Steel and Composite Structures

  • 제34권5호
  • /
  • Pages.681-698
  • /
  • 2020
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Machinability investigation and sustainability assessment in FDHT with coated ceramic tool

  • Panda, Asutosh (Department of Production Engineering, Veer Surendra Sai University of Technology) ;
  • Das, Sudhansu Ranjan (Department of Production Engineering, Veer Surendra Sai University of Technology) ;
  • Dhupal, Debabrata (Department of Production Engineering, Veer Surendra Sai University of Technology)
  • 투고 : 2019.05.21
  • 심사 : 2020.01.27
  • 발행 : 2020.03.10
⟨ 이전 논문 다음 논문 ⟩

초록

The paper addresses contribution to the modeling and optimization of major machinability parameters (cutting force, surface roughness, and tool wear) in finish dry hard turning (FDHT) for machinability evaluation of hardened AISI grade die steel D3 with PVD-TiN coated (Al2O3-TiCN) mixed ceramic tool insert. The turning trials are performed based on Taguchi's L18 orthogonal array design of experiments for the development of regression model as well as adequate model prediction by considering tool approach angle, nose radius, cutting speed, feed rate, and depth of cut as major machining parameters. The models or correlations are developed by employing multiple regression analysis (MRA). In addition, statistical technique (response surface methodology) followed by computational approaches (genetic algorithm and particle swarm optimization) have been employed for multiple response optimization. Thereafter, the effectiveness of proposed three (RSM, GA, PSO) optimization techniques are evaluated by confirmation test and subsequently the best optimization results have been used for estimation of energy consumption which includes savings of carbon footprint towards green machining and for tool life estimation followed by cost analysis to justify the economic feasibility of PVD-TiN coated Al2O3+TiCN mixed ceramic tool in FDHT operation. Finally, estimation of energy savings, economic analysis, and sustainability assessment are performed by employing carbon footprint analysis, Gilbert approach, and Pugh matrix, respectively. Novelty aspects, the present work: (i) contributes to practical industrial application of finish hard turning for the shaft and die makers to select the optimum cutting conditions in a range of hardness of 45-60 HRC, (ii) demonstrates the replacement of expensive, time-consuming conventional cylindrical grinding process and proposes the alternative of costlier CBN tool by utilizing ceramic tool in hard turning processes considering technological, economical and ecological aspects, which are helpful and efficient from industrial point of view, (iii) provides environment friendliness, cleaner production for machining of hardened steels, (iv) helps to improve the desirable machinability characteristics, and (v) serves as a knowledge for the development of a common language for sustainable manufacturing in both research field and industrial practice.

