DOI QR코드

DOI QR Code

Performance evaluation of natural fiber reinforced high volume fly ash foam concrete cladding

  • Raj, Amritha (Department of Civil Engineering, Amrita School of Engineering) ;
  • Sathyan, Dhanya (Department of Civil Engineering, Amrita School of Engineering) ;
  • Mini, K.M. (Department of Civil Engineering, Amrita School of Engineering)
  • Received : 2020.07.12
  • Accepted : 2021.01.13
  • Published : 2021.02.25

Abstract

The major shortcoming of concrete in most of the applications is its high self-weight and thermal conductivity. The emerging trend to overcome these shortcomings is the use of foam-concrete, which is a lightweight concrete consisting of cement, filler, water and a foaming agent. This study aims at the development of a cost-effective high-volume fly-ash foam-concrete insulation wall cladding for existing buildings using natural fiber like rice straw in different proportions. The paper reports the results of systematic studies on various mechanical, acoustic, thermal and durability properties of foam-concrete with and without replacement of cement by fly-ash. Fly-ash replaces 60 percent by weight of cement in foam-concrete. The water-solid ratio of 0.3, the filler ratio of 1:1 by weight, and the density of 1100 kg/㎥ (approx.) are fixed for all the mixes. Rice straw at 1%, 3% and 5% by weight of cement was added to improve the thermal and acoustic efficiency. From the investigations, it was inferred that the strength properties were increased with fly-ash replacement up to 1% rice straw addition. In furtherance, addition of rice straw and fly-ash resulted in improved acoustic and thermal properties.

