DOI QR코드

DOI QR Code

Numerical simulations of progression of damage in concrete embedded chemical anchors

  • Sasmal, S. (CSIR-Structural Engineering Research Centre, CSIR Campus) ;
  • Thiyagarajan, R. (CSIR-Structural Engineering Research Centre, CSIR Campus) ;
  • Lieberum, K.H. (Institute of Construction and Building Materials, Technische Universitat Darmstadt) ;
  • Koenders, E.A.B. (Institute of Construction and Building Materials, Technische Universitat Darmstadt)
  • Received : 2018.02.08
  • Accepted : 2018.10.11
  • Published : 2018.10.25

Abstract

In this paper, the performance of post-installed adhesive bonded anchor embedded in concrete is assessed using numerical simulations. This study aims at studying the influence of parameters on the performance of a chemically bonded anchorage system. Non-linear finite element modelling and simulations are carried out by properly using the material properties and phenomenon. Materials parameters such as characteristic length, fracture energy, damage criteria, tension retention and crack width of concrete and interface characteristics are carefully assigned so as to obtain a most realistic behaviour of the chemical anchor system. The peak strength of two different anchor systems obtained from present numerical studies is validated against experimental results. Furthermore, validated numerical models are used to study the load transferring mechanism and damage progression characteristics of various anchors systems where strength of concrete, strength of epoxy, and geometry and disposition of anchors are the parameters. The process of development of strain in concrete adjacent to the anchor and energy dissipated during the course of damage progression are analysed. Results show that the performance of the considered anchorage system is, though a combined effect of material and geometric parameters, but a clear distinction could be made on the parameters to achieve a desired performance based on strength, slip, strain development or dissipated energy. Inspite the increase in anchor capacity with increase in concrete strength, it brings some undesirable performance as well. Furthermore, the pullout capacity of the chemical anchor system increases with a decrease in disparity among the strength of concrete and epoxy.

