtained, such as satellite imaging, video surveillance, video enhancement and restoration, digital mosaicking, and medical imaging. In this paper we applied super resolution reconstruction method in spatial domain to video sequences. Test images are adjacently sampled images from continuous video sequences and overlapped for high rate. We constructed the observation model between the HR images and LR images applied by the Maximum A Posteriori(MAP) reconstruction method that is one of the major methods in the super resolution grid construction. Based on this method, we reconstructed high resolution images from low resolution images and compared the results with those from other known interpolation methods.

Recently, the generation of panoramic images and high quality mosaic images from video sequences has been attempted by a variety of investigations. Among a matter of investigation, in this paper, left and right stereo mosaic image generation utilizing airborne-video sequence images is focused upon. The stereo mosaic image is generated by creating left and right mosaic image which is generated by front and rear slit having different viewing angle in consecutive video frame images. The generation of stereo mosaic image proposed in this paper consists of several processes: camera parameter estimation for each video frame image, rectification, slicing, motion parallax elimination and image mosaicking. However it is necessary to check the feasibility on generating stereo mosaic image as explained processes. Therefore, in this paper, we performed the feasibility test on generating stereo mosaic image using video frame images. In doing so, anaglyphic image for stereo mosaic images is generated and tested for feasibility check.

This research is aimed at the development of a software that predicts the surface temperature profiles of three-dimensional objects on the ground considering the spectral solar radiation through the atmosphere. The thermal modelling is essential for identifying the objects on the scenes obtained from the satellites. And the temperature distribution on the objects is necessary to obtain their infrared images in contrast to the background. We developed a software that could be used to model the thermal problems of the ground objects irradiated by the spectral solar radiation. This software can be used to handle the conduction within the object as a one-dimensional mode into the depth or as a three-dimensional mode through the media. LOWTRAN7 is used to model the spectral solar radiation including the direct and diffuse solar radiances. In this paper, temperature distributions on the objects obtained by using the one-dimensional and the three-dimensional thermal models are compared with each other to examine the applicability of the relatively easy-to-apply one-dimensional model.

Hyperspectral data consists of more than 200 spectral bands that are highly correlated. In order to utilize hyperspectral data for classification, dimensional reduction or feature extraction is desired. By applying feature extraction, computational complexity of classification can be reduced and classification accuracy may be improved. In this paper, a genetic algorithm based feature extraction technique is proposed. Measure from discriminant analysis is utilized as optimization criterion. A subset of spectral bands is selected by genetic algorithm. Dimension of feature space is further reduced by linear transformation. Feasibility of the proposed technique is evaluated with AVIRIS data.

A novel hyperspectral imaging spectrometer controlling spatial and spectral resolution individually has been proposed. This imaging spectrometer uses a zoom lens as a telescope and a focusing element. It can change the spatial resolution fixing the spectral resolution or the spectral resolution fixing the spatial resolution. Here, we report the concept of the hyperspectral imaging spectrometer with the novel zooming function and the optical design of a zoom lens as the focusing element. By using lens module and third-order aberration theory, we have presented the initial design of four-group zoom lens with external entrance pupil. And the optimized zoom lens with a focal length of 50 to 150 mm is obtained from the initial design by the optical design software. As a result, the designed zoom lens shows satisfactory performances in wavelength range of 450 to 900 nm as a focusing element in an imaging spectrometer. Furthermore, the collimator lens of the imaging spectrometer is designed through the third-order aberration correction by using an iterative process.

Currently, a number of control points are required in order to achieve accurate geolocation of satellite images. Control points can be generated from existing maps or surveying, or, preferably, from GPS measurements. The requirement of control points increase the cost of satellite mapping, let alone it makes the mapping over inaccessible areas troublesome. This paper investigates the possibilities of modeling an entire imaging strip with control points obtained from a small portion of the strip. We tested physical sensor models that were based on satellite orbit and attitude angles. It was anticipated that orbit modeling needed a sensor model with good accuracy of exterior orientation estimation, rather then the accuracy of bundle adjustment. We implemented sensor models with various parameter sets and checked their accuracy when applied to the scenes on the same orbital strip together with the bundle adjustment accuracy and the accuracy of estimated exterior orientation parameters. Results showed that although the models with good bundle adjustments accuracy did not always good orbit modeling and that the models with simple unknowns could be used for orbit modeling.

Hyperspectral image data have great potential to depict more detailed information on biophysical characteristics of surface materials, which are not usually available with multispectral data. This study aims to test the potential of hyperspectral data for classifying five soil classes defined by the vector product interim terrain data (VITD). In this study, we try to classify surface materials of bare soil over the study area in Korea using both hyperspectral and multispectral image data. Training and test samples for classification are selected with using VITD vector map. The spectral angle mapper (SAM) method is applied to the EO-I Hyperion data and Landsat ETM+ data, that has been radiometrically corrected and geo-rectified. Higher classification accuracy is obtained with the hyperspectral data for classifying five soil classes of gravel, evaporites, inorganic silt and sand.

Telescope structure based on Korsch type optical layout was suggested for a large aperture optical system. Korsch type optical layout is regarded as providing wide field of view and no color aberration for which high resolution space cameras greatly demand. For the suggested Korsch type telescope structure, two folding mirrors are adopted, firstly to provide for the refocusing device mounting plane on the second fold mirror assembly, secondly by double folding the light path to concisely confine focal plane assembly within the perimeter of the tube. Optical layput design and corresponding support structure design were attained.

This paper presents a preliminary analysis result on SAR-related journal papers published since 1960s. Abstracts of more than 2700 peer-reviewed English journal papers were collected and classified into various categories according to their systems, techniques, and application fields. Statistics on each category were provided so that one can understand historical and on-going development in SAR systems, techniques, and a variety of application fields such as land, ocean, cryosphere and atmosphere. This statistical data would be an essential guideline to establish a future SAR system application and satellite manoeuvring policy.

This paper presents an unsupervised change detection methodology designed for the detection of landslide areas. The proposed methodology consists of two analytical steps: one for multi-temporal segmentation and the other for automatic selection of thresholding values. By considering the conditions of landslide occurrences and the spectral behavior of multi-temporal remote sensing images, some specific procedures are included in the analytical steps mentioned above. The effectiveness and applicability of the methodology proposed here were illustrated by a case study of the Gangneung area, Korea. The case study demonstrated that the proposed methodology could detect about $83\%$ of landslide occurrences.

Calibration and Validation are major element of any space borne Earth Observation Mission. These activities are the major objective of the commissioning phases but routine activities shall be maintained during the whole mission in order to maintain the quality of the product delivered to the users or at least to fully characterise the evolution with time of the product quality. With the launch of ERS-l in 1991, the European Space Agency decided to put in place a group dedicated to these activities, along with the daily monitoring of the product quality for anomaly detection and algorithm evolution. These four elements are all strongly linked together. Today this group is fully responsible for the monitoring of two ESA missions, ERS-2 and Envisat, for a total of 12 instruments of various types, preparing itself for the Earth Explorer series of five. other satellites (Cryosat, Goce, SMOS, ADM-Aeolus, Swarm) and at various levels in past and future Third Party Missions such as Landsat, J-ERS, ALOS and KOMPSAT. The Joint proposal by the European Union and the European Space Agency for a 'Global Monitoring for Environment and Security' project (GMES), triggers a review of the scope of these activities in a much wider framework than the handling of single missions with specific tools, methods and activities. Because of the global objective of this proposal, it is necessary to put in place Multi-Mission Calibration and Validation systems and procedures. GMES Calibration and Validation activities will rely on multi source data access, interoperability, long-term data preservation, and definition standards to facilitate the above objectives. The scope of this presentation is to give an overview of the current Calibration and Validation activities at ESA, and the planned evolution in the context of GMES.

Many building detection methods mainly rely on line segments extracted from aerial or satellite imagery. Building detection methods based on line segments, however, are difficult to succeed in high resolution satellite imagery such as IKONOS imagery, for most buildings in IKONOS imagery have small size of roofs with low contrast between roof and background. In this paper, we propose an efficient method to extract line segments and group them at the same time. First, edge preserving filtering is applied to the imagery to remove the noise. Second, we segment the imagery by watershed method, which collects the pixels with similar intensities to obtain homogeneous region. The boundaries of homogeneous region are not completely coincident with roof boundaries due to low contrast in the vicinity of the roof boundaries. Finally, to resolve this problem, we set up snake model with segmented region boundaries as initial snake's positions. We used a greedy algorithm to fit a snake to roof boundary. Experimental results show our method can obtain more .correct roof boundary with small size and low contrast from IKONOS imagery. Snake algorithm, building roof detection, watershed segmentation, edge-preserving filtering

This paper addresses the use of directional textural information for connecting road segments. In urban scene, some roads are occluded by buildings, casting shadow of buildings, trees, and cars on streets. Automatic extraction of road network from remotely sensed high resolution imagery is generally hindered by them. The results of automatic road network extraction will be incomplete. To overcome this problem, several perceptual grouping algorithms are often used based on similarity, proximity, continuation, and symmetry. Roads have directions and are connected to adjacent roads with certain angles. The directional information is used to guide road fragments connection based on roads directional inertia or characteristics of road junctions. In the primitive stage, roads are extracted with textural and direction information automatically with certain length of linearity. The primitive road fragments are connected based on the directional information to improve the road network. Experimental results show some contribution of this approach for completing road network, specifically in urban area.

Microphytobenthos bloom from late January to early March in Korean tidal flats. KOMPSAT-2 will provide multi-spectral images with a spatial resolution of 4 m comparable with IKONOS. Using IKONOS and Landsat data, algal mat detection was tested in the Saemangeum area~ Micro-benthic diatoms are abundant and a major primary product in the tidal flats. A linear spectral unmixing (LSU) method was applied to the test data. LSU was effective to detect algal mat and the classified algal mat fraction well correlated with NDVI image. Fine grained upper tidal flats are generally known to be the best environment for algal mat. Algal mat thriving in coarse grained lower tidal flats as well as upper tidal flats were reported in this study. A high resolution multi-spectral sensor in KOMPSAT-2 will provide useful data for long-term monitoring of microphytobenthos in tidal flats.

The use of satellite remote sensing in maritime safety and security can aid in the detection of illegal fishing activities and provide more efficient use of limited aircraft or patrol craft resources. In the area of vessel traffic monitoring for commercial vessels, Vessel Traffic Service (VTS) which use the ground-based radar system have some difficulties in detecting moving ships due to the limited detection range. A virtual vessel traffic control system is introduced to contribute to prevent a marine accident such as collision and stranding from happening. Existing VTS has its limit. The virtual vessel traffic control system consists of both data acquisition by satellite remote sensing and a simulation of traffic environment stress based on the satellite data, remotely sensed data. And it could be used to provide timely and detailed information about the marine safety, including the location, speed and direction of ships, and help us operate vessels safely and efficiently. If environmental stress values are simulated for the ship information derived from satellite data, proper actions can be taken to prevent accidents. Since optical sensor has a high spatial resolution, JERS satellite data are used to track ships and extract their information. We present an algorithm of automatic identification of ship size and velocity. This paper lastly introduce the field testing results of ship detection by RADARSAT SAR imagery, and propose a new approach for a Vessel Monitoring System(VMS), including VTS, and SAR combination service.

A crop management system was developed using Visual Basic and ArcGIS VBA. The system is operated on ArcGlS 8.3 with Microsoft Access MOB. Landsat +ETM, KOMPSAT-l EOC, ASTER VNIR and IKONOS panchromatic (pan) and multi-spectral (MIS) images were included in the system to understand what kind of agriculture-related information can be extracted for each images. Agriculture related data inventories using crop cover information such as texture and average pixel value of the crop based on cultivation calendar were designed ,and implemented. Three IKONOS images (May 25,2001, December 25,2001, October 23,2003) were loaded in the system to show crop cover characteristics such as rice, pear, grape, red pepper, garlic, and surface water cover of reservoir with field surveys. GIS layers such as DEM (Digital Elevation Model), stream, road, soil, land use and administration boundary were also supplied and can be overlaid with images to enhance the understanding the general agricultural characteristics and identifying the location easily.

This study was carried out to investigate the effects of spatial resolutions on digital image for detecting pine trees damaged by pine wilt disease. Color infrared images taken from PKNU-3 multispectral airborne photographing system with a spatial resolution of 50cm was used as a basic data. Further test images with spatial resolutions of 1m, 2m and 4m were made from the basic data to test the detecting capacity on each spatial resolution. The test was performed with visual interpretation both on mono and stereo modus and compared with field surveying data. It can be conclude that it needs less than 1m spational resolutions or 1m spatial resolutions with stereo pair in order to detect pine trees damaged by pine wilt disease.

COMS (Communication, Ocean, and Meteorological Satellite) will be launch at end of year 2008. For speedy and security communication of COMS, KARl (Korea Aerospace Research Institute) decided encryption and compression design. Encryption design is based on DES (Data Encryption Standard), so that encryption key generation and management are important issues in COMS operation. And Compression is based on loss and lossless JPEG (Joint Photographic Export Group) standard. JPEG is one of generally using compression algorithm in image.

COMS (Communication, Ocean, and Meteorological Satellite) will be launch at end of year 2008. For receiving of COMS LRlT, KARl (Korea Aerospace Research Institute) finished design and software realization of COMS SDUS (Small Data Utilization System). SDUS is a small station receiving LRlT data for distribute satellite image, weather information, and so on. For the future project, KARl preparing COMS MDUS (Mass Data Utilization System) that can receiving large size of data over than 2M BPS (Bit Per Seconds) data size.

The digital map expresses natural topographies and artificial things with 3D position coordinates in the computer such as the road, railway, building, river, mountain, paddy and dryland. Therefore, the digital map is regarded as an important factor in the information-oriented society. However, it is difficult to maintain the most recent topographic information all the times because of restricted budget and time. For that, the efficient method corresponded with the digital map should be presented. This study aims to suggest the way to make an estimate of updating cost for 1:5,000 scale digital map by using remotely sensed data. To predict updating area of the digital map, the screen digitizing method was applied to the overlapped images and digital maps.

