Advances in materials Research

  • 제8권1호
  • /
  • Pages.25-36
  • /
  • 2019
  • /
  • 2234-0912(pISSN)
  • /
  • 2234-179X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Effect of waste aluminium shavings on the bond characteristics of laterized concrete

  • Ofuyatan, Olatokunbo M. (Department of Civil Engineering, Covenant University) ;
  • Ivoke, Anthony A. (Department of Civil Engineering, university of Lagos,) ;
  • Olowofoyeku, Adeoye M. (Department of Civil Engineering, Yaba College of Technology) ;
  • Adesina, Adeyemi (Department of Civil Engineering, Covenant University) ;
  • Oluwafemi, John (Department of Civil Engineering, Covenant University)
  • 투고 : 2019.02.04
  • 심사 : 2019.03.19
  • 발행 : 2019.03.25
⟨ 이전 논문 다음 논문 ⟩

초록

The utilization of fibre in concrete production not only solves the problem of disposing this solid waste but helps conserve natural resources. This study investigated the effect of waste aluminum shavings on bond strength of laterized concrete. Laterized concrete spliced beams of $150{\times}250{\times}2150mm$ and $175{\times}275{\times}2300mm$ were prepared. Fifteen specimens with 16 mm and 20 mm were cast with the addition of aluminium shavings at varying percentages of 1vol%, 1.5vol% and 2vol%; another ten specimens with 16 mm and 20 mm diameter bars at 0% of aluminium shavings were cast as control. Concrete cubes of number were prepared, three taken for each set of various percentages of aluminium shavings were used to determine the concrete strength. It was observed from the analysis that the compressive strength decreased as the percentage of aluminium shavings increased, while the aluminium shavings increased the bond between concrete and steel. However, for normal concrete there was an increase in bond resistance with increase in aluminium shavings. The bond resistance of 16 mm was found to be higher than that of 20 mm in all the specimens tested.

키워드

과제정보

연구 과제 주관 기관 : University of Lagos

참고문헌

  1. ACI-318 (2008), Building Code Requirements for Structural Concrete and Commentary, American Concrete Institute; Farmington Hills, Manchester Institute, USA.
  2. ACI-408 (2003), Bond and Development of Straight Reinforcing Bars in Tension, American Concrete Institute; Farmington Hills, Manchester Institute, USA.
  3. ASTMC 1064 (2008), Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete; Annual Book of ASTM Standards, West Conshohocken, PA, USA.
  4. BS12:1996 (1996), Specification for Portland cement (Ordinary and Rapid-Hardening) Part 2; British Standards Institution, London, UK.
  5. BS8110 (1997), Structural use of Concrete Part 1. Code of Practice for Design and Construction; British Standards Institution, London, UK.
  6. Cairns, J. and Abdullah, R. (1994), "Fundamental tests on the effect of an epoxy coating on bond strength", ACI Mater. J., 91(4), 331-338.
  7. Hosford, W.F. and Duncan, J.L. (1994), "The aluminum beverage can", Sci. American, 271(3), 48-53. https://doi.org/10.1038/scientificamerican0994-48
  8. Kazim, T. and Ahmet, B. (2009), "Bond strength of tension lap-splices in full scale self-compacting concrete beams", J. Sci. Direct. 3(9-11), 145.
  9. Murali, G., Vardhan, C.V., Prabu, R., Khan, Z.M.S.A., Mohamed, T.A. and Suresh, T (2012), "Experimental investigation on fibre reinforced concrete using waste materials", J. Eng. Res. Appl., 2(2), 278-283.
  10. Ofuyatan, O., Adedeji, A., Omeje, M. and Olawale, S. (2017), "Interaction assessment and optimal design of composite action of plastered typha strawbale", Adv. Mater. Res., Int. J., 6(2), 221-231. http://dx.doi.org/10.12989/amr.2017.6.2.221
  11. Ofuyatan, O.M., Ede, A.N., Olofinnade, O.M., Oyebisi, S.O., Alayande, T. and Ogundipe, J. (2018), "Assessment of strength properties of cassava peel ash concrete", J. Civil Eng. Technol., 9(1), 965-974.
  12. Osifala, K.B. and Akeju, T.A. (2010), "Effects of increased concrete cover on bond efficiency of coated reinforcing bars", Australian J. Struct. Eng., 10(2), 179-190. https://doi.org/10.1080/13287982.2010.11465043
  13. Seara-Paz, S., Gonzalez-Fonteboa, B., Eiras-Lopez, J. and Herrador, M.F. (2014), "Bond behavior between steel reinforcement and recycled concrete", J. Mater. Struct., 47, 323-334. https://doi.org/10.1617/s11527-013-0063-z
  14. Yoo, D.Y., Shin, H.O., Yang, J.M. and Yoon, Y.S. (2014), "Material and bond properties of ultra-high performance fibre reinforced concrete with micro steel fibres", J. Compos. Eng., 58, 122-133. https://doi.org/10.1016/j.compositesb.2013.10.081

피인용 문헌

  1. Roles of aluminium shavings and calcite on engineering properties of cement-based composites vol.277, 2019, https://doi.org/10.1016/j.jclepro.2020.124104