Geomechanics and Engineering

  • 제37권6호
  • /
  • Pages.599-614
  • /
  • 2024
  • /
  • 2005-307X(pISSN)
  • /
  • 2092-6219(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Theoretical analysis of erosion degradation and safety assessment of submarine shield tunnel segment based on ion erosion

  • Xiaohan Zhou (School of Civil Engineering, Chongqing University) ;
  • Yangyang Yang (School of Civil Engineering, Chongqing University) ;
  • Zhongping Yang (School of Civil Engineering, Chongqing University) ;
  • Sijin Liu (China Railway 14th Bureau Group Co., Ltd.) ;
  • Hao Wang (School of Civil Engineering, Chongqing University) ;
  • Weifeng Zhou (School of Civil Engineering, Chongqing University)
  • 투고 : 2023.12.29
  • 심사 : 2024.06.04
  • 발행 : 2024.06.25
⟨ 이전 논문 다음 논문 ⟩

초록

To evaluate the safety status of deteriorated segments in a submarine shield tunnel during its service life, a seepage model was established based on a cross-sea shield tunnel project. This model was used to study the migration patterns of erosive ions within the shield segments. Based on these laws, the degree of deterioration of the segments was determined. Using the derived analytical solution, the internal forces within the segments were calculated. Lastly, by applying the formula for calculating safety factors, the variation trends in the safety factors of segments with different degrees of deterioration were obtained. The findings demonstrate that corrosive seawater presents the evolution characteristics of continuous seepage from the outside to the inside of the tunnel. The nearby seepage field shows locally concentrated characteristics when there is leakage at the joint, which causes the seepage field's depth and scope to significantly increase. The chlorine ion content decreases gradually with the increase of the distance from the outer surface of the tunnel. The penetration of erosion ions in the segment is facilitated by the presence of water pressure. The ion content of the entire ring segment lining structure is related in the following order: vault < haunch < springing. The difference in the segment's rate of increase in chlorine ion content decreases as service time increases. Based on the analytical solution calculation, the segment's safety factor drops more when the joint leaks than when its intact, and the change rate between the two states exhibits a general downward trend. The safety factor shows a similar change rule at different water depths and continuously decreases at the same segment position as the water depth increases. The three phases of "sudden drop-rise-stability" are represented by a "spoon-shaped" change rule on the safety factor's change curve. The issue of the poor applicability of indicators in earlier studies is resolved by the analytical solution, which only requires determining the loss degree of the segment lining's effective bearing thickness to calculate the safety factor of any cross-section of the shield tunnel. The analytical solution's computation results, however, have some safety margins and are cautious. The process of establishing the evaluation model indicates that the secondary lining made of molded concrete can also have its safety status assessed using the analytical solution. It is very important for the safe operation of the tunnel and the safety of people's property and has a wide range of applications.

키워드

과제정보

This study is supported by the National Natural Science Foundations of China (52374079). The authors gratefully acknowledge these supports.