Keywords

References

  1. Amran, Y.M., Farzadnia, N. and Ali, A.A. (2015), "Properties and applications of foamed concrete; a review", Constr. Build. Mater., 101, 990-1005. https://doi.org/10.1016/j.conbuildmat.2015.10.112.
  2. Aravind, N.R., Sathyan, D. and Mini, K.M. (2020), "Rice husk incorporated foam concrete wall panels as a thermal insulating material in buildings", Indoor Built Environ., 29(5), 721-729. https://doi.org/10.1177/1420326X19862017.
  3. Assi, I.M., Qudeimat, E.M. and Hunaiti, Y.M. (2003), "Ultimate moment capacity of foamed and lightweight aggregate concrete-filled steel tubes", Steel Compos. Struct., 3(3), 199-212. https://doi.org/10.12989/scs.2003.3.3.199.
  4. ASTM C 177 (1997), Test Method for Steady-state Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-hot-plate Apparatus, American Society for Testing Materials, Philadelphia.
  5. ASTM standard C 384-88 (1988), Standard Test Method for Impedance and Absorption of Acoustical Materials by the Impedance Tube Method, American Society for Testing Materials, Philadelphia.
  6. CanbaZ, M., Dakman, H., Arslan, B. and Buyuksungur, A. (2019), "The effect of high-temperature on foamed concrete", Comput. Concrete, 24(1), 1-6. https://doi.org/10.12989/cac.2019.24.1.001.
  7. Demirboga, R. (2003), "Influence of mineral admixtures on thermal conductivity and compressive strength of mortar", Energy Build., 35(2), 189-192. https://doi.org/10.1016/S0378-7788(02)00052-X.
  8. Falliano, D., De Domenico, D., Ricciardi, G. and Gugliandolo, E. (2018), "Experimental investigation on the compressive strength of foamed concrete: Effect of curing conditions, cement type, foaming agent and dry density", Constr. Build. Mater., 165, 735-749. https://doi.org/10.1016/j.conbuildmat.2017.12.241.
  9. Falliano, D., De Domenico, D., Ricciardi, G. and Gugliandolo, E. (2018), "Key factors affecting the compressive strength of foamed concrete", IOP Conf. Ser.: Mater. Sci. Eng., 431(6), 062009. https://doi.org/10.1088/1757-899X/431/6/062009
  10. Falliano, D., De Domenico, D., Ricciardi, G. and Gugliandolo, E. (2019), "Compressive and flexural strength of fiber-reinforced foamed concrete: Effect of fiber content, curing conditions and dry density", Constr. Build. Mater., 198, 479-493. https://doi.org/10.1016/j.conbuildmat.2018.11.197.
  11. Gowri, R.K. (2018) "Utilization of fly ash and ultrafine GGBS for higher strength foam concrete", IOP Conf. Ser.: Mater. Sci. Eng., 310, 1-10. https://doi.org/10.1088/1757-899X/310/1/012070
  12. Harada, C., Saito, Y., Nakamura, Y. and Minato, H. (2001), "The effect of sodium hydroxide treatment of rice straw on in situ disappearance of hemicellulose and lignin in its cell wall", Nihon Chikusan Gakkaiho, 72(1), 19-25. https://doi.org/10.2508/chikusan.72.19
  13. IS 12269 (2013), Ordinary Portland Cement 53 Grade-Specification, Bureau of Indian Standards, New Delhi, India.
  14. IS 13630, Part 6 (2006), Ceramic Tiles-Methods of Test, Sampling and Basis for Acceptance.
  15. IS2250 (1981), Code of Practice for Preparation and Use of Masonry Mortars, Bureau of Indian Standards, New Delhi, India.
  16. IS6441 Part-II (1972) (Reaffirmed 1997), Methods of Test for Autoclaved Cellular Concrete Products, Bureau of Indian Standards, New Delhi.
  17. Jitchaiyaphum, K., Sinsiri, T. and Chindaprasirt, P. (2011), "Cellular lightweight concrete containing pozzolan materials", Procedia Eng., 14, 1157-1164. https://doi.org/10.1016/j.proeng.2011.07.145.
  18. Jones, M.R. and McCarthy, A. (2005), "Preliminary views on the potential of foamed concrete as a structural material", Mag. Concrete Res., 57(1), 21-31. https://doi.org/10.1680/macr.2005.57.1.21.
  19. Jones, M.R., Ozlutas, K. and Zheng, L. (2017), "High-volume, ultra-low-density fly ash foamed concrete", Mag. Concrete Res., 69(22), 1146-1156. https://doi.org/10.1680/jmacr.17.00063.
  20. Kunhanandan Nambiar, E.K. and Ramamurthy, K. (2008), "Fresh state characteristics of foam concrete", J. Mater. Civil Eng., 20(2), 111-117. https://doi.org/10.1061/(ASCE)0899-1561(2008)20:2(111).