키워드

참고문헌

  1. Anand, A., Behera, A.K. and Das, S.R. (2019), "An overview on economic machining of hardened steels by hard turning and its process variables", Manufact. Rev., 6, 4. https://doi.org/10.1051/mfreview/2019002.
  2. Aouici, H., Bouchelaghem, H., Yallese, M.A., Elbah, M. and Fnides, B. (2014), "Machinability investigation in hard turning of AISI D3 cold work steel with ceramic tool using response surface methodology", Int. J. Adv. Manufact. Technol., 73(9-12), 1775-1788. https://doi.org/10.1007/s00170-014-5950-0.
  3. Aouici, H., Khellaf, A., Smaiah, S., Elbah, M., Fnides, B. and Yallese, M.A. (2017), "Comparative assessment of coated and uncoated ceramic tools on cutting force components and tool wear in hard turning of AISI H11 steel using Taguchi plan and RMS", Sadhana, 42(12), 2157-2170. https://doi.org/10.1007/s12046-017-0746-1.
  4. Asilturk, I. (2012), "Predicting surface roughness of hardened AISI 1040 based on cutting parameters using neural networks and multiple regression", Int. J. Adv. Manufact. Technol., 63(1-4), 249-257. https://doi.org/10.1007/s00170-012-3903-z.
  5. Astakhov, V.P. (2011), Machining of Hard Materials - Definitions and Industrial Applications, In: J. Paulo Davim (ed.), Machining of Hard Materials. Springer-Verlag, London, 1-32.
  6. Bartarya, G. and Choudhury, S.K. (2013), "Influence of machining parameters on forces and surface roughness during finish hard turning of EN 31 steel", Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manufact., 228(9), 1068-1080. https://doi.org/10.1177/0954405413500492
  7. Benlahmidi, S., Aouici, H., Boutaghane, F., Khellaf, A., Fnides, B., and Yallese, M. (2016), "Design optimization of cutting parameters when turning hardened AISI H11 steel (50 HRC) with CBN7020 tools", Int. J. Adv. Manufact. Technol., 89(1-4), 803-820. https://doi.org/10.1007/s00170-016-9121-3.
  8. Bensouilah, H., Aouici, H., Meddour, I., Yallese, M.A., Mabrouki, T. and Girardin, F. (2016), "Performance of coated and uncoated mixed ceramic tools in hard turning process", Measurement, 82, 1-18. https://doi.org/10.1016/j.measurement.2015.11.042.
  9. Bouacha, K., Yallese, M.A., Khamel, S. and Belhadi, S. (2014), "Analysis and optimization of hard turning operation using cubic boron nitride tool", Int. J. Refractory Metals Hard Mater., 45, 160-178. https://doi.org/10.1016/j.ijrmhm.2014.04.014.
  10. Bouacha, K. and Terrab, A. (2016), "Hard turning behavior improvement using NSGA-II and PSO-NN hybrid model", Int. J. Adv. Manufact. Technol., 86(9-12), 3527-3546. ttps://doi.org/10.1007/s00170-016-8479-6.
  11. Bouzid, L., Yallese, M.A., Chaoui, K., Mabrouki, T. and Boulanouar, L. (2014), "Mathematical modeling for turning on AISI 420 stainless steel using surface response methodology", Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manufact., 229(1), 45-61. https://doi.org/10.1177/0954405414526385.
  12. Chinchanikar, S. and Choudhury, S.K. (2013), "Investigations on machinability aspects of hardened AISI 4340 steel at different levels of hardness using coated carbide tools", Int. J. Refractory Metals Hard Mater., 38, 124-133. https://doi.org/10.1016/j.ijrmhm.2013.01.013.
  13. Costa, N.R., Lourenco, J. and Pereira, Z.L. (2011), "Desirability function approach: A review and performance evaluation in adverse conditions", Chemometrics Intel.Laboratory Syst., 107(2), 234-244. https://doi.org/10.1016/j.chemolab.2011.04.004.
  14. Das, A., Mukhopadhyay, A., Patel, S.K. and Biswal, B.B. (2016), "Comparative assessment on machinability aspects of AISI 4340 alloy steel using uncoated carbide and coated cermet inserts during hard turning", Arabian J. Sci. Eng., 41(11), 4531-4552. https://doi.org/10.1007/s13369-016-2160-0.