As the Ubiquitous generation approaches, the importance of the sensor data processing is growing. The data approximation scheme, one of the data processing methods, can be the key of sensor data processing, for it is related not only to the lifetime of sensors but also to the size of the storage. In this paper, we propose the Harmonic Wavelet transform which can minimize the relative error for given sensor data. Harmonic Wavelets use the harmonic mean as a representative which is the minimum point of the maximum relative error between two data values. In addition, Harmonic Wavelets retain the relative errors as wavelet coefficients so we can select proper wavelet coefficients that reduce the relative error more easily. We also adapt the greedy algorithm for local optimization to reduce the time complexity. Experimental results show the performance and the scalability of Harmonic Wavelets for sensor data.

A ribonucleic acid (RNA) is one of the two types of nucleic acids found in living organisms. An RNA molecule represents a long chain of monomers called nucleotides. The sequence of nucleotides of an RNA molecule constitutes its primary structure, and the pattern of pairing between nucleotides determines the secondary structure of an RNA. Non-coding RNA genes produce transcripts that exert their function without ever producing proteins. Predicting the secondary structure of non-coding RNAs is very important for understanding their functions. We focus on Nussinov's algorithm as useful techniques for predicting RNA secondary structures. We introduce a new traceback matrix and scoring table to improve above algorithm. And the improved algorithm provides better levels of performance than the originals.

To account for the importance of variable in multi-sensor data fusion, random forests are applied to supervised land-cover classification. The random forests approach is a non-parametric ensemble classifier based on CART-like trees. Its distinguished feature is that the importance of variable can be estimated by randomly permuting the variable of interest in all the out-of-bag samples for each classifier. Supervised classification with a multi-sensor remote sensing data set including optical and polarimetric SAR data was carried out to illustrate the applicability of random forests. From the experimental result, the random forests approach could extract important variables or bands for land-cover discrimination and showed good performance, as compared with other non-parametric data fusion algorithms.

Recently, in Korea, recognizing the importance of satellite imagery and a national project, the development of satellite providing satellite imagery information of 1m high resolution has been carried out. As the application of satellite. imagery information is expanded to the national land, the environment and geographical information, etc, the necessity of integrated management of satellite imagery information increases. Unfortunately, in case of Korea, currently, the results that institutes for satellite imagery processing produce with satellite imagery have been individually managed. Integrated Management of Satellite Imagery Information project which is being promoted by ETRI (Electronics and Telecommunication Research Institute) in Korea will provide the solutions for the above mentioned problems. In this research work, we designed standard metadata for integrated management of satellite imagery information in consideration of international and national standard.

This paper proposes and evaluates a new approach to detect ships as targets from Radarslit-l SAR (Synthetic Aperture Radar) imagery in the vicinity of Korean peninsula. To be more specific, a labeling technique and morphological filtering in conjunction with some other methods are employed to automatically detect the ships. From the test, the ships are revealed to be detected. For ground truth data, information from a radar system is used, which allows assessing accuracy of the approach. The results showed that the proposed approach has the high potential in automatically detecting the ships

Time series are comprehensively appeared and developed in many applications, ranging from science and technology to business and entertainrilent. Similarity search under time warping has attracted much interest between the time series in the large sequence databases. DTW (Dynamic Time Warping) is a robust distance measure and is superior to Euclidean distance for time series, allowing similarity matching although one of the sequences can elastic shift along the time axis. Nevertheless, it is more unfortunate that DTW has a quadratic time. Simultaneously the false dismissals are come forth since DTW distance does not satisfy the triangular inequality. In this paper, we propose an efficient range query algorithmbased on a new similarity search method under time warping. When our range query applies for this method, it can remove the significant non-qualify time series as early as possible before computing the accuracy DTW distance. Hence, it speeds up the calculation time and reduces the number of scanning the time series. Guaranteeing no false dismissals, the lower bounding function is advised that consistently underestimate the DTW distance and satisfy the triangular inequality. Through the experimental result, our range query algorithm outperforms the existing others.

Satellite payload on-board date compression unit are use for saving date storage space and reducing time to transmit payload data to the ground station. The KOMPSAT-3 payload will generate higher data rate than KOMPSAT-2 due to its better ground sample distance capacity. High input data rate and limited output transmission data rate might lead excessive compression and degraded image quality. This paper presents a trade-off study about data storage capacity and compression parameters for estimated KOMPSAT-3 system.

For detecting an intrusion based on the anomaly of a user's activities, previous works are concentrated on statistical techniques or frequent episode mining in order to analyze an audit data. But, since they mainly analyze the average behaviour of user's activities, some anomalies can be detected inaccurately. Therefore, we propose an anomaly detection method that utilizes an associative classification for modelling intrusion detection. Finally, we proof that a prediction model built from associative classification method yields better accuracy than a prediction model built from a traditional methods by experimental results.

The COMS, Korea's first geostationary multipurpose satellite program will accommodate 3 kind of payloads; Ka-Band communication transponder, GOCI (Geostationary Ocean Color Imager), and MI (Meteorological Imager). MI raw data will be transferred to ground station via L-band link. The ground station will perform image data processing for raw data, generate them into the LRIT/HRIT format, the user dissemination data recommended by the CGMS. The LRIT/HRIT are disseminated via satellite to user stations. This paper shows the COMS LRIT data generation procedure based on COMS LRIT specification and its verification results using the LRIT user station.

The need for LBS (Loc,ation Based Services) is increasing due to the wnespread of mobile computing devices and positioning technologies~ In LBS, there are many applications that need to manage moving objects (e.g. taxies, persons). The moving object join operation is to make pairs with spatio-temporal attribute for two sets in the moving object database system. It is import and complicated operation. And processing time increases by geometric progression with numbers of moving objects. Therefore efficient methods of spatio-temporal join is essential to moving object database system. In this paper, we apply spatial join methods to moving objects join. We propose two kind of join methods with TB- Tree that preserves trajectories of moving objects. One is depth first traversal spatio-temporaljoin and another is breadth-first traversal spatio-temporal join. We show results of performance test with sample data sets which are created by moving object ,generator tool.

New renewable energy information becomes one of the greatest issues all over the world because of serious environment problems and limited fossil resources. The new renewable energy source information system is treated seriously for efficient management and distribution as dealing with these energy problems. However, it is difficult to manage and utilize new renewable energy information because gathering and surveying information is progressed individually in each research field. Therefore this paper will establish ISP(Information strategy Planning) and propose the basic management system based-on GIS to analyze new renewable energy such as solar energy, wind power, small hydro, biomass, geothermal etc. and build the integration management system. The proposed integration management system can provide spatial analysis using thematic map, data search, data import/export and interpolation about users quenes.

The LBS (Location-Based Services) are valuable information services combined the location of moving object with various contents such as map, POI (point of Interest), route and so on. The must general service of LBS is route determination service and its applicable parts are FMS (Fleet Management System), travel advisory system and mobile navigation system. The core function of route determination service is determination of optimal route from source to destination in various environments. The MODB (Moving Object Database) system, core part of LBS composition systems, is able to manage current or past location information of moving object and massive trajectory information stored in MODB is value-added data in CRM, ERP and data mining part. Also this past trajectory information can be helpful to determine optimal route. In this paper, we suggest methods to determine optimal route by querying past trajectory information in MODB system and verify the effectiveness of suggested method.

In these days, the management and visualization of 3D geo-spatial information is regarded as one of an important issue in GiS and remote sensing fields. 3D GIS is considered with the database issues such as handling and managing of 3D geometry/topology attributes, whereas 3D visualization is basically concerned with 3D computer graphics. This study focused on the design and implementation for the OpenGL API-based rendering system for the complex types of 3D geo-spatial features. In this approach 3D features can be separately processed with the functions of authoring and manipulation of terrain segments, building segments, road segments, and other geo-based things with texture mapping. Using this implementation, it is possible to the generation of an integrated scene with these complex types of 3D features. This integrated rendering system based on the feature-based 3D-GIS model can be extended and effectively applied to urban environment analysis, 3D virtual simulation and fly-by navigation in urban planning. Furthermore, we expect that 3D-GIS visualization application based on OpenGL API can be easily extended into a real-time mobile 3D-GIS system, soon after the release of OpenGLIES which stands for OpenGL for embedded system, though this topic is beyond the scope of this implementation.

To estimate presumptive local ground subsidence area near Abandoned Under ground Coal Mine(AUCM) at Samcheok city in Korea, the geological properties of existing ground subsidence area and the geophysical prospecting data were analyzed using GIS. The electrical resistivity survey and seismic reflection survey database were constructed from investigation reports and factors which are related with ground subsidence such as geological map, topological map, land use map, lineament map, groundwater level, RMR (Rock Mass Rating), mining tunnel map and slope database were constructed also to make a comparative study of each parameters. As a result of the spatial analysis of existing ground subsidence area, 9 major factors causing ground subsidence were extracted and a connection between the structure of underground and the ground subsidence was determined from the analysis of geophysical prospecting data. The estimation of presumptive ground subsidence area was performed using the correlation between the result from neural network analysis of 9 factors and the scrutiny of geophysical prospecting data.

In order to provide the reliable service and contents to telematics service user, any service server must be tested and verified before launching its service in sufficient. In this paper, we proposed a test framework for telematics server. The proposed framework includes conformance test of server, interoperability test between telematics service server and telematics terminal. The framework proposed the concept and test model for two categories of testing.

The advance of wireless telecommunication and observation technologies leads developing sensor and sensor network for serving the context information continuously. Besides, in order to understand and cope with the context awareness based on the sensor network, it is becoming important issue to deal with plentiful data transmitted from various sensors. Therefore, we propose a context awareness system to deal with the plentiful sensor data in a vast area such as the prevention of a forest fire, the warning system for detecting environmental pollution, and the analysis of the traffic information, etc. The proposed system consists of the context acquisition to collect and store various sensor data, the knowledge base to keep context information and context log, the rule manager to process context information depending on user defined rules, and the situation information manager to analysis and recognize the context, etc. The proposed system is implemented for managing renewable energy data management transmitted from a large scale area.

Context-awareness techniques in ubiquitous computing environment provide various services to users who need to get information via the analysis of collected information from sensors in a spatial area. Context-awareness has been increased in ubiquitous computing and is applied to many different applications such as disaster management system, intelligent robot system, transportation management system, shopping management system, and digital home service. Many researches have recently focused on services that provide the appropriate information, which are collected from Internet by different kinds of sensors, to users according to context of their surrounding environment. In this paper, we propose an abstraction model to manage the large-scale contextual information and their metadata which are collected from different kinds of in-situ sensors in a spatial area and are presented them on the web. This model is composed of the modules expressing functional elements of sensors using sensorML(Sensor Model Language) based on XML language and the modules managing contextual information, which is transmitted from the sensors.

Mobile IPv6(MIPv6) allows a Mobile Node to talk directly to its peers while retaining the ability to move around and change the currently used IP address. One of the major issues regarding the basic Mobile IPv6 protocol is related to the handover management of a mobile node. This paper proposes efficient approach for adaptation of MIPv6 sing context information in roaming environments. To investigate on a efficient and secure handover procedure, proposed approach method will give us the following advantages: (l)the intention of context is to reduce latency, packet losses and avoid re-initiation of signaling to and from mobile nodes,(2) FMIPv6 aims to reduce handover latency due to IP protocol operations as small as possible in comparison to the inevitable link switching latency.

Because the current web search engine estimates the similarity of documents, using the frequency of words, many documents irrespective of the user query are provided. To solve these kinds of problems, the semantic web is appearing as a future web. It is possible to provide the service based on the semantic web through ontology which specifies the knowledge in a special domain and defines the concepts of knowledge and the relationships between concepts. In this paper to search the information of potential customers for home-delivery marketing, we model the specific domain for generating the ontology. And we research how to retrieve the information, using the ontology. Therefore, in this paper, we generate the ontology to define the domain about potential customers and develop the search robot which collects the information of customers.

The telematics positioning testbed is an infrastructure to test and verify positioning technology, the sub-component of telernatics system. The positioning testbed provides the environment of performance analysis for acquisition of static and dynamic positioning information using telematics vehicle. This testbed consists of onboard positioning system, positioning reference station and lab positioning server. The onboard positioning system equipped in telematics vehicle, consists of target positioning system, reference positioning system, and analysis tool. A equipment acquiring high precision positioning data obtained from GPS combined with IMU was set as a reference positioning system. Analysis tool compares observed positioning data with high precision positioning information from a reference positioning system, and processes positioning information. Positioning reference station is RTK system used for reducing atmosphere error, and it transmits corrected information to reference positioning system. Positioning server which is located at laboratory manages positioning database and provides monitoring data to integrated testbed operating system. It is expected that the testbed supports commercialization of telernatics technology and services, integrated testing among component technology and verification.

In Taiwan, there are more the one hundred GPS tracking stations maintained by Ministry of the Interior (MOI), Academia Sinica, Central Weather Bureau and Central Geological Survey. In the further, they may be instead of the GPS controlling points after giving the lawful status. In other words, the engineers don't need to survey on the reference points when they are surveying in the field. They only need to download the GPS data via internet and process the observations in their company. The precise coordinates of the unknown points will be obtained. Therefore, the data qualities of the tracking stations are more and more important. In this study, six data quality indexes were adopted as follows: observations, cycle slips, multipath on L1, multipath on L2, clock offset and frequency stability. Besides, the relationships of the indexes and the positioning precision were found. The frequency stability of GPS receiver is the most important index, the cycle slip is the second index and the mutlipath is the third index. According to the results, the auto-analytical system of GPS data quality was established and the tracking stations were monitored. When the receiver got some problem or the station's environment changed, we hope to find and resolve the problems earlier to make sure the high data quality of the tracking stations. Moreover, we try to design a data quality verification to help users and let the engineers have more and more confidence when they use the data of GPS tracking stations.

