Advances in concrete construction

  • 제6권5호
  • /
  • Pages.545-560
  • /
  • 2018
  • /
  • 2287-5301(pISSN)
  • /
  • 2287-531X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Copper or ferrous slag as substitutes for fine aggregates in concrete

  • Thomas, Job (Department of Civil Engineering, Cochin University of Science and Technology) ;
  • Thaickavil, Nassif N. (Department of Civil Engineering, Cochin University of Science and Technology) ;
  • Abraham, Mathews P. (Department of Civil Engineering, Cochin University of Science and Technology)
  • 투고 : 2018.01.07
  • 심사 : 2018.10.25
  • 발행 : 2018.10.25
⟨ 이전 논문 다음 논문 ⟩

초록

The ever-increasing cost of natural sand and the environmental impacts of extracting manufactured sand (quarry sand) calls for exploring the potential to use alternative materials as fine aggregates in concrete. Copper slag and ferrous slag are industrial by products obtained from the smelting process of copper and iron respectively. A large quantity of copper slag and ferrous slag end up being disposed as waste in landfills and this poses a serious threat to the environment. Copper slag and ferrous slag have similar physical and chemical properties as natural sand and also exhibit pozzolanic activity. This paper studies the technical feasibility of industrial by-products such as copper slag and ferrous slag to replace the fine aggregate in concrete by evaluating the workability, strength and durability characteristics of concrete. The test results indicate that the strength properties are not affected by 40% or 100% replacement of quarry sand with iron slag or copper slag. However, 40% replacement of quarry sand with iron slag or copper slag in concrete is recommended considering the durability aspects of concrete.

키워드

참고문헌

  1. ACI 211.1-91 (2002), Standard Practice for Selecting Proportions for Normal, Heavyweight, and Mass Concrete, Michigan, USA.
  2. Al-Jabri, K.S. and Hisada, M. (2009), "Copper slag as sand replacement for high performance concrete", Cement Concete Compos., 31, 483-488. https://doi.org/10.1016/j.cemconcomp.2009.04.007
  3. Al-Jabri, K.S., Al-Saidy, A.H. and Taha, R. (2011), "Effect of copper slag as a fine aggregate on the properties of cement mortars and concrete", Const. Build. Mater., 25, 933-938. https://doi.org/10.1016/j.conbuildmat.2010.06.090
  4. Ashish, K.D., Singh, B. and Verma, S.K. (2016), "The effect of attack of chloride and sulphate on ground granulated blast furnace slag concrete", Adv. Concrete Constr., 4(2), 107-121. https://doi.org/10.12989/acc.2016.4.2.107
  5. ASTM C1202 (2010), Standard Test Method for Electrical Indication of Concrete's Ability to Resist Chloride Ion Penetration, American Society for Testing and Materials, Pennsylvania, USA.
  6. ASTM C267 (2012), Standard Test Methods for Chemical Resistance of Mortars, Grouts, and Monolithic Surfacings and Polymer Concretes, American Society for Testing and Materials, Pennsylvania, USA.
  7. ASTM C452 (2015), Standard Test Method for Potential Expansion of Portland-Cement Mortars Exposed to Sulfate, American Society for Testing and Materials, Pennsylvania, USA.
  8. Basheer, P.A.M. (2001), "Near-surface moisture gradients and in situ permeation tests", Constr. Build. Mater., 15(2), 105-114. https://doi.org/10.1016/S0950-0618(00)00059-3
  9. Brindha, D. and Nagan, S. (2010), "Utilization of copper slag as a partial replacement of fine aggregate", Intl. J. Earth Sci. Eng., 3(4), 579-585.
  10. Dash, M.K., Patro, S.K. and Rath, A.K. (2016), "Sustainable use of industrial-waste as partial replacement of fine aggregate for preparation of concrete-A review", Intl. J. Sustain. Built Environ., 5, 484-516 . https://doi.org/10.1016/j.ijsbe.2016.04.006
  11. Devi, V.S. and Gnanavel, B.S. (2014), "Properties of concrete manufactured using steel slag", Procedia Eng., 97, 95-104. https://doi.org/10.1016/j.proeng.2014.12.229
  12. Dhir, R.K., de Brito, J., Mangabhai, R. and Lye, C.Q. (2017), "Sustainable Construction Materials-Copper Slag, Woodhead Publishing, Cambridge.
  13. Gorai, B. and Jana, R.K. (2002), "Characteristics and utilization of copper slag", Resour. Conserv. Recyc., 39(4), 299-313. https://doi.org/10.1016/S0921-3449(02)00171-4
  14. Hiraskar, K.G. and Patil, C. (2013), "Use of blast furnace slag aggregate in concrete", Int. J. Sci. Eng. Res., 4 (5), 95-98.
  15. Indian Bureau of Mines (2015), Indian Minerals Yearbook (Part- II: Metals & Alloys, 54th Edition, Nagpur, India.
  16. IS: 10262 (2009), Concrete Mix Proportioning- Guidelines, Bureau of Indian Standards, New Delhi, India.
  17. IS: 1199 (1959), Methods of Sampling and Analysis of Concrete, Bureau of Indian Standards, New Delhi, India.
  18. IS: 12269 (1987), Ordinary Portland Cement 53 Grade- Specification, Bureau of Indian Standards, New Delhi, India.
  19. IS: 1727 (1967), Method of Test for Pozzolanic Materials, Bureau of Indian Standards, New Delhi, India.
  20. IS: 2386 Part III (1963), Methods of Test for Aggregates for Concrete, Part III: Specific Gravity, Density, Voids, Absorption and Bulking, Bureau of Indian Standards, New Delhi, India.
  21. IS: 383 (2016), Coarse and Fine Aggregate for Concrete- Specification, Bureau of Indian Standards, New Delhi, India.
  22. IS: 516 (1959), Methods of Test for Strength of Concrete, Bureau of Indian Standards, New Delhi, India.
  23. Kahjuria, C. and Siddique, R. (2014), "Use of iron slag as partial replacement of sand to concrete", Int. J. Sci. Eng. Technol. Res., 3(6), 1877-1880.
  24. Mavroulidou, M. (2017), "Mechanical properties and durability of concrete with water cooled copper slag aggregate", Waste Biomass Valor, 8, 1841-1854. https://doi.org/10.1007/s12649-016-9819-3
  25. Patra, R.K. and Mukharjee, B.B. (2016), "Fresh and hardened properties of concrete incorporating ground granulated blast furnace slag-A review", Adv. Concrete Constr., 4(4), 283-303. https://doi.org/10.12989/acc.2016.4.4.283
  26. Patra, R.K. and Mukharjee, B.B. (2017), "Properties of concrete incorporating granulated blast furnace slag as fine aggregate", Adv. Concrete Constr., 5(5), 437-450.
  27. Thomas, J. (2015), Concrete Technology, Cengage Learning, Delhi, India.
  28. UNI 9944 (1994), "Corrosion and protection of reinforcing steel in concrete-Determination of the carbonation depth and of the chlorides penetration profile in concrete", Ente Nazionale Italiano di Unificazione, Milan, Italy.

피인용 문헌

  1. Properties of high performance heavyweight concrete mixtures containing different types of coarse aggregates vol.12, pp.1, 2021, https://doi.org/10.12989/acc.2021.12.1.075