  15. Das, A., Patel, S.K., Hotta, T.K. and Biswal, B.B. (2018), "Statistical analysis of different machining characteristics of EN-24 alloy steel during dry hard turning with multilayer coated cermet inserts", Measurement, 134, 123-141. https://doi.org/10.1016/j.measurement.2018.10.065.
  16. Das, A., Tirkey, N., Patel, S.K., Das, S.R. and Biswal, B.B. (2019), "A comparison of machinability in hard turning of EN-24 alloy steel under mist cooled and dry cutting environments with a coated cermet tool", J. Fail. Anal. Prevention, 19, 115-130. https://doi.org/10.1007/s11668-018-0574-6.
  17. Das, S.R., Dhupal, D. and Kumar, A. (2015), "Experimental investigation into machinability of hardened AISI 4140 steel using TiN coated ceramic tool", Measurement, 62, 108-126. https://doi.org/10.1016/j.measurement.2014.11.008.
  18. Davim, J.P. and Figueira, L. (2007), "Comparative evaluation of conventional and wiper ceramic tools on cutting forces, surface roughness, and tool wear in hard turning AISI D2 steel", Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manufact., 221(4), 625-633. https://doi.org/10.1243/09544054JEM762.
  19. Davim, J.P. and Figueira, L. (2007), "Machinability evaluation in hard turning of cold work tool steel (D2) with ceramic tools using statistical techniques", Mater. Design, 28(4), 1186-1191. https://doi.org/10.1016/j.matdes.2006.01.011.
  20. Fnides, B., Aouici, H., Elbah, M., Boutabba, S. and Boulanouar, L. (2015), "Comparison between mixed ceramic and reinforced ceramic tools in terms of cutting force components modelling and optimization when machining hardened steel AISI 4140 (60 HRC)", Mechanics Industry, 16(6), 609. https://doi.org/10.1051/meca/2015036.
  21. Gaitonde, V.N., Karnik, S.R., Figueira, L. and Paulo Davim, J. (2009a), "Machinability investigations in hard turning of AISI D2 cold work tool steel with conventional and wiper ceramic inserts", Int. J. Refractory Metals Hard Mater., 27(4), 754-763. https://doi.org/10.1016/j.ijrmhm.2008.12.007
  22. Gaitonde, V.N., Karnik, S.R., Figueira, L. and Davim, J.P. (2009b), "Analysis of machinability during hard turning of cold work tool steel (Type: AISI D2)", Mater. Manufact. Processes, 24(12), 1373-1382. https://doi.org/10.1080/10426910902997415.
  23. Gaitonde, V.N., Karnik, S.R., Figueira, L. and Davim, J.P. (2010), "Performance comparison of conventional and wiper ceramic inserts in hard turning through artificial neural network modeling", Int. J. Adv. Manufact. Technol., 52(1-4), 101-114. https://doi.org/10.1007/s00170-010-2714-3.
  24. Grzesik, W. (2008), Machining of hard materials, In: J. Paulo Davim (ed.), Machining Fundamentals and Recent Advances. Springer-Verlag, London.
  25. Gunay, M. and Yucel, E. (2013), "Application of Taguchi method for determining optimum surface roughness in turning of high-alloy white cast iron", Measurement, 46(2), 913-919. https://doi.org/10.1016/j.measurement.2012.10.013.
  26. Hessainia, Z., Belbah, A., Yallese, M.A., Mabrouki, T. and Rigal, J.F. (2013), "On the prediction of surface roughness in the hard turning based on cutting parameters and tool vibrations", Measurement, 46(5), 1671-1681. https://doi.org/10.1016/j.measurement.2012.12.016.
  27. Keblouti, O., Boulanouar, L., Azizi, M.A. and Yallese, M.A. (2017), "Effects of coating material and cutting parameters on the surface roughness and cutting forces in dry turning of AISI 52100 steel", Struct. Eng. Mech., 61(4), 519-526. https://doi.org/10.12989/sem.2017.61.4.519.
  28. Khamel, S., Ouelaa, N. and Bouacha, K. (2012), "Analysis and prediction of tool wear, surface roughness and cutting forces in hard turning with CBN tool", J. Mech. Sci. Technol., 26(11), 3605-3616. https://doi.org/10.1007/s12206-012-0853-1.