Soil loss is widely recognized as a threat to farm livelihoods and ecosystem integrity worldwide. Soil loss prediction models can help address long-range land management planning under natural and agricultural conditions. Even though it is hard to find a model that considers all forms of erosion, some models were developed specifically to aid conservation planners in identifying areas where introducing soil conservation measures will have the most impact on reducing soil loss. Revised Universal Soil Loss Equation (RUSLE) computes the average annual erosion expected on hillslopes by multiplying several factors together: rainfall erosivity (R), soil erodibility (K), slope length and steepness (LS), cover management (C), and support practice (P). The value of these factors is determined from field and laboratory experiments. This study calculated soil erosion using GIS-based RUSLE model in Imha basin and examined soil erosion source area using SPOT 5 high-resolution satellite image and land cover map. As a result of analysis, dry field showed high-density soil erosion area and we could easily investigate source area using satellite image. Also we could examine the suitability of soil erosion area applying field survey method in common areas (dry field & orchard area) that are difficult to confirm soil erosion source area using satellite image.

The use of remotely sensed data and geographic information system (GIS) to develop conservation-oriented watershed management strategies on Imha Dam, Korea, is presented. The change of land use for study area was analyzed using multi-temporal Landsat imagery. A soil loss model was executed within a GIS environment to evaluate watershed management strategies in terms of soil loss. In general, remotely sensed data provide efficient means of generating the input data required for the soil loss model. Also, GIS allowed for easy assessment of the relative erosion hazard over the watershed under the different land use change options. The soil loss model predicted substantial declines in soil loss under conservation-oriented land management compared to current land management for Imha Dam. The results of this study indicate that soil loss potential (5,782,829 ton/yr) on Imha Dam in 2003 is approximately 1.27 times higher than that (4,557,151 ton/yr) in 1989. This study represents the first attempt in the application of GIS technology to watershed conservation planning for Imha Dam. The procedures developed will contribute to the evolution of a decision support system to guide the land planning and dam management in Imha Dam.

A persistent maximum over the southern tropical Atlantic in the latitudinal tropospheric ozone distribution from the CCD method is seen in the latitudinal tropospheric ozone distribution from the TOMS-Pacific method. The tropical Atlantic paradox exists in the results of both the CCD and TOMS-Pacific methods. During the northern burning season, the latitudinal distributions in the tropospheric ozone derived from the TOMS-SAGE and TOMS-Sonde methods show higher tropospheric ozone over the northern tropical Atlantic than the southern Atlantic due to a stronger gradient in stratospheric ozone relative to that from the CCD and TOMS-Pacific methods.

We have developed Hybrid algorithm for yellow sand detection. Hybrid algorithm is composed of three methods using infrared bands. The first method used the differential absorption in brightness temperature difference between $11\mu m\;and\;12\mu m$ (BID _1), through which help distinguish the yellow sand from various meteorological clouds. The second method uses the brightness temperature difference between $3.7\mu m\;and\;11\mu m$ (BID_2). The technique would be most sensitive to dust loading during the day when the BID _2 is enhanced by reflection of $3.7\mu m$ solar radiation. The third one is a newly developed algorithm from our research, the so-called surface temperature variation method (STY). We have applied the three methods to MODIS for derivation of the yellow sand dust and in conjunction with the Principle Component Analysis (PCA), a form of eigenvector statistical analysis. PCI shows better results for yellow sand detection in comparison with the results from individual method. The comparison between PCI and MODIS aerosols optical depth (AOD) shows remarkable good correlations during daytime and relatively good correlations over the land.

The distribution and changes of tropospheric nitrogen dioxide ($NO_2$) are analyzed using the satellite measurements data from GOME (Global Ozone Monitoring Experiment) and SCIMACHY (SCanning Imaging Absorption spectroMeter for Atmospheric CHartographY). We produced global maps of tropospheric $NO_2$ for 4 seasons using GOME measurements from January 1997 to June 2003. The global distribution shows high values in regions with dense population and high industrialization. Tropospheric $NO_2$ shows obvious seasonal changes depending on its emission and lifetime. Based on the good agreement between two instruments in the time period of overlapping measurements (January 2003-June2003), we linked SClAMACHY data to the GOME time series. The combined time series over the past decade indicate that $NO_2$ 1evels over China are rapidly increasing while those over Europe are decreasing. We also discussed potential application of spaceborne instruments in detecting and characterizing long-distance transport of $NO_2$.

Remote sensing of atmospheric aerosol using MODIS satellite data has been proven to be very useful in global/regional scale aerosol monitoring. Due to their large spatial resolution of $10km^2$ MODIS aerosol optical thickness (AOT) data have limitations for local/urban scale aerosol monitoring applications. Modified Bremen Aerosol Retrieval (BAER) algorithm developed by von Hoyningen-Huene et al. (2003) and Lee et al. (2005) has been applied in this study to retrieve AOT in fe resolutions of $500m^2$ over Korea. Look up tables (LUTs) were constructed from the aerosol properties based on sun-photometer observation and radiation transfer model calculations. It was found that relative error between the satellite products and the ground observations was within about $15\%$. Resulting AOT products were correlated with surface PMIO concentration data. There was good correlation between MODIS AOT and surface PM concentration under certain atmospheric conditions, which supports the feasibility of using the high-resolution MODIS AOT for local and urban scale air quality monitoring

We have applied the TOMS aerosols retrieval algorithm to GLI measurements. TOMS has utilized the aerosol index, which is a measure of the change in spectral contrast due to the wavelength-dependent effects of aerosols. We have retrieved the GLI aerosol index, which is made by the pair of 380/400nm, 380/412nm, 380/460nm, and 412/460nm. We have found that the biomass burning aerosols represent the absorbing aerosols. In addition, the pair of 380/460nm has shown the best signal for detecting aerosols in Principal Component Analysis(PCA) and comparison of aerosol optical thickness from AERONET data. The theoretical aerosol index is also shown the best signal in the pair of 380/460nm.

Polarimetric measurements of the sky radiation by the PSR-I000, which is the multi-spectral polarimeter developed by the Opt Research Corporation and has the same wavelength regions (443nm, 490nm, 565nm, 670nm, 765nm and 865nm) as the ADEOSII/POLDER sensor, have been carried out at the ground station in Kanazawa city, Japan from March to May. First of all, the wavelength dependency of degrees of polarization is examined and it is shown that degrees of polarization measured under the hazy dust cloud are lower than those measured in the clear sky and decrease as the wavelength increases. Next, a new method for estimating optical properties, such as the optical thickness, the number size distribution and the refractive index, of the Asian dust and the ground reflectance from degrees of polarization measured by PSR-I000 is described. Finally, this method is applied to polarization data acquired on April 15,2002. As a result, it is shown that our estimation algorithm provides a good result.

The characteristics of the total ozone variations measured by the ground-based Brewer Ozone Spectrophotometer and the Total Ozone Mapping Spectrometer (TOMS) over Pohang are statistically examined from January 1994 to December 2004. First of all, in the correlation analysis of the total ozone measured from the Brewer Ozone Spectrophotometer and the TOMS, the correlation coefficient was 0.88 and the used data were 2190. The annual mean value of the total ozone is 311 DU with the standard deviation of 13 DU. The maximum and the minimum value were found in March (343 DU) and in September (282 DU), respectively. It was also revealed that the longest seasonal variation is in Spring (341 DU) and the smallest is in Autumn (283 DU). The time series data of the total ozone indicates that the annual variation is significant and the variations for three months and six months are relatively weak. Finally, the annual mean total ozones in Pohang (Brewer), Seoul (Brewer) and Busan (TOMS) are 312 DU, 324 DU and 304 DU, respectively.

Due to the temporal and spatial simultaneity and the high-frequency repetition, the data set retrieved from the satellite observation is considered to be the most desirable ones for the study of air-sea interaction. With rapidly developing sensor technology, satellite-retrieved data has experienced improvement in the accuracy and the number of parameters. Nevertheless, since it is still impossible to directly measure the heat fluxes between air and sea, the bulk method is an exclusive way for the evaluation of the heat fluxes at the sea surface. It was noted that the large deviation of air temperature in the winter season by the linear regression despite good correlation coefficients. We propose a new algorithm based on the Fourier series with which the SST and the air temperature. We found that the mean of air temperature is a function of the mean of SST with the monthly gradient of SST inferred from the latitudinal variation of SST and the spectral energy of air temperature is related linearly to that of SST. An algorithm to obtain the air temperature over the sea was completed with a proper analysis on the relation between of air temperature and of SST. This algorithm was examined by buoy data and therefore the air temperature over the sea can be retrieved based on just satellite data.

This study aims to estimate a heat island potential distribution based on the land-use types using LANDSAT/TM(1100LST April 2000) and AWS data in Daegu. The heat island potential is defined as a difference between surface temperature and air-temperature at each place. The study area was selected as about $900k km^2$ square including Daegu metropolitan area. Land-use data obtained by dividing all of Daegu metropolitan area into l-km-square three types of maps were prepared, in the 1 960s, 1970s and 2000s respectively. The types of land-use were divided into 5. Forest and farm lands have been reduced at a wide range during 40 years, most of which changed to urban area. The heat island potential distribution presented a striking contrasts according to land-use types. For example, the heat island potential of urban area was higher than $14^{\circ}$ in comparison to those of water or paddy rice areas.

Droughts have been an important factor in disaster management in Korea because she has been grouped into nations of lack of water. Satellite imagery can be applied to droughts monitoring because it can afford periodic data for large area for long time. This study aims to develop a method to analyze droughts in large area using satellite imagery. We estimated evapotranspiration in large area using NDVI data acquired from satellite imagery. For satellite imagery, we dealt with MODIS data operated by NASA. As the result of this study, we improved the usability of satellite imagery, especially in drought analysis.

The purpose of this study is to analyze the land cover environment changes of tidal flat in the Hampyeong Bay. Especially, it centers on the changes in the sedimentary environment using remote sensing data. Multi-temporal Landsat data (Path-Row: 116-034) were used in this study. Remote sensing data can be effectively applied for quantitative analysis of geological environment changes in the Hampyeong-bay.

In order to evaluate the Capability of ETM+ remotely- sensed data to provide 'Forest-shrub land-Rangeland' cover type map in areas near the timberline of northern forests of Iran, the data were analyzed in a portion of nearly 790 ha located in Neka-Zalemroud region. First, ortho-rectification process was used to correct the geometric errors of the image, yielding 0/68 and 0/69 pixels of RMS. error in X and Y axis, respectively. The original and panchromatic bands were fused using PANSHARP Statistical module. The ground truth map was made using 1 ha field plots in a systematic-random sampling grid, and vegetative form of trees, shrubs and rangelands was recorded as a criteria to name the plots. A set of channels including original bands, NDVI and IR/R indices and first components of PCI from visible and infrared bands, was used for classification procedure. Pair-wise divergence through CHNSEL command was used, In order to evaluate the separability of classes and selection of optimal channels. Classification was performed using ML classifier, on both original and fused data sets. Showing the best results of $67\%$ of overall accuracy, and 0/43 of Kappa coefficient in original data set. Due to the results represented above, it's concluded that ETM+ data has an intermediate capability to fulfill the spectral variations of three form- based classes over the study area.

We used a series of Landsat images acquired from 1984 to 2001 to observe decadal changes of the research forest of Kangwon National University. Tree NDVI images of November in 1984, 1986 and 2001 were displayed in RGB color composite. This image enabled us to identify historical change of conifer types and their approximate ages. Conifers were classified into 'old conifer aged more than 25 years', 'young conifer aged 20-25 years' 'very young conifer aged less than 20 years', and recently deforested areas. The results coincide with in situ data very well. Archives of higher resolution images should be used to monitor the change of area for various tree types.

In this study, 8 Landsat(TM/ETM+) satellite images acquired from 1984 to 2002 were used to investigate the growth of Chuncheon city, Kangwon-do, Korea. The images were geocoded and classified using training set collected from field survey. Four land-use types were classified such as urban area, green zone, agricultural land and water body. It also showed rapid increase of urban area in the past two decades from 1166ha in 1984 to 3358ha in 2002. About 2182ha of agricultural land and green zone have been changed to urban area. Agricultural land was newly formed from the green zone.

In order to retrieve the latent and sensible heat fluxes, high-resolution airborne imageries with visible, near infrared, and thermal infrared bands and ground-base meteorology measurements are utilized in this paper. The retrieval scheme is based on the balance of surface energy budget and momentum equations. There are three basic surface parameters including surface albedo $(\alpha)$, normalized difference vegetation index (NOVI) and surface kinetic temperature (TO). Lowtran 7 code is used to correct the atmosphere effect. The imageries were taken on 28 April and 5 May 2003. From the scattering plot of data set, we observed the extreme dry and wet pixels to derive the fitting of dry and wet controlled lines, respectively. Then the sensible heat and latent heat fluxes are derived from through a partitioning factor A. The retrieved latent and sensible heat fluxes are compared with in situ measurements, including eddy correlation and porometer measurements. It is shown that the retrieved fluxes from our scheme match with the measurements better than those derived from the S-SEBI model.

In this study, we analyzed surface temperature of lakes in the Han River system, using Landsat-5 and -7 time-series images. Surface temperature was extracted using NASA equation and compared with in situ 10m-depth temperature in Lake Soyang and surface temperature on five other dam lakes downstream. The 24 images out of 29 showed standard deviation of temperature difference less than $2^{\circ}C$, to which a novel statistical atmospheric correction could be applied. The correlation coefficients were 0.950 at Lake Soyang and 0.979-0.997 at the other lakes after atmospheric correction.

Spectral characteristics depending on soil constituents and their proportion in a soil were firstly studied for monitoring of soil contamination using hyperspectral remote sensing. The reflectance spectra of heavy metals in soils were investigated in the VIS-NIR-SWIR regions (400-2500 nm) to observe spectral variation as a function of constituents and concentrations. Commercial kaolinite soils mixed with lead, copper, arsenic, and cadmium were used as synthetic soil samples for spectral measurement. In case of copper, relatively spectrally active regions was observed with some band shift whereas other heavy metals had only simple spectral variations expected to be related to the sorption phase and the amount of metal onto kaolinite. The reflectance spectrum of each metal on kaolinite could be identified in VIS-NIR region.

