Steel and Composite Structures

  • 제24권4호
  • /
  • Pages.383-390
  • /
  • 2017
  • /
  • 1229-9367(pISSN)
  • /
  • 1598-6233(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Behaviour of carbon fiber reinforced polymer strengthened tubular joints

  • Prashob, P.S. (Department of Civil Engineering, National Institute of Technology Calicut) ;
  • Shashikala, A P. (Department of Civil Engineering, National Institute of Technology Calicut) ;
  • Somasundaran, T.P. (Department of Civil Engineering, National Institute of Technology Calicut)
  • 투고 : 2017.02.16
  • 심사 : 2017.04.02
  • 발행 : 2017.07.20
⟨ 이전 논문 다음 논문 ⟩

초록

This paper highlights the experimental and numerical investigations performed on a tubular T-joint fabricated from circular hollow sections under axial compressive loads applied at the brace. Tests were performed on a reference joint and the joint wrapped with Carbon Fiber Reinforced Polymer (CFRP). The Nitowrap EP carbon fiber with Nitowrap 410 resin serve as a composite material is used for wrapping the T-joint. Schematic diagram of the fabricated tubular joint for the experimental test setup, along with the experimental and numerical results are presented. After performing these experiments, it has been demonstrated that the joint wrapped with CFRP has a better strength and lesser deflection than a reference joint. Finite element analysis carried out in Ansys reveals that the results were in good correlation with the experimental values.

키워드

참고문헌

  1. Aguilera, J. and Fam, A. (2013), "Retrofitting tubular steel T-joints subjected to axial compression in chord and brace members using bonded FRP plates or through-wall steel bolts", Eng. Struct., 48, 602-610. https://doi.org/10.1016/j.engstruct.2012.09.018
  2. Al-saidy, A.H., Klaiber, F.W. and Wipf, T.J. (2004), "Repair of steel composite beams with carbon fiber-reinforced polymer plates", J. Compos. Constr., 8(2), 163-172. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:2(163)
  3. Ansys inc. (2009), http://www.ansys.com
  4. ASTM A106/A106M (2016), Standard Specification for Seamless Carbon Steel Pipe for High-Temperature Service; American Society for Testing and Materials, PA, USA.
  5. ASTM D3039/D3039M (2005), Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials; American Society for Testing and Materials, PA, USA.
  6. ASTM D3518/D3518M (2016), Standard Test Method for In-Plane Shear Response of Polymer Matrix Composite Materials by Tensile Test of a ${\pm}45^{\circ}$ Laminate; American Society for Testing and Materials, PA, USA.
  7. ASTM D5379/D5379M (2016), Standard Test Method for Shear Properties of Composite Materials by the V-Notched ASTM D5379/D5379M; American Society for Testing and Materials, PA, USA.
  8. ASTM E8/E8M (2016), Standard Test Methods for Tension Testing of Metallic Materials; American Society for Testing and Materials, PA, USA.
  9. Fawzia, S., Al-Mahaidi, R., Zhao, X.L. and Rizkalla, S. (2007), "Strengthening of circular hollow steel tubular sections using high modulus CFRP sheets", Constr. Build. Mater., 21(4), 839-845. https://doi.org/10.1016/j.conbuildmat.2006.06.014
  10. Ghafoori, E., Schumacher, A. and Motavalli, M. (2012), "Fatigue behavior of notched steel beams reinforced with bonded CFRP plates: Determination of prestressing level for crack arrest", Eng. Struct., 45, 270-283. https://doi.org/10.1016/j.engstruct.2012.06.047
  11. Haedir, J., Bambach, M.R., Zhao, X.L. and Grzebieta, R.H. (2009), "Strength of circular hollow sections (CHS) tubular beams externally reinforced by carbon FRP sheets in pure bending", Thin-Wall. Struct., 47(10), 1136-1147. https://doi.org/10.1016/j.tws.2008.10.017
  12. Jones, S.C. and Civjan, S.A. (2003), "Application of fiber reinforced polymer overlays to extend steel fatigue life", J. Compos. Constr., 7(4), 331-338. https://doi.org/10.1061/(ASCE)1090-0268(2003)7:4(331)
  13. Keykha, A.H. (2016), "CFRP strengthening of steel columns subjected to eccentric compression loading", Steel Compos. Struct., Int. J., 23(1), 87-94.
  14. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2013a), "Detail investigation on un-stiffened T/Y tubular joints behavior under axial compressive loads", J. Constr. Steel Res., 80, 91-99. https://doi.org/10.1016/j.jcsr.2012.09.016
  15. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2013b), "Numerical investigation of FRP-strengthened tubular T-joints under axial compressive loads", Compos. Struct., 100, 71-78. https://doi.org/10.1016/j.compstruct.2012.12.020
  16. Lesani, M., Bahaari, M.R. and Shokrieh, M.M. (2014), "Experimental investigation of FRP-strengthened tubular Tjoints under axial compressive loads", Constr. Build. Mater., 53, 243-252. https://doi.org/10.1016/j.conbuildmat.2013.11.097
  17. Parashar, A. and Mertiny, P. (2012), "Adhesively bonded composite tubular joints: Review", Int. J. Adhesion Adhesives, 38, 58-68. https://doi.org/10.1016/j.ijadhadh.2012.05.004
  18. Seica, M.V. and Packer, J.A. (2007), "FRP materials for the rehabilitation of tubular steel structures, for underwater applications", Compos. Struct., 80(3), 440-450. https://doi.org/10.1016/j.compstruct.2006.05.029
  19. SMAW (2013), Guidelines for Shielded Metal Arc Welding; Appleton, WI 54914, USA.
  20. Tavakkolizadeh, M. and Saadatmanesh, H. (2003), "Fatigue strength of steel girders strengthened with carbon fiber reinforced polymer patch", J. Struct. Eng., 129(2), 186-196. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:2(186)
  21. Teng, J.G. and Hu, Y.M. (2007), "Behaviour of FRP-jacketed circular steel tubes and cylindrical shells under axial compression", Constr. Build. Mater., 21(4), 827-838. https://doi.org/10.1016/j.conbuildmat.2006.06.016
  22. Thandavamoorthy, T.S. (2004), "Reserve capacity of fatigue damaged internally ring stiffened tubular joints", Steel Compos. Struct., Int. J., 4(2), 149-167. https://doi.org/10.12989/scs.2004.4.2.149
  23. Zhao, X.L. and Zhang, L. (2011), "State-of-the-art review on FRP strengthened steel structures", Eng. Struct., 29(8), 1808-1823. https://doi.org/10.1016/j.engstruct.2006.10.006

피인용 문헌

  1. Investigating loading rate and fibre densities influence on SRG - concrete bond behaviour vol.34, pp.6, 2020, https://doi.org/10.12989/scs.2020.34.6.877