참고문헌

  1. Batany, S., Peyneau, P.E., Lassabatere, L., Bechet, B., Faure, P. and Dangla, P. (2019), "Interplay between molecular diffusion and advection during solute transport in macroporous media", Vadose Zone J., 18(1), 1-15 https://doi.org/10.2136/vzj2018.07.0140.
  2. Chen, G.H., Zou, J.F. and Qian, Z.H. (2019), "An improved collapse analysis mechanism for the face stability of shield tunnel in layered soils", Geomech. Eng., 17(1), 97-107. https://doi.org/10.12989/gae.2019.17.1.097.
  3. Dong, B.X., Chieh, C.W., Ong, D.E.L. and Ge, L. (2021), "Evaluation of geological conditions and clogging of tunneling using machine learning", Geomech. Eng., 25(1), 59-73. https://doi.org/10.12989/gae.2021.25.1.059.
  4. Dong, L., Yang, Y.K., Liu, Z.X., Yang, T., Xue, C.H., Shao, R.Z. and Wu, C.Q. (2024), "Effect of chloride ion migration behaviour on the microstructure and mechanical properties of ultra-high performance concrete: A review", J. Build. Eng., 82, https://doi.org/10.1016/j.jobe.2023.108233.
  5. Feng, C.Q., Si, X.H., Li, B.T., Cao, L.M. and Zhu, J. (2021), "An inverse problem to simulate the transport of chloride in concrete by time-space fractional diffusion model", Inverse Probl. Sci. Eng., 29(12), 2429-2445. https://doi.org/10.1080/17415977.2021.1914606.
  6. Feng, K., He, C., Qiu, Y., Zhang, L., Wang, W., Xie, H.M., Zhang, Y.Y. and Cao, S.Y. (2018), "Full-scale tests on bending behavior of segmental joints for large underwater shield tunnels", Tunn. Undergr. Sp. Tech., 75, 100-116. https://doi.org/10.1016/j.tust.2018.02.008.
  7. Fu, H., Di, W., Nan, X. and Chen, O.R. (2021), "Upper bound limit analysis of blow-out failure mode of excavation face of shield tunnel considering groundwater seepage", Geomech. Eng., 26(3), 227-234. https://doi.org/10.12989/gae.2021.26.3.227.
  8. Ghasemi, S.H. and Nowak, A.S. (2018), "Reliability analysis of circular tunnel with consideration of the strength limit state", Geomech. Eng., 15(3), 879-888. https://doi.org/10.12989/gae.2018.15.3.879.
  9. Gong, C.J. and Ding, W.Q. (2018), "A computational framework to predict the water-leakage pressure of segmental joints in underwater shield tunnels using an advanced finite element method", Int. J. Number. Anal. Mech. Geomech., 42(16), 1957-1975. https://doi.org/10.1002/nag.2839.
  10. Guo, X.F., Li, C. and Huo, T.H. (2021), "A quantitative evaluation method on the stability of roadway surrounding rock in partial confining stress based on plastic zone shapes", Geomech. Eng., 25(5), 405-415. https://doi.org/10.12989/gae.2021.25.5.405.
  11. He, C. and Feng, K. (2021), "Integral analysis method of large-section shield tunnel structure", Tunnel construction (in English and Chinese), 41(11), 1827-1848, I0021-I0042. https://doi.org/10.3973/j.issn.2096-4498.2021.11.002.
  12. He, Z.S., He, C., Kang, X.Y., Huang, X. and Wang, S.M. (2023), "Assessment of structural performance of super large cross-section subsea RC shield tunnels: Emphasis on the combined effects of highly hydrostatic pressure and corrosion-induced deterioration", Ocean Eng., 288. https://doi.org/10.1016/j.oceaneng.2023.116134.
  13. Hodhod, O.A. and Ahmed, H.I. (2014), "Modeling the service life of slag concrete exposed to chlorides", Ain Shams Eng. J., 5(1),49-54. https://doi.org/10.1016/j.asej.2013.08.001.
  14. Huang, W.M., Wang, J.C., Xu, R.Q., Yang, Z.X. and Xu, R.Q. (2020), "Structural analysis of shield tunnel lining using theory of curved beam resting on elastic foundation", J. Zhejiang Univ., https://doi.org/10.3785/j.issn.1008-973X.2020.04.018.
  15. JTG D70-2004 (2004), Code for Design of Road Tunnel, China communications press, Beijing, China.
  16. JTG/T D70-2010 (2010), Guidelines for Design of Highway Tunnel, China communications press, Beijing, China.
  17. Kim, N.Y., Park, D.H., Jung, H.S. and Kim, M.I. (2020), "Deformation characteristics of tunnel bottom after construction under geological conditions of long-term deformation", Geomech. Eng., 21(2), 171-178. https://doi.org/10.12989/gae.2020.21.2.171.
  18. Lei, M.F., Peng, L.M. and Shi, C.H. (2015), "Durability evaluation and life prediction of shield segment under coupling effect of chloride salt environment and load", J. Central South Univ., 46, 3092-3099. https://doi.org/10.11817/j.issn.1672-7207.2015.08.044.
