DOI QR코드

DOI QR Code

반응성염료에 의한 폐MDF 재생 목질섬유의 염색특성

The Dyeing Properties of Woody Fiber Regenerated from Waste MDF by Reactive Dyes

  • Ju, Seon-Gyeong (Department of Interior Materials Engineering, Gyeongnam National University of Science Technology) ;
  • Roh, JeongKwan (Department of Interior Materials Engineering, Gyeongnam National University of Science Technology)
  • 투고 : 2019.01.29
  • 심사 : 2019.02.18
  • 발행 : 2019.03.25

초록

폐MDF로부터 해섬하여 얻은 재생섬유를 Reactive Red H-E3B (Bis-monochlorotriazine(MCT)/MCT type)와 Reactive Red RB 133%(bis-monochlorotriazine/Vinyl sulphone type)로 염색할 때 최적의 염색조건을 구명하기 위하여 염색조건(염료 농도, 염과 알칼리 첨가량, 염색온도)과 염색특성 및 일광견뢰도와의 관계를 검토하였다. 2종의 반응성염료 모두 염료농도가 1~10(%,OWF)로 증가함에 따라 염착량(K/S)은 증가하였다. 또한, H-E3B가 RB 133%보다 염료 농도에 관계없이 K/S는 높았으며, 자외선 조사에 따른 색차는 낮아 자외선에 의한 변색 저항성이 양호하였다. 황산나트륨의 첨가량이 증가할수록 색차 및 K/S도 증가하였으며, 염의 첨가량은 50~70 g/L가 적절하였다. 2 g/L의 탄산나트륨 첨가에 의해 색차 및 K/S가 크게 증가하였으나 그 이상의 첨가량 증가에서는 거의 차이가 없었다. 탄산나트륨의 첨가량은 pH 10을 유지하는 5~10 g/L가 적절할 것으로 생각된다. H-E3B 염료는 염색 온도가 높아짐에 따라 염착량이 증가하다가 $80^{\circ}C$에서 다시 감소한 반면 RB 133%는 $60{\sim}70^{\circ}C$까지는 거의 동일한 염착량을 나타냈으나, 이후 감소하였다. 따라서 H-E3B는 $80^{\circ}C$, RB 133%는 $60^{\circ}C$가 적정한 것으로 판단된다. 이상의 최적조건에서 폐MDF 목질섬유를 염색처리하면 H-E3B염료는 1.5~2.0R, RB 133%염료는 9.6~10.0 PR의 색상을 가지는 염색 재생 목질섬유의 제조가 가능하였다.

This study aims to review the relations between the dyeing conditions (i.e., dye concentration, addition amounts of salt and alkali, and dyeing temperature) and dyeing properties and color fastness to light for identifying the optimal dyeing conditions when dyed regenerated woody fibers were obtained through the defibration of waste medium density fiberboard (MDF) using reactive Red H-E3B (Bis-monochlorotriazine (MCT)/MCT type) and reactive Red RB133% (Bis-MCT/Vinyl sulphone type). The dyeing yield (K/S) obtained using two types of reactive dyes increased as the dye concentration increased by 1-10% (on the weight of fiber (OWF)). In addition, the K/S of H-E3B was higher than that of RB133% irrespective of the dye concentration. The color difference of H-E3B after ultraviolet (UV) radiation was lower than that of RB133%, denoting good resistance to discoloration by UV. As the amount of sodium sulfate increased, the color difference and K/S also increased, and the adequate salt content was determined to be 50-70 g/L. Further, the color difference and K/S significantly increased only the addition of 2 g/L of sodium carbonate; however, almost no difference was observed when more than 2 g/L of sodium carbonate was added. The addition amount of sodium carbonate was adequate 5-10 g/L to dyeing the fiber and the pH at this addition level was 10. The dyeing yield of H-E3B increased when the dyeing temperature increased; however, it subsequently decreased after the dyeing temperature became $80^{\circ}C$. The dyeing yield of RB133% was almost the same up to $60-70^{\circ}C$ but declined subsequently. Thus, the adequate temperatures were $80^{\circ}C$ and $60^{\circ}C$ for H-E3B and RB133%, respectively. If the waste MDF woody fiber was dyed under the aforementioned optimal conditions, dyed regenerated woody fiber can be obtained having the following colors: 1.5 to 2.0R with the H-E3B dye and 9.6 to 10.0 PR with RB133%.

키워드

HMJGBP_2019_v47n2_163_f0001.png 이미지

Fig. 1. Dyeing profiles of Re-WF. Notes: Standard conditions : a=2g, b=5%, c=25+25 g/L, d=20 g/L liquor ratio 1:50

HMJGBP_2019_v47n2_163_f0002.png 이미지

Fig. 2. Color yield of the dyed Re-WF by addition level of reactive dyes.

HMJGBP_2019_v47n2_163_f0003.png 이미지

Fig. 3. Changes in color difference of dyed Re-WF by UV radiation time and addition level of reactive dyes.

HMJGBP_2019_v47n2_163_f0004.png 이미지

Fig. 4. Color yield of the dyed Re-WF with reactive dyes by addition level of sodium sulfate.

HMJGBP_2019_v47n2_163_f0005.png 이미지

Fig. 5. Color yield of the dyed Re-WF with reactive dyes by addition level of sodium carbonate.