In order to evaluate KOrea Multi-Purpose SATellite (KOMPSAT) application products and develop the multi-sensor data application technologies, the Product Validation Site (PVS) will be designed and constructed by Korea Aerospace Research Institute (KARI). Also KARl has a plan for acquisition of multi-sensor data such as ENVISAT ASAR and Project for On Board Autonomy (PROBA) Compact High Resolution Imaging Spectrometer (CHRIS) data through international cooperation with European Space Agency (ESA). These data will be utilized with KOMPSAT-2 Multi-Spectral Camera (MSC) data. KARI and ESA have identified a mutual interest in creating synergy in the joint exploitation of Earth Observation data for science and applications both in Korea and Europe. This paper summarizes the status of joint experimental studies between KARI and ESA for further applications and presents some expected results from related activities.

In this study, weight of evidence(WOE) technique based on the bayesian method was applied to estimate the groundwater yield characteristics in the Pocheon area in Kyungki-do. The ground water preservation depends on many hydrogeologic factors that include hydrologic data, landuse data, topographic data, geological map and other natural materials, even with man-made things. All these data can be digitally collected and managed by GIS database. In the applied technique of WOE, The prior probabilities were estimated as the factors that affect the yield on lineament, geology, drainage pattern or river system density, landuse and soil. We calculated the value of the Weight W+, W- of each factor and estimated the contrast value of it. Results by the ground water yield characteristic calculations were presented in the form of posterior probability map to the consideration of in-situ samples. It is concluded that this technique is regarded as one of the effective technique for the feasibility mapping related to detection of groundwater bearing zones and its spatial pattern.

Analysis method using remote sensing data is one of the effective ways to research a spatial and temporal variability of the mesoscale oceanic motions. During past several decades, many researchers have been getting comprehensive results using remote sensing data with application of data fusion methods in many parts of geo-science. For this study, we took the integration and fusion of several remote sensing data, which are different data resolution, timescale and characteristics, for improving accurate analysis of variation of the Kuroshio Extension. Furthermore, we might get advanced ways to understand the variability of the Kuroshio Extension, has close relation to the spatial and temporal variation of the Kuroshio and Oyashio Current.

We examined the relationship between the 50m temperature estimated by remote sensing sea surface temperature (SST) and fishing ground (squid fishing ground) detected by nighttime visible channel defense meteorological satellite program (DMSP) I operational linescan system (OLS) images in the East/Japan Sea during 1993-2000. The results are as follows: The numbers of nighttime fishing boat were distributed the highest in October, and the lowest in April during this study. A nighttime fishing grounds have concentrated in the East Korea Warm Current region, coastal regions of Honshu Island, and Polar front region. Fishing grounds have distributed $11-18^{\circ}C$ of estimated 50m temperature from the satellite data. Relationship between estimated 50m temperature and the distributed fisheries boats showed that the north boundaries of fishing grounds have distributed the temperature of below $12^{\circ}C$ from 1996 to 2000 and that of $13-15^{\circ}C$ during 1993-1995 and 1997-1999. Stable fishing grounds appeared near the Korea/Tsushima Strait from January to March. The center of fishing grounds in spring (April-Jun) have moved to the northward than that in winter, and variations appeared largely in winter. In summer (July-September), center of fishing grounds have formed near the Uleung Island in the south east coast of Korea, and in autumn maximum fishing ground appeared in October, the fishing ground southward from November.

The goal of this study is to investigate the relationship between microphytobenthic biomass and normalized vegetation index obtained from Landsat TM images. Monitoring a seasonal change of microphytobenthic biomass in the sand bar is specifically focused. Since the study area, Hampyeong Bay, was difficult to approach, we failed to obtain ground truths simultaneously on satellite image acquisition. Instead, chlorophyll-a concentration in surface top layer was measured on different dates for microphytobenthic biomass. Although data were acquired on different dates, a correlation between the field and satellite images was calculated for investigating general trends of seasonal change. NDVI and tasseled cap transformed images were also used to review the variation of microphytobenthic biomass by using Landsat TM and ETM+ images. Atmosphere effects were corrected by applying COST model. Seaweeds were also flouring in the same season of microphytobentic blooming. Songseok-ri area was minimally affected by seaweeds from February to May, and selected as a test site. NDVI value was classified into high-, moderate-, and low-grade. It was well developed over fme-grained sediments and rapidly reduced from May to November over sand bar. In this bay, correlation between grain size and microphytobenthic biomass was clearly seen. From the classified NDVI and tasseled cap transformed data, we finally constructed spatial distribution and seasonal variation maps of microphytobenthic biomass.

Various methods to detect the phytoplankton/red tide blooms in the oceanic waters have been developed and tested on satellite ocean color imagery since the last two and half decades, but accurate detection of blooms with these methods remains challenging in optically complex turbid waters, mainly because of the eventual interference of absorbing and scattering properties of dissolved organic and particulate inorganic matters with these methods. The present study introduces a new method called Red tide Index (Rl), providing indices which behave as a good measure of detecting red tide algal blooms in high scattering and absorbing waters of the Korean South Sea and Yellow Sea. The effectiveness of this method in identifying and locating red tides is compared with the standard Ocean Chlorophyll 4 (OC4) bio-optical algorithm applied to SeaWiFS ocean imagery, acquired during two bloom episodes on 27 March 2002 and 28 September 2003. The result revealed that OC4 bio-optical algorithm falsely identifies red tide blooms in areas abundance in colored dissolved organic and particulate inorganic matter constituents associated with coastal areas, estuaries and river mouths, whereas red tide index provides improved capability of detecting, predicting and monitoring of these blooms in both clear and turbid waters.

A forest fire occurs mainly as natural factor such as wind, temperature or human factor such as light. Recently, the most of forest fire prevention is prediction or prevision against forest fire by using remote sensing technology. However in order to forest fire prevention, the remote sensing has many limitations such as high cost and advanced technologies and so on. Therefore, we need to multisensor integration system that utilize not only remote sensing but also in-situ sensing in order to reduce large damage of forest fire though analysis of happen cause and prediction routing of occurred forest fire. In this paper we propose a multisensor integration system that offers prediction information of factors and route of forest fire by integrates collected data from remote sensor and in-situ sensor for forest fire prevention. The proposed system is based on wireless sensor network for collect observed data from various sensors. The proposed system not only offers great quality information because firstly, raw data level fuse different format of collected data from remote and in-situ sensor but also accomplish information level fusion based on result of first stage. Offered information from our system can help early prevention of factor and early prevision against occurred forest fire which transfer to SMS service or alert service into monitoring interface of administrator.

Mining frequent patterns in transaction databases, time-series databases, and many other kinds of databases has been studied popularly in data mining research. Most of the previous studies adopt an Apriori-like candidate set generation-and-test approach. However, candidate set generation is still costly, especially when there exist prolific patterns and/or long patterns. And calendar based on temporal association rules proposes the discovery of association rules along with their temporal patterns in terms of calendar schemas, but this approach is also adopt an Apriori-like candidate set generation. In this paper, we propose an efficient temporal frequent pattern mining using TFP-tree (Temporal Frequent Pattern tree). This approach has three advantages: (1) this method separates many partitions by according to maximum size domain and only scans the transaction once for reducing the I/O cost. (2) This method maintains all of transactions using FP-trees. (3) We only have the FP-trees of I-star pattern and other star pattern nodes only link them step by step for efficient mining and the saving memory. Our performance study shows that the TFP-tree is efficient and scalable for mining, and is about an order of magnitude faster than the Apriori algorithm and also faster than calendar based on temporal frequent pattern mining methods.

Surface Solar Insolation is important for vegetation productivity, hydrology, crop growth, etc. However, ground base measurement stations installed pyranometer are often sparsely distributed, especially over oceans. In this study, Surface Solar Insolation is estimated using the visible and infrared spin scan radiometer(VISSR) data on board Geostationary Meteorological Satellite (GMS)-S covering from March 2001 to December 2001 in clear and cloudy conditions. To retrieve atmospheric factor, such as, optical depth, the amount of ozone, H20, and aerosol, SMAC (Simplified Method for Atmospheric Correction) code, is adopted. The hourly Surface Solar Insolation is estimated with a spatial resolution of $5km\;\times\;5km$ grid. The daily Surface Solar Insolation is derived from the available hourly Surface solar irradiance, independently for every pixel. The pyranometer by the Korea Meteorological Agency (KMA) is used to validate the estimated Surface Solar Insolation with a spatial resolution of $3\;\times\;3Pixels.$

The ITT Industry's Commercial Advanced Geo-Imager (CAGI) which is a recurrent version of imagers used in the GOES series was selected as the COMS Meteorological Imager (MI). The ITT Imager can conduct some special observation such as the space look, blackbody observation, and star sensing regularly or irregularly for its radiometric quality control. Because the GOES-9 which uses an ITT Imager has become operational over the Western Pacific and Eastern Asia positioned at 155 degrees East, the reception of the GOES-9 data is available in Korea. As a step of preparing the COMS MI operation, we conduct the analysis of the GOES-9 imager raw data and operation procedures and compare them with contents of the ITT Imager's manual.

In this study e-map component was designed and developed to possibly overlay with all kinds of thematic maps in various scales and provide the all detailed information by using high-resolution satellite image and GIS. Also, this system has powerful map composition tool to display map such as legend, scale bar, index map and so on. For this, this e-map component was designed by using UML and developed based on Windows 2000 and implemented by using Visual Basic 6.0 as development programming language, Map Objects 2.1 of ESRI as GIS component. Through this system, the forest officials could generate more detailed topography and desired thematic map. In addition, the data consistency in DBMS could be maintained by using SDE (Spatial Database Engine) for their job and share the standard forest database with others in real time.

This paper proposes a reconstruction method for the shape and color information of 3-dimensional buildings. The proposed method is range scanning by laser range finder and image coordinates' color information mapping to laser coordinate by a fixed CCD camera on laser range finder. And we make a 'Far-View' using high-resolution satellite image. The 'Far-View' is created that the height of building using DEM after contours of building extraction. The user select a region of 'Far View' and then, appear detailed 3D-reconstruction of building The outcomes apply to city plan, 3D-environment game and movie background etc.

In tactical theater, it is crucial to detect ground moving targets and to locate them precisely. This problem can be resolved by using SAR (Synthetic Aperture Radar) sensors providing GMTI (Ground Moving Target Indication) capability. In general, to implement a robust GMTI sensor is not simple because of the strong competitions between target signals and clutter signals on the ground, and low speed of moving targets. Contrary to the case that a delay canceller is mostly suitable for ground surveillance radars, DPCA (Displaced Phase Centered Antenna) or STAP (Space Time Adaptive Processing) techniques have been adapted for GMT! function of modem airborne radars. In this paper, anew scheme of DPCA using two passive antennas with vertical separation is proposed, which also provides good clutter cancellation performance. The proposed scheme enables us to scan straight ahead of the carrying platform that is impossible with typical DPCA configuration. Simulations using various conditions have been performed to validate the proposed scheme, and the results are acceptable.

The PMU (Payload Management Unit) is the main subsystem for the management, control and power supply of the MSC (Multi-Spectral Camera) Payload operation. It is the most important function for the electro-optical camera system that performs the Non-Uniformity Correction (NUC) function of the raw imagery data, rearranges the data from the CCD (Charge Coupled Device) detector and output it to the Data Compression and Storage Unit (DCSU). The NUC board in PMU performs it. In this paper, the NUC board system is described in terms of the configuration and the function, the efficiency for non-uniformity correction, and the influence of the data compression upon the peculiar feature of the CCD pixel. The NUC board is an image-processing unit within the PMU that receives video data from the CEV (Camera Electronic Unit) boards via a hotlinkand performs non-uniformity corrections upon the pixels according to commands received from the SBC (Single Board Computer) in the PMU. The lossy compression in DCSU needs the NUC in on-orbit condition.

The Modulation Transfer Function (MTF) is commonly used to characterize the spatial quality of imaging systems. This work is the attempt to measure the MTF at Nyquist frequency of the satellite imaging system what has 1m spatial resolution for KOMPSAT-2 image using the edge function. Artificial tarp targets are used in this study. A type of this tarp edge consists of two adjacent uniform bright and dark sides commonly used to test the performance of an optical system in edge function. The results from this work demonstrate the potential applicability of this method to estimate the response characteristics for KOMPSAT-2 that is scheduled to be launched.

The 2nd KOrea Multi-Purpose Satellite (KOMPSAT -2) has been developed by Korea Aerospace Research Institute (KARI) since 2000. Multi Spectral Camera (MSC) is the payload for KOMPSAT -2, which will provide the observation imagery around Korean peninsula with high resolution. KOMPSAT-2 has adopted X-band Tracking System (XTS) for transmitting earth observation data to ground station. For this, data which describes and controls the pre-defined motion of each on-board X-Band antenna in XTS, must be transmitted to the spacecraft as S-Band command and it is called as Tracking Parameter Files (TPF). In this paper, the result of the development of TPF Generation S/W for KOMPSAT-2 X-Band Antenna Motion Control.

As a former level of MSC(Multi Spectral Camera) telescope of the KOMPSA T2satellite, the several performance tests of EOS(Electro Optical Subsystem) were performed in the EOS level. By these tests, not only the design requirement of payload can be verified but also the test result can be the important criterion to estimate the performance of payload in the launch and space orbit environment. The EOS Geometric Mapping test is to verify the accuracy of the alignment & assembly on the Subsystem of the MSC by measurement like these; LOS(Line of Sight), LOD(Line of Detector), Band to Band Registration, Optical Distortion and Reference Cube. This paper describes the test results and the analysis for the EOS Geometric Mapping.