  19. Liang, X., Qi, T.Y., Jin, Z.Y., Qin, S.J., Chen, P.T. and Liu, Y. (2020), "Risk assessment system based on fuzzy composite evaluation and a backpropagation neural network for a shield tunnel crossing under a river", Adv. Civil Eng., 1-14. https://doi.org/10.1155/2020/8840200.
  20. Liu, B., Yu, Z.W., Hang, Y.H., Wang, Z.L., Yang, S. and Liu, H. (2020), "A simplified combined analytical method for evaluating the effect of deep surface excavations on the shield metro tunnels", Geomech. Eng., 23(5), 405-418. https://doi.org/10.12989/gae.2020.23.5.405.
  21. Liu, J.K., Jiang, Y.J., Zhang, Y.C. and Sakaguchi, O. (2021), "Influence of different combinations of measurement while drilling parameters by artificial neural network on estimation of tunnel support patterns", Geomech. Eng., 25(6), 439-454. https://doi.org/10.12989/gae.2021.25.6.439.
  22. Liu, J.K., Luan, H.G., Zhang, Y.C., Osamu, S. and Jiang, Y.J. (2020), "Prediction of unconfined compressive strength ahead of tunnel face using measurement-while-drilling data based on hybrid genetic algorithm", Geomech. Eng., 22(1), 81-95. https://doi.org/10.12989/gae.2020.22.1.081.
  23. Liu, X.R., Xiong, F., Zhou, X.H., Liu, D.S., Chen, Q., Zhang, J.L., Han, Y.F., Xu, B., Deng, Z.Y. and He, C.M. (2022), "Physical model test on the influence of the cutter head opening ratio on slurry shield tunnelling in a cobble layer", Tunn. Undergr. Sp. Tech., 120, 104264. https://doi.org/ 10.1016/j.tust.2021.104264.
  24. Liu, Y.K., Wu, Y., Li, W.H., Zhang, Q.S., Tai Liu, R., Bai, J.W. and Li, W. (2024), "Development of a water leakage model test system and investigation of the water leakage behavior in subsea shield tunnels during operation", Measurement, 233. https://doi.org/10.1016/j.measurement.2024.114691.
  25. Lv, J.B., Li, X.L., He, Y.W., Fu, H.L. and Yin, Y.M. (2019), "Analytical analyses of the effect of filled karst cavern on tunnel lining structure under complex geological conditions", AIP Adv., 9(3). https://doi.org/10.1063/1.5079581.
  26. Milad, Z., Masoud, R. and Daniel, D. (2020), "3D numerical investigation of segmental tunnels performance crossing a dip-slip fault", Geomech. Eng., 23(4): 351-364. https://doi.org/10.12989/gae.2020.23.4.351.
  27. Muthulingam, S. and Rao, B.N. (2015), "Non-uniform corrosion states of rebar in concrete under chloride environment", Corrosion Sci., 93, 267-282. https://doi.org/10.1016/j.corsci.2015.01.031.
  28. Qiu, P.Q., Wang, J., Ning, J.G., Liu, X.S., Hu, S.C. and Gu, Q.H. (2019), "Rock burst criteria of deep residual coal pillars in an underground coal mine: a case study", Geomech. Eng., 19(6), 499-511. https://doi.org/10.12989/gae.2019.19.6.499.
  29. Song, L., Li, J.H., Garg, A. and Mei, G.X. (2018), "Experimental study on water exchange between crack and clay matrix", Geomech. Eng., 14(3), 283-291. https://doi.org/10.12989/gae.2018.14.3.283.
  30. Vahab, S. and Abdollah, T. (2020), "Numerical simulation of the influence of interaction between Qanat and tunnel on the ground settlement", Geomech. Eng., 23(5), 455-466. https://doi.org/10.12989/gae.2020.23.5.455.
  31. Wang, S.B. and Kang, Y.L. (2022), Mechanics of Materials, Higher Education Press, Bei Jing, China.
  32. Wang, Q.S., Choe, K., Tang, J.Y., Shuai, C.J. and Wang, A.L. (2020), "Vibration analyses of general thin and moderately thick laminated composite curved beams with variable curvatures and general boundary conditions", Mech. Adv. Mater. Struct., 27(12), 991-1005. https://doi.org/10.1080/15376494.2018.1503760.
  33. Wei, Y.K. (2021), "Application strategy of integrated geophysical prospecting in the treatment of a tunnel disease", J. World Architect., 4(6), 11-14. https://doi.org/10.26689/JWA.V4I6.1745.
  34. Wen, S., Zhang, C.S. and Zhang, Y. (2019), "Favorable driving direction of double shield TBM in deep mixed rock strata: Numerical investigations to reduce shield entrapment", Geomech. Eng., 17(3), 237-245. https://doi.org/10.12989/gae.2019.17.3.237.
  35. Zhou, W.F., Liao, S.M. and Men, Y.Q. (2021), "A fluid-solid coupled modeling on water seepage through gasketed joint of segmented tunnels", Tunn. Undergr. Sp. Tech., 114, https://doi.org/10.1016/j.tust.2021.104008.
  36. Zhuang, Y., Liu, X.R., Zhou, X.H. and Du, L.B. (2022), "Diffusion model of sulfate ions in concrete based on pore change of cement mortar and its application in mesoscopic numerical simulation", Struct. Concrete, 20. https://doi.org/10.1002/suco.202100760.