Keywords

References

  1. ATENA Theory Manual (2006), ATENA Program Documentation-Part 1: Theory, Revision 09/2006, Cervenka Consulting, Predvoje 22, Czech Republic.
  2. Bajer, M. and Barnat, J. (2012), "The glue-concrete interface of bonded anchors", Constr. Build. Mater., 34, 267-274. https://doi.org/10.1016/j.conbuildmat.2012.02.030
  3. Barnat, J., Bajer, M. and Vyhnankova, M. (2012), "Bond strength of chemical anchor in high-strength concrete", Procedia Eng., 40, 38-43. https://doi.org/10.1016/j.proeng.2012.07.052
  4. Bazant, Z.P. and Oh, B.H. (1983), "Crack band theory for fracture of concrete", Mater. Struct. RILEM, 16(93), 155-177.
  5. Bouazaoui, L. and Li, A. (2008), "Analysis of steel/concrete interfacial shear stress by means of pull out test", Int. J. Adhes. Adhes., 28, 101-108. https://doi.org/10.1016/j.ijadhadh.2007.02.006
  6. Cattaneo, S. and Muciaccia, G. (2016), "Adhesive anchors in high performance concrete", Mater. Struct., 49, 2689-2700. https://doi.org/10.1617/s11527-015-0677-4
  7. Colak, A. (2001), "Parametric study of factors affecting the pullout strength of steel rods bonded into precast concrete panels", Int. J. Adhes. Adhes., 21,487-493. https://doi.org/10.1016/S0143-7496(01)00028-8
  8. De Matteis, G., Formisano, A. and Mazzolani, F.M. (2009) "An innovative methodology for seismic retrofitting of existing RC buildings by metal shear panels", Earthq. Eng. Struct. Dyn., 38, 61-78. https://doi.org/10.1002/eqe.841
  9. Delhomme, F., Roure, T., Arrieta, B. and Limam, A. (2015), "Static and cyclic pullout of cast in place headed and bonded anchors with large embedment depths in cracked concrete", Nucl. Eng. Des., 287, 139-150 https://doi.org/10.1016/j.nucengdes.2015.03.012
  10. Delhomme, F., Roure, T., Arrieta, B. and Limam, A. (2016), "Pullout behavior of cast in place headed and bonded anchors with different embedment depths", Mater. Struct., 49, 1843-1859 https://doi.org/10.1617/s11527-015-0616-4
  11. Dudek, D. and Kadela, M. (2016), "Pull-out strength of resin anchors in non-cracked and cracked concrete and masonry substrates", Procedia Eng., 161, 864-867. https://doi.org/10.1016/j.proeng.2016.08.734
  12. Eligehausen, R. and Appl, J. (2007), "Behavior and design of fastening with bonded anchors: Numerical analysis and experimental verification", VI International Conference on Fracture Mechanics and Concrete Structure.
  13. Eligehausen, R., Cook, R. and Appl, J. (2006), "Behaviour and design of adhesive bonded anchors", ACI Struct. J., 103(6), 822.
  14. Eligehausen, R., Genesio, G. and Ozbolt, J. (2009), "3D analysis of seismic response of RC beam-column exterior joints before and after retrofit", Concrete Repair, Rehabilitation and Retrofitting II, Eds. Alexander et al. Taylor & Francis Group, London.
  15. Eligehausen, R., Mallee, R. and Silva, J.F. (2006), Anchorage in Concrete Construction, Errnst & Sohn, John Wiley & Sons, Germany.
  16. Elwood, K.J., Marder, K., Pampanin, S., Ramirez, A.C., Kral, M., Smith, P., Cattanach, A. and Stannard, M. (2016), "Draft framework for assessing residual capacity of earthquakedamaged concrete buildings", 2016 New Zealand Society of Earthquake Engineering Conference on Reducing Risk Raising Resilience, Christchurch.
  17. Epackachi, S., Esmail, O., Mirghaderi, S. and Behbahani, A. (2015), "Behavior of adhesive bonded anchor under tension and shear loads", J. Constr. Steel Res., 134, 269-280.
  18. Flint, M.M., Dhulipala, L.N.S., Shahtaheri, Y., Tahir, H., Ladipo, T., Eatherton, M.R., Irish, J.L., Olgun, C.G., Reichard, G., Rodriguez-Marek, A., Zobel, C., Leon, R.T. and de la Garza, J.M. (2016), "Developing a decision framework for multihazard design of resilient, sustainable buildings", 1st International Conference on Natural Hazards & Infrastructure, Chania, Greece, June.
  19. Gurbuz, T. and Ilki, A. (2011), "Pullout performance of fully and partially bonded retrofit anchors in low-strength concrete", ACI Struct. J., 108(1), 61-70.
  20. Hordijik, D.A. (1991), "Local approach to fatigue of concrete", PhD Thesis, Delft University of Technology.
  21. Jalalifar, H. (2006), "A new approach in determining the load transfer mechanism in fully grouted bolts", PhD Thesis, University of Wollongong.
  22. Kabir, M. and Islam, M. (2014), "Bond stress behaviour between concrete and steel rebar: Critical investigation of pullout test via Finite Element Modelling", Int. J. Civil Struct. Eng., 5(1), 80-90.
  23. Kim, N., Park, J. and Kim, S. (2007), "Numerical simulation of ground anchors", Comput. Geotech., 34, 498-507. https://doi.org/10.1016/j.compgeo.2006.09.002
  24. Li, Y., Patil, S., Winkler, B. and Neumar, T. (2013), "Numerical analysis of screw anchor for concrete", VIII International Conference on Fracture Mechanics and Concrete Structure.
  25. Menetrey, P. and Willam, K.J. (1995), "Triaxial failure criterion for concrete and its generalization", ACI Struct. J., 92(3), 311-318.
  26. Pampanin, S., Christopoulos, C. and Chen, T.H. (2006), "Development and validation of a metallic haunch seismic retrofit solution for existing under-designed RC frame buildings", Earthq. Eng. Struct. Dyn., 35, 1739-1766. https://doi.org/10.1002/eqe.600
  27. Remmel, G. (1994), Zum Zug- und Schubtragverhalten von Bauteilen aus hochfestem Beton, Deutscher Ausschuss fur Stahlbeton, Beuth Verlag, Berlin, Germany.
  28. Rizzo, P., Spada, A., Degala, S. and Giambanco, G. (2010) "Acoustic emission monitoring of chemically bonded anchors", J. Non-Destruct. Eval., 29, 49-61 https://doi.org/10.1007/s10921-010-0065-5
  29. Rots, J.G. and Blaauwendraad, J. (1989), "Crack model for concrete: Discrete or smeared? Fixed, multi-directional or rotating?", Heron, 34(1), 1-59.
  30. Sasmal, S. and Nath, D. (2016), "Evaluation of performance of non-invasive upgrade strategy for beam-column subassemblages of poorly designed structures under seismic type loading", Earthq. Eng. Struct. Dyn, 45, 1817-1835. https://doi.org/10.1002/eqe.2730
  31. Sasmal, S., Novak, B. and Ramanjaneyulu, K. (2011), "Numerical analysis of fiber composite-steel plate upgraded beam-column sub-assemblages under cyclic loading", J. Compos. Struct., 93(2), 599-610. https://doi.org/10.1016/j.compstruct.2010.08.019
  32. Sharbatdar, M.K., Kheyroddin, A. and Emami, E. (2012) "Cyclic performance of retrofitted reinforced concrete beam-column joints using steel prop", Constr. Build. Mater., 36, 287-294. https://doi.org/10.1016/j.conbuildmat.2012.04.115
  33. Spada, A., Giambanco, G. and Rizzo, P. (2011), "Elastoplastic damaging model for adhesive anchor systems. 1: Theoretical formulation and numerical implementation", J. Eng. Mech., 137(12), 854-861. https://doi.org/10.1061/(ASCE)EM.1943-7889.0000287
  34. Tang, C.W. (2015) "Local bond stress-slip behaviour of reinforcing bars embedded in lightweight concrete", Comput. Concrete, 16(3), 449-466 https://doi.org/10.12989/cac.2015.16.3.449
  35. Test report Nr. 190.01.07 (2008), Institute of Construction and Building Materials, TU Darmstadt, Germany.
  36. Wu, Z., Yang, S., Hu, X. and Zheng, J. (2007), "Analytical method for pullout of anchor from anchor-mortar-concrete anchorage system due to shear failure of mortar", J. Eng. Mech., 133(12), 1352-1369. https://doi.org/10.1061/(ASCE)0733-9399(2007)133:12(1352)
  37. Xu, C., Heping, C., Bin, L. and Fangfanf, Z. (2011), "Modelling of anchor bolt pullout in concrete based on heterogeneous assumption", Nucl. Eng. Des., 241, 1345-1351. https://doi.org/10.1016/j.nucengdes.2011.01.025
  38. Yang, S., Wu, Z., Hu, X. and Zheng, J. (2008), "Theoretical analysis on pullout of anchor from anchor-mortar-concrete anchorage system", Eng. Fract. Mech., 75, 961-985. https://doi.org/10.1016/j.engfracmech.2007.05.004
  39. Yilmaz, S., Ozen, M. and Yardim, Y. (2013), "Tensile behaviour of post installed chemical anchors embedded in low strength concrete", Constr. Build. Mater., 47, 861-866. https://doi.org/10.1016/j.conbuildmat.2013.05.032

Cited by

  1. On the strength of chemical anchors vol.1129, pp.1, 2018, https://doi.org/10.1088/1757-899x/1129/1/012023