DOI QR코드

DOI QR Code

Numerical Study on using Immersion Cooling for Thermal Management of ESS (Energy Storage System)

ESS(Energy Storage System) 열관리를 위한 액침 냉각 활용에 대한 수치해석 연구

  • Jeonggyun Ham (Department of Mechanical Engineering, Chosun University) ;
  • Nayoung You (Department of Mechanical Engineering, Chosun University) ;
  • Myeongjae Shin (Department of Mechanical Engineering, Chosun University) ;
  • Honghyun Cho (Department of Mechanical Engineering, Chosun University)
  • 함정균 (조선대학교 기계공학과) ;
  • 유나영 (조선대학교 기계공학과) ;
  • 신명재 (조선대학교 기계공학과) ;
  • 조홍현 (조선대학교 기계공학과)
  • Received : 2024.05.10
  • Accepted : 2024.05.30
  • Published : 2024.06.01

Abstract

The introduction of the sector coupling concept has expanded the scope of ESS utilization, resulting in the importance of thermal management of ESS. To ensure the safe use of the lithium-ion batteries that are used in ESS, it is important to use the batteries at the optimal temperature. To examine the utilization of liquid cooling in ESS, numerical study was conducted on the thermal characteristics of 21700 battery modules (16S2P array) during liquid cooling using Novec-649 as insulating fluid. The NTGK model, an MSMD model in ANSYS fluent, was used to investigate thermal characteristics on the battery modules with liquid immersion cooling. The results show that the final temperature of the battery module discharged at 5 C-rate is 68.9℃ using natural convection and 48.3℃ using liquid cooling. However, the temperature difference among cells in the battery module was up to 0.5℃ when using natural convection cooling and 5.8℃ when using liquid cooling, respectively, indicating that the temperature difference among cells was significantly increased when liquid cooling was used. As the mass flow rate increased from 0.01 kg/s to 0.05 kg/s, the average temperature of the battery module decreased from 48.3℃ to 38.4℃, confirming that increasing the mass flow rate of the insulating fluid improves the performance of liquid immersion cooling. Although partial liquid immersion cooling has a high cooling performance compared to natural convection cooling, the temperature difference between modules was up to 8.9℃, indicating that the thermal stress of the battery cells increased.

Keywords

Acknowledgement

본 과제(결과물)는 2024년도 교육부의 재원으로 한국연구재단의 지원을 받아 수행된 지자체-대학 협력기반 지역혁신 사업의 결과입니다(과제관리번호: 2021RIS-002).

References

  1. Hassan, A., Ilyas, S. Z., Jalil, A., and Ullah, Z., 2021, Monetization of the environmental damage caused by fossil fuels, Environmental Science and Pollution Research, Vol. 28, pp. 21204-21211.
  2. Deshmukh, M., Sameeroddin, M., Abdul, D., and Sattar, M., 2023, Renewable energy in the 21st century: A review, Materials Today: Proceedings, Vol. 80, pp. 1756-1759.
  3. Parthiban, R., and Ponnambalam, P., 2022, An enhancement of the solar panel efficiency: a comprehensive review, Frontiers in Energy Research, Vol. 10, pp. 937155.
  4. Hand, B., and Cashman, A. 2020, A review on the historical development of the lift-type vertical axis wind turbine: From onshore to offshore floating application, Sustainable Energy Technologies and Assessments, Vol. 38, pp. 100646.
  5. Zhang, X., 2021, Numerical study of geothermal district heating from a ground heat exchanger coupled with a heat pump system, Applied Thermal Engineering, Vol. 185, pp. 116335.
  6. Choi, C., 2024, 에너지 섹터커플링 기술을 활용한 P2X 유연자원화 기술, The Korean Institute of Electrical Engineers, Vol. 73, No. 1, pp. 13-14.
  7. Yi, Y., Zhou, Y., Su, H., Fang, C., Wang, H., Feng, D., and Li, H., 2023, Overview of EV battery testing and evaluation of EES systems located in EV charging station with PV, Energy Reports, Vol. 9, pp. 134-144.
  8. Ji, H., Luo, T., Dai, L., He, Z., and Wang, Q., 2023, Topology design of cold plates for pouch battery thermal management considering heat distribution characteristics, Applied Thermal Engineering, Vol. 224, pp. 119940.
  9. Zang, F., Liu, P., He, Y., and Li, S., 2022, Cooling performance optimization of air cooling lithium-ion battery thermal management system based on multiple secondary outlets and baffle, Journal of Energy Storage, Vol. 52, pp. 104678.
  10. Amosedinakaran, S., Kannan, R., Kannan, S., Ramkumar, A., Suresh, S., and Bhuvanes, A., 2024, Performance Analysis for Battery Stability Improvement using Direct Air Cooling Mechanism for Electric Vehicles, Advances in Electrical Engineering, Electronics and Energy, pp. 100585.
  11. Liu, X., Zhang, T., Gao, Q., Han, Z., Huang, H., Xu, Y., Chen, H., and Xu, X., 2024, The suppression of thermal propagation using spray cooling with R410A in overheated lithium battery pack, Case Studies in Thermal Engineering, Vol. 58, pp. 104339.
  12. Alghamdi, H.,. Farhan, M., Rosdi, M., Mukhtar, A., Yasir, A., and Alviz-Meza, A., 2023, Controlling thermal runaway by simultaneous use of thermoelectric module and phase change material in the lithium-ion batteries of electric vehicles, Case Studies in Thermal Engineering, Vol. 52, pp. 103697.
  13. Alghassab, M., 2024, Investigating the performance improvement of lithium-ion battery cooling process using copper fins and phase change materials (PCMs), Case Studies in Thermal Engineering, Vol. 59, pp. 104473.
  14. Choi, H., Lee, H., Kim, J., and Lee, H., 2023, Hybrid single-phase immersion cooling structure for battery thermal management under fast-charging conditions, Energy Conversion and Management, Vol. 287, pp. 117053.
  15. Liu, Q., Liu, Y., Zhang, M., Wang, S., Li, W., Zhu, X., Ju, X., Xu., C., and Wei, B. 2024, Comprehensive investigation of the electro-thermal performance and heat transfer mechanism of battery system under forced flow immersion cooling, Energy, Vol. 298, pp. 131404
  16. Williams, N. P., Trimble, D., and O'Shaughnessy, S. M. 2024, An experimental investigation of liquid immersion cooling of a four cell lithium-ion battery module, Journal of Energy Storage, Vol. 86, pp. 111289.
  17. Kim, M., Ham, J., Shin, D., and Cho, H., 2022, Comparison of Cooling Performance in a Cylindrical Battery with Single-Phase Direct Contact Cooling under Various Operating Conditions, Batteries, Vol. 8, No. 10, pp. 195.
  18. Matsson, J., 2022, An Introduction to ANSYS Fluent 2022, Sdc Publications.