  29. Khellaf, A., Aouici, H., Smaiah, S., Boutabba, S., Yallese, M.A. and Elbah, M. (2016), "Comparative assessment of two ceramic cutting tools on surface roughness in hard turning of AISI H11 steel: including 2D and 3D surface topography", Int. J. Adv. Manufact. Technol., 89(1-4), 333-354. https://doi.org/10.1007/s00170-016-9077-3.
  30. Kishawy, H.A. and Elbestawi, M.A. (2001), "Tool wear and surface integrity during high-speed turning of hardened steel with polycrystalline cubic boron nitride tools", Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manufact., 215(6), 755-767. https://doi.org/10.1243/0954405011518700.
  31. Kumar, P. and Chauhan, S.R. (2015), "Machinability study on finish turning of AISI H13 hot working die tool steel with Cubic Boron Nitride (CBN) cutting tool Inserts using response Surface Methodology (RSM)", Arabian J. Sci. Eng., 40(5), 1471-1485. https://doi.org/10.1007/s13369-015-1606-0.
  32. Kumar, R., Sahoo, A.K., Mishra, P.C. and Das, R.K. (2018). "Comparative study on machinability improvement in hard turning using coated and uncoated carbide inserts: part II modeling, multi-response optimization, tool life, and economic aspects", Adv. Manufact., 6(2), 155-175. https://doi.org/10.1007/s40436-018-0214-0.
  33. Kumar, S., Singh, D. and Kalsi, N.S. (2016), "Surface quality evaluation of AISI 4340 steel having varying hardness during machining with TiN-coated CBN inserts", Proceedings of the Institution of Mechanical Engineers, Part J: Eng. Tribology, 231(7), 925-933. https://doi.org/10.1177/1350650116684243.
  34. Laouissi, A., Yallese, M.A., Belbah, A., Belhadi, S. and Haddad, A. (2018), "Investigation, modeling, and optimization of cutting parameters in turning of gray cast iron using coated and uncoated silicon nitride ceramic tools. Based on ANN, RSM, and GA optimization", Int. J. Adv. Manufact. Technol., 101(1-4), 523-548. https://doi.org/10.1007/s00170-018-2931-8.
  35. Liu, M., Takagi, J. and Tsukuda, A. (2004), "Effect of tool nose radius and tool wear on residual stress distribution in hard turning of bearing steel", J. Mater. Processing Technol., 150(3), 234-241. https://doi.org/10.1016/j.jmatprotec.2004.02.038.
  36. Meddour, I., Yallese, M.A., Khattabi, R., Elbah, M. and Boulanouar, L. (2014), "Investigation and modeling of cutting forces and surface roughness when hard turning of AISI 52100 steel with mixed ceramic tool: cutting conditions optimization", Int. J. Adv. Manufact. Technol., 77(5-8), 1387-1399. https://doi.org/10.1007/s00170-014-6559-z.
  37. Meddour, I., Yallese, M.A., Bensouilah, H., Khellaf, A. and Elbah, M. (2018), "Prediction of surface roughness and cutting forces using RSM, ANN, and NSGA-II in finish turning of AISI 4140 hardened steel with mixed ceramic tool", Int. J. Adv. Manufact. Technol., 97(5-8), 1931-1949. https://doi.org/10.1007/s00170-018-2026-6.
  38. Mondal, K. and Das, S. (2017), "An investigation on machinability during turning hardened steel in dry condition", J. Institution Engineers (India): Series C, 99(6), 637-644. https://doi.org/10.1007/s40032-017-0370-1.
  39. Nayak, M. and Sehgal, R. (2015), "Effect of tool material properties and cutting conditions on machinability of AISI D6 steel during hard turning.", Arabian J. Sci. Eng., 40(4), 1151-1164. https://doi.org/10.1007/s13369-015-1578-0
  40. Nouioua, M., Yallese, M.A., Khettabi, R., Belhadi, S., Bouhalais, M.L. and Girardin, F. (2017), "Investigation of the performance of the MQL, dry, and wet turning by response surface methodology (RSM) and artificial neural network (ANN)", Int. J. Adv. Manufact. Technol., 93(5-8), 2485-2504. https://doi.org/10.1007/s00170-017-0589-2.
  41. Panda, A., Sahoo, A.K. and Rout, A.K. (2016), "Investigations on surface quality characteristics with multi-response parametric optimization and correlations", Alexandria Eng. J., 55(2), 1625-1633. https://doi.org/10.1016/j.aej.2016.02.008.