  21. Lim, S.K., Tan, C.S., Zhao, X. and Ling, T.C. (2015), "Strength and toughness of lightweight foamed concrete with different sand grading", KSCE J. Civil Eng., 19(7), 2191-2197. https://doi.org/10.1007/s12205-014-0097-y.
  22. Liu, D., Wang, F., Fu, F. and Wang, H. (2017), "Experimental research on the failure mechanism of foam concrete with C-Channel embedment", Comput. Concrete, 20(3), 263-273. https://doi.org/10.12989/cac.2017.20.3.263.
  23. Liu, J., Zhou, H. and Ouyang, P. (2013), "Effect of straw mixing amount on mechanical properties of admixture-adding hollow block", J. Wuhan Univ. Technol.-Mater. Sci. Ed., 28(3), 508-513. https://doi.org/10.1007/s11595-013-0722-5.
  24. Liu, M.Y.J., Alengaram, U.J., Jumaat, M.Z. and Mo, K.H. (2014), "Evaluation of thermal conductivity, mechanical and transport properties of lightweight aggregate foamed geopolymer concrete", Energy Build., 72, 238-245. https://doi.org/10.1016/j.enbuild.2013.12.029.
  25. Lv, X., Cao, M., Li, Y., Li, X., Li, Q., Tang, R., Wang, Q. and Duan, Y. (2015), "A new absorbing foam concrete: preparation and microwave absorbing properties", Adv. Concrete Constr., 3(2), 103-111. http://dx.doi.org/10.12989/acc.2015.3.2.103.
  26. Madhwani, H., Sathyan, D. and Mini, K.M. (2020), "Study on durability and hardened state properties of sugarcane bagasse fiber reinforced foam concrete", Mater. Today Proc. https://doi.org/10.1016/j.matpr.2020.10.313.
  27. Mahlia, T.M.I., Taufiq, B.N. and Masjuki, H.H. (2007), "Correlation between thermal conductivity and the thickness of selected insulation materials for building wall", Energy Build., 39(2), 182-187. https://doi.org/10.1016/j.enbuild.2006.06.002.
  28. Morsy, M.I.N. (2011) "Properties of rice straw cementitious composite", Univ. Tech. Darmstadt, Allemagne.
  29. Nambiar, E.K. and Ramamurthy, K. (2007), "Air-void characterisation of foam concrete", Cement Concrete Res., 37(2), 221-230. ttps://doi.org/10.1016/j.cemconres.2006.10.009.
  30. Nambiar, E.K. and Ramamurthy, K. (2009), "Shrinkage behavior of foam concrete", J. Mater. Civil Eng., 21(11), 631-636. https://doi.org/10.1061/(ASCE)0899-1561(2009)21:11(631).
  31. Nambiar. E.K. and Ramamurthy. K. (2006), "Influence of filler type on the properties of foam concrete", Cement Concrete Compos., 28(5), 475-480. https://doi.org/10.1016/j.cemconcomp.2005.12.001.
  32. Nandi, S., Chatterjee, A., Samanta, P. and Hansda, T. (2016), "Cellular concrete and its facets of application in civil engineering", Int. J. Eng. Res., 5(1), 37-43.
  33. Panesar, D.K. (2013), "Cellular concrete properties and the effect of synthetic and protein foaming agents", Constr. Build. Mater., 44, 575-584. https://doi.org/10.1016/j.conbuildmat.2013.03.024.
  34. Raj, A., Sathyan, D. and Mini, K.M. (2019), "Physical and functional characteristics of foam concrete: A review", Constr. Build. Mater., 221, 787-799. https://doi.org/10.1016/j.conbuildmat.2019.06.052.
  35. Raj, B., Sathyan, D., Madhavan, M.K. and Raj, A. (2020), "Mechanical and durability properties of hybrid fiber reinforced foam concrete", Constr. Build. Mater., 245, 118373, https://doi.org/10.1016/j.conbuildmat.2020.118373.
  36. Reisi, M., Dadvar, S.A. and Sharif, A. (2017), "Microstructure and mixture proportioning of non-structural foamed concrete with silica fume", Mag. Concrete Res., 69(23), 1218-1230. https://doi.org/10.1680/jmacr.17.00066.
  37. Saje, D., Bandelj, B., Sustersic, J., Lopatic, J. and Saje, F. (2011), "Shrinkage of polypropylene fibre reinforced high performance concrete", J. Mater. Civil Eng., 23(7), 941-952. https://doi.org/10.1061/(ASCE)MT.1943-5533.0000258.
  38. Saygili, A. and Baykal, G. (2011), "A new method for improving the thermal insulation properties of fly ash.", Energy Build., 43(11), 3236-3242. https://doi.org/10.1016/j.enbuild.2011.08.024.
  39. Sengul, O., Azizi, S., Karaosmanoglu, F. and Tasdemir, M.A. (2011), "Effect of expanded perlite on the mechanical properties and thermal conductivity of lightweight concrete", Energy Build., 43(2-3), 671-676. https://doi.org/10.1016/j.enbuild.2010.11.008.
  40. Usubharatana, P. and Phungrassami, H. (2015), "Development of thermal insulation materials for packaging made from agricultural wastes", Acad. J. Sci., 4, 133-141.