HMJGBP_2019_v47n2_163_f0006.png 이미지

Fig. 6. Color yield of the dyed Re-WF with reactive dyes according to dyeing temperature.

HMJGBP_2019_v47n2_163_f0007.png 이미지

Fig. 7. Comparison of ΔE by treatment process (Washing, Soaping and Fixation) for the dyed Re-WF with reactive dyes. Notes : W : Water washing, S : Soaping, F : Fixation

Table 1. Kinds and molecular weight of used dyes

HMJGBP_2019_v47n2_163_t0001.png 이미지

Table 2. Color changes of the dyed Re-WF by addition level of reactive dyes

HMJGBP_2019_v47n2_163_t0002.png 이미지

Table 3. pH of each dyeing process

HMJGBP_2019_v47n2_163_t0003.png 이미지

참고문헌

  1. Bhatti, I.A., Zia, K.M. Ali, Z., Zuber, M., Rehman, F. 2012. Modification of cellulosic fibers to enhance their dyeability using UV-irradiation. Carbohydrate Polymers 89: 783-787. https://doi.org/10.1016/j.carbpol.2012.04.010
  2. CIBA-GEIGY. 1990. Dying of reactive dyes. Journal of the Korean Society of Dyers and Finishers 2(1): 44-67.
  3. Hidayat, W., Qi Y., Jang, J.H., Park, B.H., Banuwa, I.S. Febrianto, F., Kim, N.H. 2017. Color change and consumer preferences towards color of heat-treated Korean white pine and royal paulownia woods. Journal of the Korean Wood Science and Technology 45(2): 213-222. https://doi.org/10.5658/WOOD.2017.45.2.213
  4. Jung, Y.J., Lee, Y.H., Park, S.M. and Kim, K.H. 1994. A study on dyeing properties of cationic agent treated cotton fiber with reactive dye. Journal of the Korean Society of Dyers and Finishers 6(4): 46-53.
  5. Ju, S.G., Roh, J.K. 2017. Manufacture of Dyed Recycling Woody fiber Using Waste MDF Journal of the Korean Wood Science and Technology 45(3): 297-307. https://doi.org/10.5658/WOOD.2017.45.3.297
  6. Khatri, M., Ahmed, F., Jatoi, A.W., Kim, I.S., Mahar, R.B., Khatri, Z. 2016. Ultrasonic dyeing of cellulose nanofibers. Ultrasonics Sonochemistry 31: 350-354. https://doi.org/10.1016/j.ultsonch.2016.01.020
  7. Kim, M.R. Lee, H.J. Lee, J.J., 2010.The Effect of Sodium Sulfate in Liquid or Solid Form on Reactive Dyeing and Fastness Properties of Cellulose Knitted Fabric. Textile Coloration and Finishing 22(4): 341-348. https://doi.org/10.5764/TCF.2010.22.4.341
  8. Koh, J.S., Kim, I.S., Kim, S.S. Shim, W.S., Kim, J.P. Kwak, S.Y. Chun, S.W., Kwon, Y.K. 2004. Dyeing Properties of Novel Regenerated Cellulosic Fibers. Journal of Applied Polymer Science 91(6): 3481-3488. https://doi.org/10.1002/app.13551
  9. Koh, J.S., Kim, I.S., Kim, S.S. Shim, W.S., Kim, J.P., 2004. Dyeing properties of Bis-functional reactive dyes on a novel regenerated cellulosic fiber. Fibers and Polymers 5(1): 44-51. https://doi.org/10.1007/BF02875494
  10. Koh, J.S., Kim, I.S., Kim, S.S. Shim, W.S., Kim, J.P. 2005. Reactive dyeing properties of novel regenerated cellulosic fibres. Dyes and Pigments 64(1): 9-16. https://doi.org/10.1016/j.dyepig.2004.03.015
  11. Larik, S.A., Khatr, A. Ali, S. Kim. S.H. 2015. Batchwise dyeing of bamboo cellulose fabric with reactive dye using ultrasonic energy. Ultrasonics Sonochemistry 24: 178-183. https://doi.org/10.1016/j.ultsonch.2014.12.016
  12. Lee, J.S., Choi, G.S. 2018. Development of coloring method of didecyldimethylammonium chloride (DDAC) in wood treated with alkaline copper quaternary (ACQ) preservative. Journal of the Korean Wood Science and Technology 46(3): 253-259. https://doi.org/10.5658/WOOD.2018.46.3.253
  13. Lee, S.K., Jo, H.J., Kim, Y.G., Lee, H.J., Kang, H.Y. 2006. Analysis of dyeing components from Neolitsea sericea Koidz bark. Journal of the Korean Wood Science and Technology 34(3): 64-72.
  14. Moon. S.O., Kim, C.H., Kim, G.Y., Jung, H.G., Shin, T.G., Kim, J.G., Park, C.Y. 2007. Application of natural dyes for developing colored wood furniture (2) -Color variation by treatment methods of natural dyes-. Journal of the Korean Wood Science and Technology 35(3): 79-87.
  15. Yoon, K.J., Eom, C.D., Park, J.H., Kim, H.Y., Choi, I.G., Lee,J.J., Yeo., H.M. 2009. Color control and durability improvement of yellow polar (Liriodendron tulipifera) by heat treatments. Journal of the Korean Wood Science and Technology 37(6): 487-496.