The PMU (Payload Management Unit) in MSC (Multi-Spectral Camera) is the main subsystem for the management, control and power supply of the MSC payload operation. The PMU shall handle the communication with the BUS (Spacecraft) OBC (On Board Computer) for the command, the telemetry and the communications with the various MSC units. The PMU will perform that distributes power to the various MSC units, collects the telemetry reports from MSC units, performs thermal control of the EOS (Electro-Optical Subsystem), performs the NUC (Non-Uniformity Correction) function of the raw imagery data, and rearranges the pixel data and output it to the DCSU (Data Compression and Storage Unit). The BUS provides high voltage to the MSC. The PMU is connected to primary and redundant BUS power and distributes the high unregulated primary voltages for all MSC sub-units. The PSM (Power Supply Module) is an assembly in the PMU implements the interface between several channels on the input. The bus switches are used to prevent a single point system failure. Such a failure could need the PSS (Power Supply System) requirement to combine the two PSM boards' bus outputs in a wired-OR configuration. In such a configuration if one of the boards' output gets shorted to ground then the entire bus could fail thereby causing the entire MSC to fail. To prevent such a short from pulling down the system, the switch could be opened and disconnect the short from the bus. This switch operation is controlled by the BUS.

Research and development of remote sensing technique is necessary so that more accurate and extensive information may be obtained. To achieve this goal, the synthesized technique which integrates the high resolution optic and SAR image, and topographical information was examined to investigate the quantitative/qualitative characteristics of the Earth's surface environment. For this purpose, high-precision DEMs of Jeju-Island was generated and data fusion algorithm was developed in order to integrate the multi-spectral optic and polarimetric SAR image. Three dimensional land-cover and two dimensional soil moisture maps were generated conclusively so as to investigate the Earth's surface environments and extract the geophysical parameters.

In general, most incomplete communication link setup between satellite and ground station right after separation from launcher come from less accurate orbital vector ground station uses to track the satellite because only predicted orbital state vector is available during first few orbits. This paper describes the developed procedure for successful initial acquisition for KOMPSAT-2 using scanning functions ofK13 antenna system with predicted orbital information. Azimuth scan, raster scan, spiral scan functions were tested with KOMPSA Tl under intentionally degraded orbital information for antenna operation. Through tests, spiral scan function was decided to be best search scan among 3 scans. Developed procedure can assure the successful acquisition only if azimuth offset and time offset value are within +/-2deg and +/-30sec, respectively.

Wavelet scheme can be applied to the various remote sensing problems: conventional multi-resolution image analysis, compression of large image sets, fusion of heterogeneous sensor image and segmentation of features. In this study, we attempted wavelet-based filtering and its analysis. Traditionally, statistical methods and adaptive filter are used to manipulate noises in the image processing procedure. While we tried to filter random noise from optical image and radar image using Discrete Wavelet Transform (DW1) and Stationary Wavelet Transform (SW1) and compared with existing methods such as median filter and adaptive filter. In result, SWT preserved boundaries and reduced noises most effectively. If appropriate thresholds are used, wavelet filtering will be applied to detect road boundaries, buildings, cars and other complex features from high-resolution imagery in an urban environment as well as noise filtering

KOMPSAT -2 equipped with an optical telescope(MSC) will be launched in this year. It can take images of the earth with push-broom scanning at altitude 685Km. Its resolution is 1m in panchromatic channel with a swath width of 15 km After the MSC is tested and the performance is measured at instrument level, it is installed on satellite. The image passes through the electro-optical system, compression and storage unit and fmally downlink sub-systems. This integration procedure necessitates the functional test of all subsystems participating in the image chain. The objective of functional test at satellite level(Quick Look test) is to check the functionality of image chain by real target image. Collimated moving image is input to the EOS in order to simulate the operational environments as if KOMPSAT -2 is being operated in orbit. The image chain from EOS to data downlink subsystem will be verified through Quick Look test. This paper explains the Quick Look test of KOMPSAT -2 and compares the taken images with collimated input ones.

Accurate DEM surface of forest floor is very important to extract any meaningful information regarding forest stand structure, such as tree heights, stand density, crown morphology, and biomass. In airborne lidar data processing, DEM data of forest floor is mostly generated by interpolating those elevation points obtained from last laser returns. In this study, we try to analyze the property of the last laser return under relatively dense forest canopy. Airborne laser data were obtained over the study area in relatively dense pine plantation forest. Two DEM data were generated by using all the points in the last laser returns and using only those points after removing non-ground points. From the preliminary analysis on these DEM data, we found that more than half of points among the last laser returns are actually hit from canopy, branches, and understory vegetation that should be removed before generating the surface DEM data.

LiDAR(Light Detection and Ranging) with digital aerial photograph can be used to measure tree growth factors like total height, height of clear-length, dbh(diameter at breast height) and crown projection area. Delineating crown is an important process for identifying and numbering individual trees. Crown delineation can be done by watershed method to segment basin according to elevation values of DSMmax produced by LiDAR. Digital aerial photograph can be used to validate the crown projection area using LiDAR. And tree height can be acquired by image processing using window filter$(3cell\times3cell\;or\;5cell\times5cell)$ that compares grid elevation values of individual crown segmented by watershed.

In recent years, LiDAR(Light Detection and Ranging) data has been widely used to prepare digital elevation models(DEMs) with the high spatial resolution of centi-meters. This paper investigated possible applications of LiDAR-derived DEMs in surface hydrology modeling, such as characterizing flow direction, identifying sub-basins in a watershed, and calculating variables like upstream contribution area. The results were compared to the results of the DEMs from conventional topographic maps.

Light detection and ranging (LIDAR) is one of the effective technologies for monitoring forest inventory, and importance of forestry is increasing because of its function as the sink of green house gases (GHG). This study aims at development of a methodology for better and more accurate estimation of physical parameters of individual trees by removing sudden drops of LIDAR data within a crown. Our study area is located in Aomori prefecture, the northern part of Honshu Island, with the dominant species of Japanese cedar. The results show practicality of our method in the usage of LIDAR data in the field of forest inventory.

Dual-channel Radiometers for Earth and Atmosphere Monitoring (DREAM) is the Korean first spaceborne microwave radiometer which is the main payload of Science and Technology SATellite-2 (STSAT-2). STSAT-2 will be launched by Korea Space Launch Vehicle-l (KSL V-I) at NARO Space Center in Korea in 2007. DREAM is a two-channel, total power microwave radiometer with the center frequencies of 23.8 GHz and 37 GHz. The spaceborne radiometer is composed of an antenna unit, a receiver unit, and a data acquisition/processing unit. The bandwidths of radiometer are 600 MHz at 23.8 GHz and 1000 MHz at 37 GHz. The integration time of two channels is 200 rns. The sensitivity of DREAM is less than 0.5 K. This paper presents the required performance and system design of DREAM in detail.

A raw signal simulator for synthetic aperture radar (SAR) is a useful tool for the design and implementation of SAR system. Also, in order to analyze and verify the developed SAR processor, the raw signal simulator is required. Moreover, there is the need for a test system to help designing new SAR sensors and mission of SAR system. The derived parameters of the SAR simulator also help to generate accurate SAR processing algorithms. Although the ultimate purpose of this research is to presents a general purpose SAR simulator, this paper presents a SAR simulator in frequency domain at the first step. The proposed simulator generates the raw signal by changing various simulation parameters such as antenna parameters, modulation parameters, and sampling parameters. It also uses the statistics from an actual SAR image to imitate actual physical scattering. This paper introduces the procedures and parameters of the simulator, and presents the simulation results. Experiments have been conducted by comparing the simulated raw data with original raw SAR image. In addition, the simulated raw data have been verified through commercial SAR processing software.

Polarization of the radar wave refers to the ellipticity angle and orientation angle of the polarization ellipse. An evaluation of the polarization response can help understand the scattering mechanisms involved for a particular area of interest or provide information for image classification and algorithm section. C- and L-band polarization responses measured at urban area show the results that the polarization behavior for dihedral comer reflector or short, thin cylinder reflector appears at located in city streets or buildings site which are lined up and the polarization behavior for a large conducting sphere appears at parts of test site particularly river, flat, and vegetated areas. Also, the co- and cross-polarized response graphs and polarimetric parameters are discussed.

Tidal flats develop along the south coast ofthe Korean peninsula. These areas are famous for sea farming. Specially, strong and coherent radar backscattering signals are observed over oyster sea farms that consist of artificial structures. Tide height in oyster farm is possible to measure by using interferometric phase and intensity of SAR data. It is assumed that the radar signals from oyster farm could be considered as double-bouncing returns by vertical and horizontal bars. But, detailed backscattering mechanism and polarimetric characteristics in oyster farm had not been well studied. We could not demonstrate whether the assumption is correct or not and exactly understand what the properties of back scattering were in oyster farm without full polarimetric data. The results of AIRSAR L-band POLSAR data, experiments in laboratory and JERS-l images are discussed. We carried out an experiment simulating a target structure using vector network analyser (Y.N.A.) in an anechoic chamber at Niigata University. Radar returns from vertical poles are stronger than those from horizontal poles by 10.5 dB. Single bounce components were as strong as double bounce components and more sensitive to antenna look direction. Double bounce components show quasi-linear relation with height of vertical poles. As black absorber replaced AI-plate in bottom surface, double bounce in vertical pole decreased. It is observed that not all oyster farms are characterized by double bounced scattering in AIRSAR data. The image intensity of the double bounce dominant oyster farm was investigated with respect to that of oyster farm dominated by single bounce in JERS-l SAR data. The image intensity model results in a correlation coefficient (R2 ) of 0.78 in double bounce dominant area while that of 0.54 in single bouncing dominant area. This shows that double bounce dominant area should be selected for water height measurement using In8AR technique.

Spaceborne radar interferometry has been widely used to estimate the topography and deformation of the Earth. It is difficult to obtain coherent interferometric SAR pairs especially over coastal areas mainly because of variation of surface conditions. We carried out the experiment using a cross-interferometric pair with a perpendicular baseline of about 1.4 km, a 30 minutes temporal separation and the height sensitivity of about 6 meters. The temporal decorrelation can be reduced by the cross interferometric technique with a 30 minutes temporal separation. Accurate coregistration was performed through resampling of ENVISAT ASAR data to equivalent pixel spacing to the ERS SAR data, because of the differences of the pulse repetition frequency and range sampling rate between the two sensors. Then we estimated range and azimuth offset to a sub-pixel accuracy using image intensity cross correlation. A larger window chip size than a general case was used because it was difficult to distinguish typical features. As range bin increased, the difference of Doppler centroid also increased. It resulted in lower coherence in far range than in near range. Coherences over wetland in near and far range were about 0.8 and 0.5, respectively. The coherence was improved by applying azimuth and range common band filtering, but coherence gap still existed. ERS-ENVISAT cross-interferogram usually lost information in urban area. However, high coherence over a city in this pair was shown, because of less man-made structures than other major cities. Accuracy of the DEM constructed by the ERS-ENVISAT 30-minute pair in a coastal area is to be evaluated.

It is evident that advancement of ubiquitous technologies in the near future guarantees more convenient and plentiful living. With regarding to car life, we dream of an automatic driving without any effort of operation. This paper touches the realization issue, a convergence of wireless sensor network and Telematics specializing on an information routing mechanism between participating components in Telematics sensor communication network. We list up new requirements of wireless sensor network deployed for Telematics services. Then context-aware routing architecture is proposed in order to solve these constraints, in which a network topology for routing can be dynamically configured according to the combination of context models of network components.

To acquire radar target signature, various kinds of target are necessary. Measurement is one of the data acquiring method, but much time and high cost is required to get the target data from the real targets. Even if we can afford that, the targets we can access are very limited. To obtain target signatures avoiding these problems, we build the target CAD (Computer Aided Design) model for the calculation of target signatures. To speed up RCS calculation, we applied adaptive super-sampling and tested quite complex tank CAD model which is 1.4 hundred of thousands facet. We use calculated RCS data for ID range profile and 2D ISAR (Inverse Synthetic Aperture Radar) image formation. We adopted IFFT (Inverse Fast Fourier Transform) algorithm combined with polar formatting algorithm for the ISAR imaging. We could confirm the possibility of the construction of database from the images of CAD models for target classification applications.

Meteorological imager on the Multi-functional Transport Satellite (MTSAT-IR), which has been operating formally since 28 June 2005, was intercalibrated with a polar orbit satellite [Aqua Moderate Resolution Imaging Spectroradiometer (Aqua/MODIS)] as a well-calibrated instrument. The intercalibration method used in this study was developed by the Cooperative Institute for Meteorological Satellite Studies (CIMSS). This was done for the infrared window channels. The differences of MTSAT-IR and MODIS were are -0.26 K for $11\;\mu m-IR$ window channel, 0.40 K for $12\;\mu m-IR$, window channel, and -0.67 K for $6.7\;\mu m-water$ vapor channel.

The Korea Multi-Purpose SATellite-2 (KOMPSAT -2) will be launched into a circular sun synchronous orbit in Dec. 2005. For the mission operation of the KOMPSAT-2 satellite, KARl Ground Station (KGS) consists of the Mission Control Elements (MCE), Image Reception & Processing Elements (IRPE) and the overseas stations. For the oversea stations, the Kongsberg Satellite Services (KSAT) is the prime supplier of support service. KSAT has the capability to provide Tracking Telemetry and Commanding (TT&C) nominal, contingency and anomaly support for every single orbit for most polar orbiting satellites. Also KSAT provides nodal service through the network management functionality for all oversea ground stations. This paper describes the oversea stations and the support for Launch and nominal TT&C services for KOMPSAT-2 and the operation plan for KOMPSAT-2.

From the IF (Intermediated Frequency) loop-back test, BER (Bit Error Rate) degradation of processed data, HRIT (High Rate Information Transmission), is estimated by proposed measurement configuration. The specific parameters, likely data rate, FEC (Forward Error Correction), and modulation method, are based on the outcomes of SRR (System Requirements Review) which was held on 13-14 June 2005, in Toulouse. The proposed measurement procedure is that combined 70MHz modulated signal and noise is connected to the spectrum analyzer and receiver. The former measures the C/No (Carrier to Noise density ratio) and the latter estimates BER of FEC decoded data. Implementation loss can be obtained by subtracting measured BER from calculated BER which is also subtracted data rate from measured C/No. This test procedure is very simple and can be applied to assess the implementation loss of dedicated receiver for HRIT in the future.

