DOI QR코드

DOI QR Code

The effect of prolonged storage and disinfection on the dimensional stability of 5 vinyl polyether silicone impression materials

  • Nassar, Usama (Faculty of Medicine and Dentistry, Department of Dentistry, University of Alberta) ;
  • Flores-Mir, Carlos (Faculty of Medicine and Dentistry, Department of Dentistry, University of Alberta) ;
  • Heo, Giseon (Faculty of Medicine and Dentistry, Department of Dentistry, University of Alberta) ;
  • Torrealba, Ysidora (Faculty of Medicine and Dentistry, Department of Dentistry, University of Alberta)
  • Received : 2016.08.23
  • Accepted : 2017.03.21
  • Published : 2017.06.30

Abstract

PURPOSE. Vinyl polyether silicone (VPES) has a different composition from other elastomeric impression materials as it combines vinyl polysiloxane (VPS) and polyether (PE). Therefore, it is important to study its properties and behavior under different test conditions. This study investigated the dimensional stability of 5 VPES consistencies when stored for up to 2 weeks, with and without using a standard disinfection procedure. MATERIALS AND METHODS. 40 discs of each VPES consistency (total 200) were made using a stainless steel die and ring as described by ANSI /ADA specification No. 19. 20 discs of each material were immersed in a 2.5% buffered glutaraldehyde solution for 30 minutes. Dimensional stability measurements were calculated immediately after fabrication and repeated on the same discs after 7 and 14 days of storage. The data was analyzed using two-way ANOVA with a significance level set at ${\alpha}=0.05$. RESULTS. The discs mean contraction was below 0.5% at all test times ranging from $0.200{\pm}0.014$ to $0.325{\pm}0.007$. Repeated measures ANOVA showed a statistically significant difference after 2-week storage between the disinfected and non-disinfected groups (P < .001). Although there was no statistically significant difference between the materials at the time of fabrication, the contraction of the materials increased with storage for 1 and 2 weeks. CONCLUSION. The dimensional changes of VPES impression discs after disinfection and prolonged storage complied with ANSI/ADA standard. The tested VPES impression materials were dimensionally stable for clinical use after disinfection for 30 minutes in glutaraldehyde and storage for up to 2 weeks.

