Journal of the Society of Naval Architects of Korea (대한조선학회논문집)

The Society of Naval Architects of Korea (대한조선학회)
권호 표지
DOI QR코드

DOI QR Code

Development of Doubler Design System for Ship Plate Members Subjected to In-plane Shear and Biaxial Compressive Loads

면내 전단하중과 양축압축하중을 받는 선박 판부재의 이중판 설계시스템 개발

  • Ham, Juh-Hyeok (Department of Mechatronics Engineering, Halla University)
  • 함주혁 (한라대학교 메카트로닉스공학과)
  • Received : 2016.08.28
  • Accepted : 2017.05.21
  • Published : 2017.06.20
Download PDF
⟨ Previous Next ⟩

Abstract

A design system for doubler reinforcement of the ship plate members subjected to in-plane shear and biaxial compressive loads was developed. This design system of doubler reinforcement on ship plate members established by design supporting system and this system was based on the buckling evaluation process of ship plate members for these in-plane loads. Each design parameters were suggested by equations as the form of influence coefficients for the doubler reinforcement subjected to the various in-plane loads including shear load. Strength of doubler plate member reinforced on the plate member could be suggested by the equivalent flat plate thickness after the consideration of corelation equations in the design system of doubler reinforcement. Level of strength recovery of ship plate members for these in-plane loads according to the local reinforcement by doubler could be suggested by use of this design system in the initial repair design stage of shipyards.

Keywords

References

  1. Ham, J.H., 1999. Strength evaluation of doubler plate of ship structure subjected to the longitudinal in-plane compression. Proceedings of the Annual Autumn Meeting, the Society of Naval Architects of Korea, Daejeon, Republic of Korea, 11-12 November 1999.
  2. Ham, J.H., 2001. Strength evaluation of a doubler plate of ship structure subjected to the biaxila in-plane compression. Journal of the Society of Naval Architects of Korea, 38(1), pp.72-85.
  3. Ham, J.H. & Kim, U.N., 1997. The development of advanced buckling strength estimation system. Journal of the Society of Naval Architects of Korea, 34(3), pp.53-60.
  4. Ham, J.H., 2014. Development of slender doubler plate hybrid design system for ship structure subjected to longitudinal in-plane compression. Journal of Ocean Engineering and Technology, 28(1), pp.20-27. https://doi.org/10.5574/KSOE.2014.28.1.020
  5. Ham, J.H., 2016. Development of ship plate member design system reinforced by doubler plate subjected to biaxial in-plane compressive load. Journal of Ocean Engineering and Technology, 30(4), pp.294-302. https://doi.org/10.5574/KSOE.2016.30.4.294
  6. Jastrzebski, T. & Kimiecik, M., 1986. Statistical investigations of the deformations of ship plates (in France). Bulletin de I'Association Technique Maritime et Aeronautique, 86, pp.235-345.
  7. Lasdon, L.S. & Waren, A.D., 1978. Generalized reduced gradient software for lsinearly and nonlinearly constrained problems. in : Greenberg, H.J. (Ed.) Design and implementation of optimization software. Sijthoff and Noordhoff: holland.
  8. Paik, J.K. Ham, J.H. & Kim, U.N., 1992a. A new plate buckling design formula. Journal of the Society of Naval Architects of Japan, 171, pp.559-566.
  9. Paik, J.K. Ham, J.H. & Ko, J.Y., 1992b. A new plate buckling design formula(2nd Report) - On the plasticity correction. Journal of the Society of Naval Architects of Japan, 172, pp.417-425.