The relation between HPA (High Power Amplifier) and COMS (Communication Ocean Meteorological Satellite) multi-carrier is analyzed in this paper. MODAC (Meteorological and Ocean Data Application Center) has a primary mission to transmit processed data, HRIT (High Rate Information Transmission) and LRIT (Low Rate Information Transmission), which is normalized and calibrated by pre-processing. It is also replaced with the SOC (Satellite Operation Center) in emergency case and can transmit the command and ranging tones for operation of COMS. From the result of simulation with modelled HPA, it is found that the multi-carrier in one HPA can give rise to an inter-modulation which makes harmonic and spurious elements increase in-band. Under the environment of these increased parasitic elements, the degradation of multi-carrier's quality is estimated from the ratio of the amount of noise to total output power of HPA.

Recently, as mobile paradigms such as telematics or LBS (Location Based Service) have been being more diverse and mobile devices such as PDA (Personal Digital Assistance) or several telematics terminals have been being used more widely, mobile services, for example, mobile geographic information service have been being put more importance by people. In this paper, we propose to adopt S/W and data streaming mechanism as a method to improve performance of mobile geographic information service which is a representative of mobile services based on client-server architecture. The show the effectiveness of proposed methods, we design and implement S/W streaming prototype system and sample mobile geographic information service to be executed on the S/W streaming system.

In this paper, we propose an efficient image segmentation technique for large-sized monochrome images using a hybrid approach which combines threshold and region-based techniques. First, an image is partitioned into fixed-size blocks and for each block the representative intensity is determined by averaging pixel intensities within the block. Next, the neighborhood blocks that have similar characteristics with respect to a specific threshold are merged in order to form candidate regions. Finally, those candidate regions are refined to get final target object regions by merging regions considering the spatial locality and certain criteria. We have performed experiments on images selected from various domains and showed that our technique was able to extract target object regions appropriately from most images.

Topographical images, in case of aerial or satellite images, are usually similar in colors and textures, and complex in shapes. Thus we have to use shape features of images for efficiently retrieving a query image from topographical image databases. In this paper, we propose a shape feature extraction method which is suitable for topographical images. This method, which improves the existing projection in the Cartesian coordinates, performs the projection operation in the polar coordinates. This method extracts three attributes, namely the number of region pixels, the boundary pixel length of the region from the centroid, the number of alternations between region and background, along each angular direction of the polar coordinates. It extracts the features of complex shape objects which may have holes and disconnected regions. An advantage of our method is that it is invariant to rotation/scale/translation of images. Finally we show the advantages of our method through experiments by comparing it with CSS which is one of the most successful methods in the area of shape feature extraction

One of the latest wonders brought to us by ICT(Information and Communication Technology) is telematics turning automobiles, not long ago a mere means of transportation, into a whole-new digital living space. Telematics is indeed fast becoming a household word, and countries around the globe are giving spur to research and development of core technologies to acquire competitiveness in related IT sectors. This paper discusses the telematics pilot project launched in Jeju to promote the development of telematics technology and stimulate related industries. The objective of the pilot project is to give impetus to research in related technologies and a head-start to Korea in the global race in this technology field. The pilot deployment, covering 6 services, promising to be most demanded in Korea's telematics environment, is sure to make a sizeable contribution toward familiarizing the public with the new technology.

The Geostationary Operational Environmental Satellite (GOES) 9, which is currently located at 155°E geostationary orbits, has transmitted earth observation data acquired by imager to CDA at NOAA. After the acquisition on ground, observation data are corrected on ground and re-transmitted to GOES-9 for the dissemination to users. In this paper, the procedure and result from raw data acquisition and pre-processing for earth observation imagery retrieval from GOES-9 Raw data acquired in Korea at May 2005 are introduced.

The MSC (Multi Spectral Camera) system is a remote sensing payload to obtain high resolution ground image. This system uses lossy image compression method for &Direct mission& that transmit whole image during one contact. But some image degradation occurred especially at high compression ratio. To reduce this degradation, the MSC uses NUC (Non-uniformity Correction) Unit. This unit correct CCD (Charge Coupled Device)'s high-frequency non-uniformity. So high frequency contents of image can be minimized and whole system SNR can be maximized. But NUC has some disadvantage either. It decreases entire system reliability by adding one electronic system. Adding NUC also led to difficulty of electronic design, assembly and testability. In this paper, the comparison is performed between on-orbit non-uniform correction and on ground correction. by evaluating NUC advantage for the point of view of image quality. Using real MSC parameter and proper model, considerable reference point for the system design came to possible.

Gravity characteristics and Moho undulations are investigated in the Korean peninsula by using satellite gravity data. According to the development of satellite geodesy, gravity potential models which have high accuracy and resolution were released. Using the EIGEN-CGOIC model based on low orbit satellite data such as CHAMP and GRACE, geoid and gravity anomaly were calculated by spherical harmonic analysis. The study area is located at $123^{\circ}\sim132^{\circ}E, 33^{\circ}\sim43^{\circ}$N including Korea. Free-air anomalies, which show the effect of terrain, have the values between $-37\sim724 mgal. After Bouguer correction, the range of simple Bouguer anomalies is $-221\sim246$ mgal. Complete Bouguer anomalies after terrain correction increase from continent to marine. This phenomenon is related rise of Moho discontinuity. The cut-frequency for extraction of Moho undulation was determined by power spectrum analysis, and then 3D inversion modeling was implemented. The mean, maximum, minimum, and standard deviation of Moho depth undulation are -26, -36, -8, and 4.9 krn, respectively.

The MSC is a remote sensing instrument with very high performance that is to be installed on KOMPSAT2 satellite. The MSC consists of EOS (Electro-Optic Subsystem), PMU (Payload Management Unit) and PDTS (Payload Data Transmission Subsystem). PMU controls and monitors all the other payload units by sending commands and collecting telemetry. PMU is in charge of interfacing between payload system and satellite bus system. PMU gets commands from ground-station via OBC (On-Board Computer) that is a main controller of the satellite bus system and sends telemetry to the ground-station via OBC. There is a processor module, called SBC (Single Board Computer) in the PMU. The SBC is a main controller of the MSC system. The main roles of the SBC are payload mission management, command validation and execution, telemetry collection and monitoring, ancillary data handling, event reporting, power control of payload sub-units and communication with these units. Intel's 80486DX2 processor has been used for the SBC. Due to the fact that the SBC plays important roles for imaging mission execution and handles a lot of control data that is required for payload operation, it is required to make analysis of the CPU load when it is in maximum operation mode. In this paper, the analysis and measurement results of the SBC throughput in the maximum operation mode.

The software streaming technology enables telematics software to be automatically updated through a wireless network. When the software starts running, software streaming system inspects its version and then, automatically download latest one. The software streaming system breaks the software into several pieces that are streamed to the user as needed. In this way, software streaming system can improves the telematics application load time while updating the software through wireless network. In our experiments, the application load time was reduced about 7 times compared to downloading whole software at best case.

Refocusing methods are used to compensate optical performance degradation of high resolution satellite camera during on-orbit operation. Due to mechanical vibration during launch and thermal vacuum environment of space where camera is exposed, the alignment of optical system may have error. The focusing error is dominant of misalignment and caused by the de-space error of secondary mirror of catoptric camera, which is most sensitive to vibration and space environment. The high resolution camera of SPOT, Pleiades and KOMPSAT2 have refocusing device to adjust focusing during orbital operation while QuickBird of US does not use on orbit refocusing method. For the Korsch type optical configuration which is preferred for large aperture space remote sensing camera, secondary mirror and folding mirror are available as refocusing element.

All CCD pixels do not react uniformly even if the light of same radiance enters into the camera. This comes from the different camera optical characteristics, the read-out characteristics, the pixel own characteristics and so on. Usually, the image data of satellite camera can be corrected by the various image-processing methods in the ground. However, sometimes, the in-orbit correction is needed to get the higher quality image. Especially high frequency pixel correction in the middle of in-orbit mission is needed because the in-orbit data compression with the high frequency loss is essential to transmit many data in real time due to the limited RF bandwidth. In this case, this high frequency correction can prevent have to have any unnecessary high frequency loss. This in-orbit correction can be done by the specific correction table, which consists of the gain and the offset correction value for each pixel. So, it is very important to get more accurate correction table for good correction results. This paper shows the new algorithm to get accurate pixel correction table. This algorithm shall be verified theoretically and also verified with the various simulation and the test results.

The existing wired emergency call such as 119, 112 have its own location information to serving immediate rescue service. For the case of wireless emergency call by mobile phone, the location information should be provided by wireless network. This paper describes the network architecture and protocol for mobile emergency service referring TIAlEWJ-SID-036-A with reviews about technical issues, legacy factors and related researches. The mobile emergency service is divided into mobile emergency rescue service and mobile emergency alert service. The network reference model for mobile emergency rescue service is released in KOREA. In this paper, the interfaces between elements of the network reference model, and service scenarios, message flows are defined. Supplement to mobile emergency rescue service, the network reference model, interfaces and message flows for mobile emergency alert service are developed. The protocol is described by DID, and the proposed works are on processing for domestic standard of TTA.

Korea Aerospace Research Institute(KARl) has been receiving Terra and Aqua MODIS data at ground station of Daejeon since July 2002. MODIS data can cover whole East Asia including the Korean Peninsula, Japan and The East China each almost scene and is monitoring ocean, atmosphere and land. By this time, over two thousand scenes have been archived including Terra and Aqua in the storage system and they occupied about over 10TB of disk space. In this study, Web-Downloading system of MODIS data developed on WWW is including following main functions: spectral subset (250m, 500m, 1000m chnnels) Level 1B data of HDF format, result display, ftp download and statistic viewer etc. Users using this system can directly download MODIS data on WWW with a few input parameters. This system is available via the Internet URL after October 2005 on the following, 'http://webmodis.kari.re.kr/'

CALNAL team of Korea Aerospace Research Institute(KARI) performed field campaigns for absolute radiometric calibration of 1m satellite image on Daejeon and the cal/val site of Goheung. The satellite image have spatial resolution of 1m in panchromatic spectral band of 450-900nm. The performed cal/val method is the reflectance-based of vicarious calibration methods. We collected ground-based and meteology data such as temperature, surface pressure and reflectance of targets, and radiosonde data used only to test in Goheung. Data collected on each field served as input to radiative transfer codes to generate a top-of-atmosphere(TOA) radiance estimate. Derived TOA is compared with DN of overpass satellite to calculate calibration coefficient of gain and offset.

KARI has prepared Calibration and Validation activities for the KOMPSAT-2 (KOrea Multi-Purpose SATellite-2) MSC data that will be launched at the end of this year. Firstly, we divided the Cal/Val activities of it to four parts, Spatial, Spectral, Radiometric and Geometric, and defmed the detailed Cal/Val items from them. Secondly, Cal/Val targets have been defined and manufactured for the role of them. Thirdly, we have made the plan and the procedure for the Cal/Val items, developed the codes for them, studied more detailed method to do them, and trained the Cal/Val activities using the foreign satellite image data by ourselves. KARI has been now setting up the KOMPSAT-2 LEOP plan with the Cal/Val activities, and probably will finish the EOP Cal/Val activities for the KOMPSAT-2 MSC data by the next April or May.

Ministry of Science & Technology (MOST) and Korea Aerospace Research Institute (KARI) are preparing for the first Korean astronaut program based on the mid and long-term basic plan for space development of Korea from the year of 2003. KARI is making plans for the Korean astronaut's missions with Russia. To participate in the International Space Station (ISS) utilization through the Korean astronaut program, KARI investigates a lot of manned space missions. Among the suggested items, Earth observation on the Russian Module of ISS is the one expected mission for a Korean astronaut. This paper is intended to give readers a brief introduction of ISS Russian Module and research fields of Earth observation for astronaut's mission.

Remote sensing through atmospheric turbulence had been hard works for a long time, because wavefront distortion due to the Earth's atmospheric turbulence deteriorates image quality. But due to the appearance of adaptive optics, it is no longer difficult things. Adaptive optics is the technology to correct random optical wavefront distortions in real time. For past three decades, research on adaptive optics has been performed actively. Currently, most of newly built telescopes have adaptive optical systems. Adaptive optical system is typically composed of three parts, wavefront sensing, wavefront correction and control. In this work, the wavefront sensing technology for adaptive optical system is treated. More specifically, shearing interferometers and Shack-Hartmann wavefront sensors are considered. Both of them are zonal wavefront sensors and measure the slope of a wavefront. . In this study, the shearing interferometer is made up of four right-angle prisms, whose relative sliding motions provide the lateral shearing and phase shifts necessary for wavefront measurement. Further, a special phase-measuring least-squares algorithm is adopted to compensate for the phase-shifting error caused by the variation in the thickness of the index-matching oil between the prisms. Shack-Hartmann wavefront sensors are widely used in adaptive optics for wavefront sensing. It uses an array of identical positive lenslets. And each lenslet acts as a subaperture and produces spot image. Distortion of an input wavefront changes the location of spot image. And the slope of a wavefront is obtained by measuring this relative deviation of spot image. Structures and measuring algorithms of each sensor will be presented. Also, the results of wavefront measurement will be given. Using these wavefront sensing technology, an adaptive optical system will be built in the future.

An electro-optical camera system consists of many subsystems such as the optics, the detector, and the electronics and so on. They may create variations in the processed image that were not present original scene. The performance analysis of the electro-optical camera system is a mathematical construct that provides an optimum design through appropriate trade off analysis. The SNR(Signal to Noise Ratio) is one of the most important performance for the electro-optical camera system. The SNR analysis shown in this paper is performed based on the practical high resolution satellite camera design. For the purpose of the practical camera design, the analysis assumes that the defined radiance, which is calculated for the Korean peninsula, reached directly to the telescope entrance. In addition, the actual operation concept such as integration time and the normal operation altitude is assumed. This paper compares the SNR analysis results according to the various camera characteristics such as the optics, the detector, and the camera electronics. In detail, the optical characteristics can be split into the focal length, F#, transmittance, and so on. And the system responsivity, the quantum efficiency, the TDI stages, the quantization noise and the analogue noise can be used for the detector and the camera electronics characteristics. Finally this paper suggests the optimum design to apply the practical electro-optical system.

