Advances in materials Research

  • 제9권2호
  • /
  • Pages.99-107
  • /
  • 2020
  • /
  • 2234-0912(pISSN)
  • /
  • 2234-179X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Effect of Tio2 particles on the mechanical, bonding properties and microstructural evolution of AA1060/TiO2 composites fabricated by WARB

  • Vini, Mohamad Heydari (Department of Mechanical Engineering, Mobarakeh Branch, Islamic Azad University) ;
  • Daneshmand, Saeed (Department of Mechanical Engineering, Majlesi Branch, Islamic Azad University)
  • 투고 : 2019.09.17
  • 심사 : 2020.03.26
  • 발행 : 2020.06.25
⟨ 이전 논문 다음 논문 ⟩

초록

Reinforced aluminum alloy base composites have become increasingly popular for engineering applications, since they usually possess several desirable properties. Recently, Warm Accumulative Roll Bonding (WARB) process has been used as a new novel process to fabricate particle reinforced metal matrix composites. In the present study, TiO2 particles are used as reinforcement in aluminum metal matrix composites fabricated through warm accumulative roll bonding process. Firstly, the raw aluminum alloy 1060 strips with TiO2 as reinforcement particle were roll bonded to four accumulative rolling cycles by preheating for 5 min at 300℃before each cycle. The mechanical and bonding properties of composites have been studied versus different volume contents of TiO2 particles by tensile test, peeling test and vickers micro-hardness test. Moreover, the fracture surface and peeling surface of samples after the tensile test and peeling test have been studied versus different amount of TiO2 volume contents by scanning electron microscopy. The results indicated that the strength and the average vickers micro-hardness of composites improved by increasing the volume content of TiO2 particles and the amount of their elongation and bonding strength decreased significantly.

키워드

참고문헌

  1. Baazamat, S., Tajally, M. and Borhani, E. (2015), "Fabrication and characteristic of al-based hybrid nanocomposite reinforced with wo3 and sic by accumulative roll bonding process", J. Alloys Compounds, 653, 39-46. http://dx.doi.org/10.1016/j.jallcom.2015.08.267
  2. Chin, E.S. (1999), "Army focused team on functionally graded armor composites", Mater. Sci. Eng. A, 259, 155-161. https://doi.org/10.1016/S0921-5093 (98)00883-1
  3. Darmiani, E., Danaee, I., Golozar, M.A. and Toroghinejad, M.R. (2013), "Corrosion investigation of Al - Sic nano-composite fabricated by accumulative roll bonding (ARB) process", J. Alloys Compounds, 552, 31-39. https://doi.org/10.1016/j.jallcom.2012.10.069
  4. Eizadjou, M., Manesh, H.D. and Janghorban, K. (2008), "Investigation of roll bonding between aluminum alloy strips", Mater. Des., 29(4), 909-913. https://doi.org/10.1016/j.matdes.2007.03.020
  5. Emadinia, O., Simoes, S., Viana, F., Vieira, M.F., Cavaleiro, A.J., Ramos, A.S. and Vieira, M.T. (2016), "Cold rolled versus sputtered Ni/Ti multilayers for reaction-assisted diffusion bonding", Weld. World, 60(2), 337-344. https://doi.org/10.1007/s40194-015-0282-8
  6. Heydari Vini, M., Sedighi, M. and Mondali, M. (2016), "Mechanical properties and microstructural evolution of AA5083/Al2O3 composites fabricated by warm accumulative roll bonding", J. Adv. Des. Manuf. Technol., 9(4), 13-22.
  7. Jamaati, R., Amirkhanlou, S., Toroghinejad, M.R. and Niroumand, B. (2011), "Effect of particle size on microstructure and mechanical properties of composites produced by ARB process", Mater. Sci. Eng. A, 528(4-5), 2143-2148. https://doi.org/10.1016/j.msea.2010.11.056
  8. Kaczmar, J.W., Pietrzak, K. and Wlosinski, W. (2000), "The production and application of metal matrix composite materials", J. Mater. Process. Technol., 106(1-3), 58-67. https://doi.org/10.1016/S0924-0136(00)00639-7
  9. Mandal, D., Dutta, B.K. and Panigrahi, S.C. (2007), "Dry sliding wear behavior of stir cast aluminium base short steel fiber reinforced composites", J. Mater. Sci., 42, 8622-8628. https://doi.org/10.1007/s10853-006-1271-5
  10. Ng, M.K., Li, L., Fan, Z., Gao, R.X., Smith III, E.F., Ehmann, K.F. and Cao, J. (2015), "Joining sheet metals by electrically-assisted roll bonding", CIRP Annals - Manuf. Technol., 64(1), 273-276. https://doi.org/10.1016/j.cirp.2015.04.131
  11. Reihanian, M., Hadadian, F.K. and Paydar, M.H. (2014), "Fabrication of Al-2 Vol% $Al_2O_3$/SiC hybrid composite via accumulative roll bonding (ARB): an investigation of the microstructure and mechanical properties", Mater. Sci. Eng. A, 607, 88-196. https://doi.org/10.1016/j.msea.2014.04.013
  12. Saito, Y., Utsunomiya, H., Tsuji, N. and Sakai, T. (1999), "Novel ultra-high straining process for bulk materials development of the accumulative roll-bonding (ARB) process", Acta Mater., 47, 579-583. https://doi.org/10.1016/S1359-6454(98)00365-6
  13. Sedighi, M., Heydari Vini, M. and Farhadipour, P. (2016a), "Effect of alumina content on the mechanical properties of AA5083/$Al_2O_3$ composites fabricated by warm accumulative roll bonding", J. Powder Metallur. Metal Ceram., 55(7-8), 413-418. http://dx.doi.org/10.1007%2Fs11106-016-9821-0 https://doi.org/10.1007/s11106-016-9821-0
  14. Sedighi, M., Heydari Vini, M. and Farhadipour, P. (2016b), "Investigation of roll bonding between AA5083 strips", Adv. Mater. Process., 4(3), 33-42.