  42. Panda, A., Das, S.R. and Dhupal, D. (2017), "Surface roughness analysis for economical feasibility study of coated ceramic tool in hard turning operation", Process Integration Optim. Sustainability, 1(4), 237-249. https://doi.org/10.1007/s41660-017-0019-9.
  43. Quiza, R., Figueira, L. and Paulo Davim, J. (2007), "Comparing statistical models and artificial neural networks on predicting the tool wear in hard machining D2 AISI steel", Int. J. Adv. Manufact. Technol., 37(7-8), 641-648. ttps://doi.org/10.1007/s00170-007-0999-7.
  44. Sahoo, A.K. and Sahoo, B. (2013), "Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-II (RSM, grey relational and techno economical approach)", Measurement, 46(8), 2868-2884. https://doi.org/10.1016/j.measurement.2012.09.023.
  45. Sharma, V. S., Dhiman, S., Sehgal, R. and Sharma, S.K. (2008), "Estimation of cutting forces and surface roughness for hard turning using neural networks", J. Intel. Manufact., 19(4), 473-483. https://doi.org/10.1007/s10845-008-0097-1.
  46. Shihab, S.K., Khan, Z.A., Mohammad, A. and Siddiquee, A.N. (2014), "Optimization of surface integrity in dry hard turning using RSM", Sadhana, 39(5), 1035-1053. https://doi.org/10.1007/s12046-014-0263-4.
  47. Shaw, M.C. (2005), Metal Cutting Principles, second edition, Oxford University Press, New York.
  48. Suresh, R., Basavarajappa, S., Gaitonde, V.N. and Samuel, G.L. (2012), "Machinability investigations on hardened AISI 4340 steel using coated carbide insert", Int. J. Refractory Metals Hard Mater., 33, 75-86. https://doi.org/10.1016/j.ijrmhm.2012.02.019.
  49. Suresh, R., Basavarajappa, S., Gaitonde, V.N., Samuel, G. and Davim, J.P. (2013), "State-of-the-art research in machinability of hardened steels", Proceedings of the Institution of Mechanical Engineers, Part B: J. Eng. Manufact., 227(2), 191-209. https://doi.org/10.1177/0954405412464589.
  50. Tang, L., Cheng, Z., Huang, J., Gao, C. and Chang, W. (2014), "Empirical models for cutting forces in finish dry hard turning of hardened tool steel at different hardness levels", Int. J. Adv. Manufact. Technol., 76(1-4), 691-703. https://doi.org/10.1007/s00170-014-6291-8.
  51. Xiao, Z., Liao, X., Long, Z. and Li, M. (2016), "Effect of cutting parameters on surface roughness using orthogonal array in hard turning of AISI 1045 steel with YT5 tool", Int. J. Adv. Manufact. Technol., 93(1-4), 273-282. https://doi.org/10.1007/s00170-016-8933-5.
  52. Xie, N., Zhou, J. and Zheng, B. (2018), "An energy-based modeling and prediction approach for surface roughness in turning", Int. J. Adv. Manufact. Technol., 96(5-8), 2293-2306. https://doi.org/10.1007/s00170-018-1738-y.
  53. Zerti, O., Yallese, M.A., Khettabi, R., Chaoui, K. and Mabrouki, T. (2016), "Design optimization for minimum technological parameters when dry turning of AISI D3 steel using Taguchi method", Int. J. Adv. Manufact. Technol., 89(5-8), 1915-1934. https://doi.org/10.1007/s00170-016-9162-7.
  54. Zerti, A., Yallese, M.A., Meddour, I., Belhadi, S., Haddad, A. and Mabrouki, T. (2018), "Modeling and multi-objective optimization for minimizing surface roughness, cutting force, and power, and maximizing productivity for tempered stainless steel AISI 420 in turning operations", Int. J. Adv. Manufact. Technol., doi:10.1007/s00170-018-2984-8.
  55. Zhao, T., Zhou, J.M., Bushlya, V. and Stahl, J.E. (2017), "Effect of cutting edge radius on surface roughness and tool wear in hard turning of AISI 52100 steel", Int. J. Adv. Manufact. Technol., 91(9-12), 3611-3618. https://doi.org/10.1007/s00170-017-0065-z

피인용 문헌

  1. Design optimization for analysis of surface integrity and chip morphology in hard turning vol.76, pp.5, 2020, https://doi.org/10.12989/sem.2020.76.5.561
  2. Real 3D turning simulation of materials with cylindrical shapes using ABAQUS/Explicit vol.43, pp.8, 2020, https://doi.org/10.1007/s40430-021-03075-5