In the development of a electronic system for a optical payload comprising mainly EOS(Electro-Optical Sub-system) and PDTS(Payload Data Transmission Sub-system), many aspects should be investigated and discussed for the easy implementation, for th e higher reliability of operation and for the effective ness in cost, size and weight as well as for the secure interface with components of a satellite bus, etc. As important aspects the interfaces between a satellite bus and a payload, and some design features of the CEU(Camera Electronics Unit) inside the payload are described in this paper. Interfaces between a satellite bus and a payload depend considerably on whether t he payload carries the PMU(Payload Management Un it), which functions as main controller of the Payload, or not. With the PMU inside the payload, EOS and PDTS control is performed through the PMU keep ing the least interfaces of control signals and primary power lines, while the EOS and PDTS control is performed directly by the satellite bus components using relatively many control signals when no PMU exists inside the payload. For the CEU design the output channel configurations of panchromatic and multi-spectral bands including the video image data inter face between EOS and PDTS are described conceptually. The timing information control which is also important and necessary to interpret the received image data is described.

This paper introduces an Interactive Feature Extraction (!FE) approach for the registration of satellite imagery by matching extracted point and line features. !FE method contains both point extraction by cross-correlation matching of singular points and line extraction by Hough transform. The purpose of this study is to minimize user's intervention in feature extraction and easily apply the extracted features for image registration. Experiments with these imagery dataset proved the feasibility and the efficiency of the suggested method.

The COMS(Communication, Ocean and Meteorological Satellite), a multi-mission geo-stationary satellite, is being developed by KARl. The first mission of the COMS is the meteorological image and data gathering for weather forecast by using a five channel meteorological imager. The second mission is the oceanographic image and data gathering for marine environment monitoring around Korean Peninsula by using an eight channel Geostationary Ocean Color Imager(GOCI). The third mission is newly developed Ka-Band communication payload certification test in space by providing communication service in Korean Peninsula and Manjurian area. There were many low Earth orbit satellites for ocean monitoring. However, there has never been any geostationary satellite for ocean monitoring. The COMS is going to be the first satellite for ocean monitoring mission on the geo-stationary orbit. The meteorological image and data obtained by the COMS will be distributed to end users in Asia-Pacific area and it will contribute to the improved weather forecast.

In this paper we present a detail approach of the determination of IFOV (Instantaneous Field of View) of high-resolution (l m) panchromatic satellite image over test site. IFOV is the representative measurements as the determination of the spatial resolution in remote sensed imaging system. It can be defined as some area on the ground with the particular altitude when the satellite acquires the image at any given time. Especially, spatial resolution of passive sensors primarily depends on their IFOV. The determination of IFOV goes through simple steps of procedure as followings: Firstly, the GSD (Ground Sample Distance) should be computed at each point on the geometrically corrected image. Then, The GSD is converted into the IFOV. So we are going to explain our test procedures and results.

More than 70 percent of terrestrial territory of Korea is mountainous areas where degradation becomes serious year by year due to illegal tombs, expanding golf courses and stone mine development. We elaborate the potential usage of high resolution image for the monitoring of the phenomena. We made the classification of tombs and the statistical radiometric characteristics of graves were identified from this project. The graves could be classified to 4 groups from the field survey. As compared with grouping data after clustering and discriminant analysis, the two results coincided with each other. Object-oriented classification algorithm for feature extraction was theoretically researched in this project. And we did a pilot project, which was performed with mixed methods. That is, the conventional methods such as unsupervised and supervised classification were mixed up with the new method for feature extraction, object-oriented classification method. This methodology showed about $60\%$ classification accuracy for extracting tombs from satellite imagery. The extraction of tombs' geographical coordinates and graves themselves from satellite image was performed in this project. The stone mines and golf courses are extracted by NDVI and GVI. The accuracy of classification was around 89 percent. The location accuracy showed extraction of tombs from one-meter resolution image is cheaper and quicker way than GPS method. Finally we interviewed local government officers and made analyses on the current situation of mountainous area management and potential usage of KOMPSAT-II images. Based on the requirement analysis, we developed software, which is to management and monitoring system for mountainous area for local government.

KAERI (Korea Atomic Energy Research Institute) has been performing the project named PEFP (proton engineering frontier project). PEFP has been performing the project of a high power proton accelerator. Control system for 20 MeV proton accelerating structure has developed. We use the EPICS(Experimental Physics and Industrial Control System) tool kit as a foundation of the control system. EPICS is adopted for control systems which have OPI(OPerator Interface) and IOqlnput Output Controller). We have performed the PEPF control system on SUN workstation host computer. In this paper, we present the vacuum monitor, RFQ, and DTL Turbo pump control system.

Recently, the need for LBS (Location Based Services) is increasing with the rapid growth of the location measurement units, mobile devices, and communication technologies. Especially, wireless carriers are concentrating on LBS since it is regarded as so-called 'killer application' among wireless data services. Although LBS give us convenience and useful information, its use also raises privacy issues. There are quite possibilities that the people's locations are tracked by location measurement units while people do not recognize the existence of the units. To protect a person's location information, lawful and technical aspects should be considered. In this paper, we explain issues, regulations, standards, and platforms related to the protection of the location information. Finally, we suggest the architecture of a platform complying with the regulations and standards. It considers various issues not covered in other studies.

The Geography Markup Language (GML) is an XML encoding for the transport and storage of geographic information, including both the geometry and properties of geographic features. This paper uses the GML to provide extendibility and interoperability of spatial data in moving objects management system. Since the purpose of the system is to provide locations of the moving objects in the web and mobile environments, we used the GML both for presenting map data and trajectories of the moving objects. The proposed system is composed of Location Data Interface, Moving Objects Engine, and Web/Mobile Presentation Interface. We utilized the concept of Web Map Server, that is web mapping technology of OGC (Open Geospatial Consortium), to integrate map data and the location information of the moving objects. In the process of the integration, we used the standard data model and interfaces while defining new application schema. Since our suggested system uses open spatial data encoding and interfaces, both extendibility and interoperability are guaranteed.

Ground control points(GCPs) can be extracted from SAR data given precise orbit for DTM generation using optic images and other SAR data. In this study, we extract GCPs from ERS SAR data and SRTM DEM. Although it is very difficult to identify GCPs in ERS SAR image, the geometry of optic image and other SAR data are able to be corrected and more precise DTM can be constructed from stereo optic images. Twenty GCPs were obtained from the ERS SAR data with precise Delft orbit information. After the correction was applied, the mean values of planimetric distance errors of the GCPs were 3.7m, 12.1 and -0.8m with standard deviations of 19.9m, 18.1, and 7.8m in geocentric X, Y, and Z coordinates, respectively. The geometries of SPOT stereo pair were corrected by 13 GCPs, and r.m.s. errors were 405m, 705m and 8.6m in northing, easting and height direction, respectively. And the geometries of RADARS AT stereo pair were corrected by 12 GCPs, and r.m.s. errors were 804m, 7.9m and 6.9m in northing, easting and height direction, respectively. DTMs, through a method of area based matching with pyramid images, were generated by SPOT stereo images and RADARS AT stereo images. Comparison between points of the obtained DTMs and points estimated from a national 1 :5,000 digital map was performed. For DTM by SPOT stereo images, the mean values of distance errors in northing, easting and height direction were respectively -7.6m, 9.6m and -3.1m with standard deviations of 9.1m, 12.0m and 9.1m. For DTM by RADARSAT stereo images, the mean values of distance errors in northing, easting and height direction were respectively -7.6m, 9.6m and -3.1m with standard deviations of 9.1m, 12.0m and 9.1m. These results met the accuracy of DTED level 2

Atmospheric correction over the ocean part is more important than that over the land because the signal from the ocean is very small about one tenth of that reflected from land. In this study, the Spectral Shape Matching Method (SSMM) developed by Ahn and Shanmugam (2004) is evaluated using Landsat imagery acquired over the highly turbid Saemangeum Coastal Area. The result of SSMM is compared with COST model developed by Chavez (1991 and 1997). In principle, SSMM is simple and easy to implement on any satellite imagery, relying on both field and image properties. To assess the potential use of these methods, several field campaigns were conducted in the Saemangeum coastal area corresponding with Landsat-7 satellite's overpass on 29 May 2005. In-situ data collected from the coastal waters of Saemangeum using optical instruments (ASD field spectroradiometer) consists of ChI, Ap, SS, aooM, F(d). In order to perform SSMM, we use the in-situ water-leaving radiance spectra from clear oceanic waters to estimate the the path radiance from total signal recorded at the top of the atmosphere (TOA), due to the reason that the shape of clear water-leaving radiance spectra is nearly stable than turbid water-leaving radiance spectra. The retrieved water-leaving radiance after subtraction of path signal from TOA signal in this way is compared with that estimated by COST model. The result shows that SSMM enabled retrieval of water-leaving radiance spectra that are consistent with in-situ data obtained from Saemangeum coastal waters. The COST model yielded significantly high errors in these areas.

This study proposes a fuzzy classification using EM algorithm. For cluster validation, this approach iteratively estimates the class-parameters in the fuzzy training for the sample classes and continuously computes the log-likelihood ratio of two consecutive class-numbers. The maximum ratio rule is applied to determine the optimal number of classes.

IETF suggested AAA for safe and reliable user authentication on various network and protocol caused by development in internet and increase in users. Diameter standard authentication system does not provide mutual authentication and non-repudiation. AAA authentication system using public key was suggested to supplement such Diameter authentication but application in mobile service control nodes is difficult due to overhead of communication and arithmetic. ID based AAA authentication system was suggested to overcome such weak point but it still has the weak point against collusion attack or forgery attack. In this thesis, new ID based AAA authentication system is suggested which is safe against collusion attack and forgery attack and reduces arithmetic quantity of mobile nodes with insufficient arithmetic and power performance. In this thesis, cryptological safety and arithmetical efficiency is tested to test the suggested system through comparison and assessment of current systems. Suggested system uses two random numbers to provide stability at authentication of mobile nodes. Also, in terms of power, it provides the advantage of seamless service by reducing authentication executing time by the performance of server through improving efficiency with reduced arithmetic at nodes.

This study addresses a photogrammetric approach to generate Mars topographic products from mapping data of Mars Global Surveyor (MGS). High-resolution stereo images and laser altimetry data collected from the MGS mission are combined and processed to produce Digital Elevation Models (DEM) and orthoimages. First, altimeter data is registered to high resolution images and considerable registration offset (around 325 m) is discovered on high resolution stereo images. Altimetry data, exterior orientation elements of the camera and conjugate points are used for bundle adjustment to solve this mis-registration and detennine the ground coordinates. The mis-registration of altimetry data are effectively eliminated after the bundle adjustment. Using the adjusted exterior orientation the ground coordinates of conjugate points are detennined. A sufficient number of corresponding points collected through image matching and their precise 3-D ground coordinates are used to generate DEM and orthoimages. A posteriori standard deviations of ground points after bundle adjustment indicate the accuracy of OEM generated in this study. This paper addresses the photogrammetric procedure: the registration of altimetry data to stereo pair images, the bundle adjustment and the evaluation, and the generation of OEM and orthoimages.

Recently there have been a lot of kinds of damages in forest area such as forest fires, forest pest, landslide so that the efficient methods to mange those information and the way to face them are deadly needed. In this study, there were preparing the various vegetation index map and comparing them with the field surveying the tried to figure out which vegetation index algorism is the best proper to present forest fire damaged area. These all were based on Landsat ETM+ satellite image (2000.10.16). The result of this study is to select the high correlation algorism among the various vegetation indexes and then construct the forest fire disaster map, the case of forest fires damaged area.

The prototype of the radiometric calibration algorithm, including the correction of scan mirror's angle, has been developed for the stationary meteorological sensor, firstly in Korea. We use this system on GOES-12 to evaluate two coefficients, slope and intercept. The evaluated coefficients show good agreement with the NESDIS's results for the five-case data. The calculated coefficients have been applied to the conversion from the measured counts to the radiance and the converting methods according to the scanning are investigated to enhance the radiometric accuracy.

A conceptual study about the angle information based orbit determination technique for a geostationary satellite was performed. With an assumption that the simultaneous observing of the earth and nearby stars is possible, we confirmed that the view angles between the earth and stars can be use as inputs for orbit determination process. By the MA TLAB simulation with least square method, the convergence is confirmed. This conceptual study was performed with the COMS for instance. This technique will be able to use as a back-up of ground station's orbit determination or a part of autonomous satellite operation.

This paper examines that is extracted certain information in forest areas within high resolution imagery based on wavelet transformation. First of all, study areas are selected one more species distributed spots refer to forest type map. Next, study area is cut 256 x 256 pixels size because of image processing problem in large volume data. Prior to wavelet transformation, five texture parameters (contrast, dissimilarity, entropy, homogeneity, Angular Second Moment (ASM≫ calculated by using Gray Level Co-occurrence Matrix (GLCM). Five texture images are set that shifting window size is 3x3, distance .is 1 pixel, and angle is 45 degrees used. Wavelet function is selected Daubechies 4 wavelet basis functions. Result is summarized 3 points; First, Wavelet transformation images derived from contrast, dissimilarity (texture parameters) have on effect on edge elements detection and will have probability used forest road detection. Second, Wavelet fusion images derived from texture parameters and original image can apply to forest area classification because of clustering in Homogeneous forest type structure. Third, for grading evaluation in forest fire damaged area, if data fusion of established classification method, GLCM texture extraction concept and wavelet transformation technique effectively applied forest areas (also other areas), will obtain high accuracy result.

Mobile Mapping Systems using the vehicle equipped the GPS, IMU, CCD Cameras is the effective system for the management of the road facilities, update of the digital map, and etc. They must provide users with the sensor data which is acquired by Mobile Mapping Systems in real-time so that users can process what they want by using the latest data. But it' s not an easy process because the amount of sensor data is very large, particularly image data to be transmitted. So it is necessary to reduce the amount of image data so that it is transmitted effectively. In this study, the effective method was suggested for the compression/decompression image data using the Wavelet Transformation and Huffman Coding. This technique will be possible to transmit of the geographic information effectively such as position data, attitude data, and image data acquired by Mobile Mapping Systems in the wireless internet environment when data is transmitted in real-time.