Keywords

References

  1. Sakaguchi RL, Powers JM. Craig's restorative dental materials. 13th ed. Philadelphia: Mosby Elsevier; 2012. p. 293.
  2. Kanehira M, Finger WJ, Endo T. Volatilization of components from and water absorption of polyether impressions. J Dent 2006;34:134-8. https://doi.org/10.1016/j.jdent.2005.05.003
  3. Walker MP, Petrie CS, Haj-Ali R, Spencer P, Dumas C, Williams K. Moisture effect on polyether and polyvinylsiloxane dimensional accuracy and detail reproduction. J Prosthodont 2005; 14:158-63. https://doi.org/10.1111/j.1532-849X.2005.04024.x
  4. Petrie CS, Walker MP, O'mahony AM, Spencer P. Dimensional accuracy and surface detail reproduction of two hydrophilic vinyl polysiloxane impression materials tested under dry, moist, and wet conditions. J Prosthet Dent 2003;90:365-72. https://doi.org/10.1016/S0022-3913(03)00515-8
  5. Corso M, Abanomy A, Di Canzio J, Zurakowski D, Morgano SM. The effect of temperature changes on the dimensional stability of polyvinyl siloxane and polyether impression materials. J Prosthet Dent 1998;79:626-31. https://doi.org/10.1016/S0022-3913(98)70068-X
  6. Yilmaz H, Aydin C, Gul B, Yilmaz C, Semiz M. Effect of disinfection on the dimensional stability of polyether impression materials. J Prosthodont 2007;16:473-9. https://doi.org/10.1111/j.1532-849X.2007.00235.x
  7. Kern M, Rathmer RM, Strub JR. Three-dimensional investigation of the accuracy of impression materials after disinfection. J Prosthet Dent 1993;70:449-56. https://doi.org/10.1016/0022-3913(93)90084-2
  8. Jagger DC, Vowles RW, McNally L, Davis F, O'Sullivan DJ. The effect of a range of disinfectants on the dimensional accuracy and stability of some impression materials. Eur J Prosthodont Restor Dent 2007;15:23-8.
  9. Melilli D, Rallo A, Cassaro A, Pizzo G. The effect of immersion disinfection procedures on dimensional stability of two elastomeric impression materials. J Oral Sci 2008;50:441-6. https://doi.org/10.2334/josnusd.50.441
  10. Wadhwani CP, Johnson GH, Lepe X, Raigrodski AJ. ccuracy of newly formulated fast-setting elastomeric impression materials. J Prosthet Dent 2005;93:530-9. https://doi.org/10.1016/j.prosdent.2005.03.007
  11. Adabo GL, Zanarotti E, Fonseca RG, Cruz CA. Effect of disinfectant agents on dimensional stability of elastomeric impression materials. J Prosthet Dent 1999;81:621-4. https://doi.org/10.1016/S0022-3913(99)70219-2
  12. Davis BA, Powers JM. Effect of immersion disinfection on properties of impression materials. J Prosthodont 1994;3:31-4. https://doi.org/10.1111/j.1532-849X.1994.tb00122.x
  13. Rios MP, Morgano SM, Stein RS, Rose L. Effects of chemical disinfectant solutions on the stability and accuracy of the dental impression complex. J Prosthet Dent 1996;76:356-62. https://doi.org/10.1016/S0022-3913(96)90538-7
  14. Lepe X, Johnson GH, Berg JC, Aw TC, Stroh GS. Wettability, imbibition, and mass change of disinfected low-viscosity impression materials. J Prosthet Dent 2002;88:268-76. https://doi.org/10.1067/mpr.2002.128757
  15. Langenwalter EM, Aquilino SA, Turner KA. The dimensional stability of elastomeric impression materials following disinfection. J Prosthet Dent 1990;63:270-6. https://doi.org/10.1016/0022-3913(90)90193-G
  16. Matyas J, Dao N, Caputo AA, Lucatorto FM. Effects of disinfectants on dimensional accuracy of impression materials. J Prosthet Dent 1990;64:25-31. https://doi.org/10.1016/0022-3913(90)90148-6
  17. Thouati A, Deveaux E, Iost A, Behin P. Dimensional stability of seven elastomeric impression materials immersed in disinfectants. J Prosthet Dent 1996;76:8-14. https://doi.org/10.1016/S0022-3913(96)90338-8
  18. Lepe X, Johnson GH. Accuracy of polyether and addition silicone after long-term immersion disinfection. J Prosthet Dent 1997;78:245-9. https://doi.org/10.1016/S0022-3913(97)70021-0
  19. Walker MP, Rondeau M, Petrie C, Tasca A, Williams K. Surface quality and long-term dimensional stability of current elastomeric impression materials after disinfection. J Prosthodont 2007;16:343-51. https://doi.org/10.1111/j.1532-849X.2007.00206.x
  20. Donovan TE, Chee WW. A review of contemporary impression materials and techniques. Dent Clin North Am 2004;48: 445-70. https://doi.org/10.1016/j.cden.2003.12.014
  21. Lacy AM, Fukui H, Bellman T, Jendresen MD. Timedependent accuracy of elastomer impression materials. Part II: Polyether, polysulfides, and polyvinylsiloxane. J Prosthet Dent 1981;45:329-33. https://doi.org/10.1016/0022-3913(81)90400-5
  22. Thongthammachat S, Moore BK, Barco MT 2nd, Hovijitra S, Brown DT, Andres CJ. Dimensional accuracy of dental casts: influence of tray material, impression material, and time. J Prosthodont 2002;11:98-108. https://doi.org/10.1053/jopr.2002.125192
  23. Nassar U, Oko A, Adeeb S, El-Rich M, Flores-Mir C. An in vitro study on the dimensional stability of a vinyl polyether silicone impression material over a prolonged storage period. J Prosthet Dent 2013;109:172-8. https://doi.org/10.1016/S0022-3913(13)60038-4
  24. Nassar U, Chow AK. Surface detail reproduction and effect of disinfectant and long-term storage on the dimensional stability of a novel vinyl polyether silicone impression material. J Prosthodont 2015;24:494-8. https://doi.org/10.1111/jopr.12244
  25. American Dental Association Specification no. 19 for Nonaqueous, Elastomeric Dental Impression Materials. J Am Dent Assoc 1977;94:733-41. https://doi.org/10.14219/jada.archive.1977.0334
  26. Owen CP. An investigation into the compatibility of some irreversible hydrocolloid impression materials and dental gypsum products. Part I. Capacity to record grooves on the international standard die. J Oral Rehabil 1986;13:93-103. https://doi.org/10.1111/j.1365-2842.1986.tb01559.x
  27. Lepe X, Johnson GH, Berg JC. Surface characteristics of polyether and addition silicone impression materials after long-term disinfection. J Prosthet Dent 1995;74:181-6. https://doi.org/10.1016/S0022-3913(05)80184-2

Cited by

  1. Effect of Surfosept and Deconex® 53 Disinfectant Agents on the Accuracy and Dimensional Stability of Panasil Dental Impression Materials: An Experimental Study vol.2021, pp.None, 2017, https://doi.org/10.1155/2021/1248531
  2. Dimensional Stability of Elastomeric Impression Material After Disinfection Via Immersion and Microwave Irradiation vol.15, pp.1, 2021, https://doi.org/10.2174/1874210602115010658
  3. Comparative Study of Dimensional Stability and Detail Reproduction of Reformulated and Nonreformulated Elastomeric Impression Materials vol.30, pp.4, 2017, https://doi.org/10.1111/jopr.13248