Ground processing for geostationary weather satellite such as GOES, MTSAT includes the process called image navigation. Image navigation means the retrieval of satellite navigational parameters from images and requires landmark detection by matching satellite images against landmark chips. For an automated preprocessing, a matching must be performed automatically. However, if match results contain errors, the accuracy of image navigation deteriorates. To overcome this problem, we propose the use of a robust estimation technique, called Random Sample Consensus (RANSAC), to automatically detect mismatches. We tested GOES-9 satellite images with 30 landmark chips. Landmark chips were extracted from the world shoreline database. To them, matching was applied and mismatch results were detected automatically by RANSAC. Results showed that all mismatches were detected correctly by RANSAC with a threshold value of 2.5 pixels.

In this paper, in order to identify and recognize attack patterns, we propose a Bayesian classification using frequent patterns. In theory, Bayesian classifiers guarantee the minimum error rate compared to all other classifiers. However, in practice this is not always the case owing to inaccuracies in the unrealistic assumption{ class conditional independence) made for its use. Our method addresses the problem of attribute dependence by discovering frequent patterns. It generates frequent patterns using an efficient FP-growth approach. Since the volume of patterns produced can be large, we propose a pruning technique for selection only interesting patterns. Also, this method estimates the probability of a new case using different product approximations, where each product approximation assumes different independence of the attributes. Our experiments show that the proposed classifier achieves higher accuracy and is more efficient than other classifiers.

Recently as large sized urban development and the city ward drifting of population are caused, the urban surface temperature is raised very seriously and rapidly. These artificial developments have destroyed the inner and outer landscapes such as topography and have changed complex local climate such as a sudden rise in temperature, the change of wind field and air pollution. In order to clarify this problem visually, the studies on extracting the thermal infrared and the characteristic analysis of local climate in urban area had been performed by using the sixth band of Landsat TM and ETM+. However, there is a need to alternate Landsat TM and ETM+ because these satellite images are not applied any more. Therefore, in this paper it is proposed to use 2 Aster image (2004.4.17 daily 2b03, 2004.10.10 night 2b03) of EOS AM and to extract the surface temperature. Also, the pattern of surface temperature in urban area and the application possibility in local climate study are proposed by verifying the correlation with A WS data. Also, IKONOS image was used to figure out the artificial development area in visual.

In this study the spatial distribution characters of forest in forest damaged area were first considered by analyzing spatial data and monitoring forest landscape. Then suitable tree species on each site were selected through the weighted score analysis of GIS analysis methods. Finally, the best forest stand arrangement method could be presented on the 3D based simulation system for the advanced reforestation technology in Korea. For this purpose, the virtual reforestation system was implemented by using the concept of virtual GIS and CBD (Component Based Development) method. By use of this system the change offorest landscape of burnt forest area some years after reforestation practice could be detected and monitored by applying the site index and 3D modeling method.

The scattering problem of the randomly rough surface is examined by the method of moments(MoM), small perturbation method (SPM), integral equation method (IEM) and the semi-empirical polarimetic model. To apply the numerical technique of the MoM to microwave scattering from a rough surface, at first, many independent randomly rough surfaces with a rms height and a correlation length are generated with Gaussian random deviate. Then, an efficient Monte Carlo simulation technique is applied to estimate the scattering coefficients of the surfaces.

This paper describes a time-spatial domain model for simulating raw data acquisition of space-borne SAR system. The position, velocity and attitude information of the platform at a certain time instance is used for deriving sensor-target model. Ground target is modelled by a set of point scatters with reflectivity and two-dimensional ground coordinates. The signal received by SAR is calculated for each slow and fast time instance by integrating the reflectivity and phase values from all target point scatters. Different from frequency domain simulation algorithms, the proposed time domain algorithm can provide fully physical modelling of SAR raw data simulation without any assumptions or approximations.

This paper presents the design of two antennas for the Dual-channel Radiometers for Earth and Atmosphere Monitoring (DREAM) the main payload, will be launched at NARO space center in Korea in 2007. The antennas are designed to meet stringent requirements of a very high beam efficiency, good pattern symmetry, and low VSWR, at 23.8 GHz and 37 GHz bands. Corrugated horn antennas are used. The simulation results of the electrical performance are presented.

Soil moisture, through its dominance in the exchange of energy and moisture between the land and atmosphere, plays a crucial role in influencing atmospheric circulation. To identify the crucial role, it is a common agreement that knowledge of land surface processes and development of remote sensing techniques are of great important scientific issues. This research uses TRMM satellite C band (10.65 GHz) data to retrieve soil moisture on the Tibetan Plateau in Mainland China. Two retrieval schemes that are implemented include the t-(J) model and the R model. The latter one is developed based on a land surface process and radiobrightness (R) model for bare soil and vegetated terrain. Compared with the in situ ground measurements, the soil moisture retrieved from the R model and the t-(J) model with vegetation information obviously appear more accurate than that derived from bare soil model. Retrieved soil moisture contents from the two inversion models, R model and t-(J) model, have a similar trend, but the former appears to be superior in terms of correlation coefficient and bias compared with in situ data. In the future, we will apply the R model with the TRMM 10.65 GHz brightness temperature to monitor long-term soil moisture variation over Tibet Plateau.

A numerical scattering model for artificial metal structure based on physical optics approximation is developed to identify the height of phase center, and the result is compared with interferometric SAR DEM. The interferometric SAR data were gathered by AIRSAR during PACRIM- II campaign on Jeju Island. Power transmission towers on piedmont pasture along the slopes of Mt. Halla look like elliptic risings in TOPSAR DEM. The heights of risings are quantitatively analyzed using a scattering model in the way of achieving the height of phase centers of power transmission towers. A numerical algorithm is developed on the basis of physical optics approximation. The structure of power transmission tower was decomposed into hundreds of rectangular metal plates, of which the scattering matrix is known in analytic form, and the calculated scattering fields were summed coherently. The effect of direct backscattering component, ground-scatterer component and scatterer-ground component are decomposed and computed individually for each rectangular metal plate. The $\Deltak-radar$ equivalent was used to calculate height of phase center of the scatterer. The heights of a selected power transmission tower and scattering algorithm results give existence and location of the transmission towers but not actual tower heights.

These days, vehicle is evolving from the isolated space of transportation to the third digital life space connected to the information world via wired and wireless internet and in which the various activities are possible. According to this trend, the speed of growth in the development of Telematics technology and standard is being accelerated due to the government's IT839 strategy and market needs in Korea. ETRI, TTA, and the Telematics Standardization Forum play key role in developing domestic Telematics standard of core technology needed by industry in relation with each other. The international standards are mainly developed by de-facto standardization organizations such as OSGi, OMA, ERTICO, etc. currently. In this paper, we discuss the trends and issues in Telematics standardization and future strategy.

In this paper, we introduce an Intersection Collision Avoidance (ICA) system as a convergence example of Telematics and USN technology and show several requirements for the ICA system. Also, we propose a system design that satisfies the requirements of reliable vehicular data acquisition, real-time data transmission, and effective intersection collision prediction. The ICA system consists of vehicles, sensor nodes and a base station that can provide drivers with a reliable ICA service. Then, we propose several technological solutions needed when implementing the ICA system. Those are about sensor nodes deployment, vehicular information transmission, vehicular location data acquisition, and intersection collision prediction methods. We expect this system will be a good case study applied to real Telematics application based on USN technology.

This study attempts at building an integrated GIS computing framework for evaluating space-time accessibility of an individual with the approach of time geography model. The proposed method is based on the integration of mobile GIS and object-relational spatio-temporal database. Three components are central to our system: ( i ) mobile GIS application that transmits spatio-temporal trajectory data of an individual; ( ii ) spatio-temporal database server that incorporates the time geography model; and (iii) geovisualization client that provides time geographic queries to the spatio-temporal database. As for the mobile GIS application, spatio-temporal trajectory data collected by GPS-PDA client is automatically transmitted to the database server through mobile data management middleware. The spatio-temporal database server implemented by extending a generic DBMS provides spatio-temporal objects, functions and query languages. The geovisualization client illustrates 3D visual results of the queries about space-time path. space-time prism and space-time accessibility. This study shows a method of integrating mobile GIS and DBMS for time geography application, and presents an appropriate spatio-temporal data model for evaluating space-time accessibility of an individual.

Recently, Intelligent Transportation System(ITS) has been applied to satisfy increasing traffic demand every year and to solve many traffic problems. Especially, Advanced Traveller Information System(ATIS) is a transportation system to optimize the trip of each other vehicle. It is important to provide the driver with quick and comfortable path from source to destination. However, it is difficult to provide a shortest path in a road network with dynamic cost. Because the existing research has a static cost. Therefore, in this paper we propose an operator for searching traffic dependent shortest path. The proposed operator finds the shortest path from source to destination using a current time cost and a difference cost of past time cost. Such a method can be applied to the road status with time. Also, we can expect a predicted arrival time as well as the shortest path from source to destination. It can be applied to efficiently application service as ITS and have the advantages of using the road efficiently, reducing the distribution cost, preparing an emergency quickly, reducing the trip time, and reducing an environmental pollution owing to the saving the fuel.

In the area of remote sensing, an immense number of images are continuously generated by various remote sensing systems. These images must then be managed by a database system efficient storage and retrieval. There are many types of image database systems, among which the content-based image retrieval (CBIR) system is the most advanced. CBIR utilizes the metadata of images including the feature data for indexing and searching images. Therefore, the performance of image retrieval is significantly affected by the storage method of the image metadata. There are many features of images such as color, texture, and shape. We mainly consider the shape feature because shape can be identified in any remote sensing while color does not always necessarily appear in some remote sensing. In this paper, we propose a metadata representation and storage method for image search based on shape features. First, we extend MPEG-7 to describe the shape features which are not defined in the MPEG-7 standard. Second, we design a storage schema for storing images and their metadata in a relational database system. Then, we propose an efficient storage method for managing the shape feature data using a Wavelet technique. Finally, we provide the performance results of our proposed storage method.

In a ubiquitous environment made up of multiple sensors, most sensors participate in communications with limited battery, and the sensor node isn't able to participate in communications when all the battery is used up. When an existing authentication method is used for the sensor node which has to participate in a long term communication with limited battery, it creates a problem by making the length of network maintenance or sensor node's operation time relatively shorte. Therefore, a network structure where RM (Register Manager) node and AM (Authentication Manager) node are imported to solve the energy consumption problem during a communication process is presented in this thesis. This offers a low power protocol based on safety through a mutual authentication during communications. Through registration and authentication manager nodes, each sensor nodes are ensured of safety and the algorithm of key's generation, encryption/descramble and authentication is processed with faster operation speed. So the amount of electricity used up during the communications between sensor nodes has been evaluated. In case of the amount of electrical usage, an average of $34.783\%$ for the same subnet and 36.855 for communications with two different subnets, are reduced. The proposed method is a protocol which maintains the limited battery for a long time to increase the effectiveness of energy usage in sensor nodes and can also increase the participation rate of communication by sensor nodes.

In most biological laboratory, sequences from sequence machine are stored into file disks as simple files. It will be hard work to store and manage the sequence data with consistency and integrity such as storing redundant files. It is required needed to develop a system which integrated and managed genome data with consistency and integrity for accurate sequence analysis. There fore, in this paper, we not only store gene and protein sequence data through sequencing but also manage them. We also make a integrate schema for transforming the file formats and design database system using it. As integrated schema is designed as a BSML, it is possible to apply a style language of XSL. From this, we can transfer among heterogeneous sequence formats.

Dengue Fever(DF) and Dengue haemorrhagic fever(DHF) has become a major international public health concern. Dengue Fever(DF) and Dengue haemorrhagic Fever (DHF) is also still the major health problem of Thailand, although many campaigns against it have been conducted throughout the country. GIS and Remotely Sensed data are used to evaluate the relationships between socio-spatial, environmental factors/indicators and the incidences of viral diseases. The aim of the study is to identify the spatial risk factors in Dengue and Dengue Haemorrhagic Fever in Sukhothai province, Thailand using statistical, spatial and GIS Modelling. Preliminary results demonstrated that physical factors derived from remotely sensed data could indicate variation in physical risk factors affecting DF and DHF. The present study emphasizes the potential of remotely sensed data and GIS in spatial factors affecting Dengue Risk Zone analysis. The relationship between land cover and the cases of incidence of DF and DHF by information value method revaluated that highest information value is obtained for Built-up area. A negative relationship was observed for the forest area. The relations between climate data and cases of incidence have shown high correlation with rainfall factors in rainy season but poor correlation with temperature and relative humidity. The present study explores the potential of remotely sensed data and GIS in spatial analysis of factors affecting Dengue epidemic, strong spatial analysis tools of GIS. The capabilities of GIS for analyst spatial factors influencing risk zone has made it possible to apply spatial statistical analysis in Disease risk zone.

Miniaturization of computing devices, and advances in wireless communication and positioning systems will create a wide and increasing range of database applications such as location-based services, tracking and transportation systems that has to deal with Moving Objects. Various types of queries could be posted to moving objects, including past, present and future queries. The key problem is how to model the location of moving objects and enable Database Management System (DBMS) to predict the future location of a moving object. It is obvious that there is a need for an innovative, generic, conceptually clean and application-independent approach for spatio-temporal handling data. This paper presents behavioral aspect of the spatio-temporal databases for managing and querying moving objects. Our objective is to impelement and extend the Spatial TAU (STAU) system developed by Dr.Pelekis that provides spatio-temporal functionality to an Object-Relational Database Management System to support modeling and querying moving objecs. The results of the impelementation are demonstrated in this paper.

We design as well as implement MRTG++ enhanced by eliminating drawbacks of original MRTG. Existing MRTG makes it easy to monitor network resources on the web, and it can show some trend utilization about resources of remote systems. However MRTG has only functions showing statistical information data with daily/monthly/yearly characteristics in real-time, and periodically deletes stored data. Thus we improve log file-based storing method as an effectivelly storing method with database, propose expended MRTG++ retrieving as well as managing with measured data. It also can be applied in ubiquitous environment.