Transactions of the Korean Society of Mechanical Engineers B (대한기계학회논문집B)

The Korean Society of Mechanical Engineers (대한기계학회)
권호 표지
DOI QR코드

DOI QR Code

Effects of Port Shape on Steady Flow Characteristics in an SI Engine with Semi-Wedge Combustion Chamber (2) - Velocity Distribution (2)

반 쐐기형 연소실을 채택한 SI 기관에서 포트형상이 정상유동 특성에 미치는 영향 (2) - 유속분포 (2)

  • Yoon, Inkyoung (Graduate school of Energy & Environment, Seoul Nat'l Univ. of Science and Technology) ;
  • Ohm, Inyong (Dept. of Mechanical and automotive Engineering, Seoul Nat'l Univ. of Science and Technology)
  • 윤인경 (서울과학기술대학교 에너지환경전문대학원) ;
  • 엄인용 (서울과학기술대학교 기계.자동차공학과)
  • Received : 2016.08.17
  • Accepted : 2016.12.04
  • Published : 2017.02.01
Download PDF
⟨ Previous Next ⟩

Abstract

This study is the second investigation on the steady flow characteristics of an SI engine with a semi-edge combustion chamber as a function of the port shape with varying evaluation positions. For this purpose, the planar velocity profiles were measured from 1.75B, 1.75 times of bore position apart from the bottom of head, to 6.00B positions using particle - image velocimetry. The flow patterns were examined with both a straight and a helical port. The velocity profiles, streamlines, and centers of swirl were almost the same at the same valve lift regardless of the measuring position, which is quite different from the case of the pent-roof combustion chamber. All the eccentricity values of the straight port were out of distortion criterion 0.15 through the lifts and the position. However, the values of the helical port exceeded the distortion criterion by up to 4 mm lift, but decreased rapidly above the 3.00B position and the 5 mm lift. There always existed a relative offset effect in the evaluation of the swirl coefficient using the PIV method due to the difference of the ideal impulse swirl meter velocity profile assumption, except for the cylinder-center-base estimation that was below 4 mm of the straight port. Finally, it was concluded that taking the center as an evaluation basis and the assumption about the axial velocity profile did not have any qualitative effect on swirl evaluation, but affected the value owing to the detailed profile.

본 논문은 반 쐐기형 연소실에서 포트형상에 따른 정상유동 특성을 비교한 연구의 두 번째로 유동 평가위치의 영향을 고찰한 것이다. 입자영상유속계로 반 쐐기형 연소실에 직선형 포트와 나선형 포트를 적용하여 측정위치를 헤드 밑면부터 하류로 보어의 1,75배 위치 즉 1.75B부터 6배 위치 즉, 6.00B까지 변경하면서 평면유속을 측정하였다. 속도분포 분석 결과 반 쐐기형 연소실을 채택하면 지붕형과 달리 동일 리프트에서 거시적 유속분포와 유선은 스월 거동 중심은 측정위치가 관계없이 거의 일정하다. 직선형 포트에서는 모든 측정위치에서 편심도는 충격식 스월 측정기에서 측정값 왜곡이 발생하는 범위에 들어오고, 나선형 포트에서도 리프트 4mm 이하에서는 모든 측정위치에서 편심의 영향을 무시할 수 없지만, 측정위치가 3.00B 이상이 되면 리프트 5mm 이상에서 편심도가 급격히 감소한다. ISM가정과의 속도분포 차이에 의해 직선형 포트의 리프트 4mm 이하 스월 중심 평가를 제외하고 모든 PIV 평가방법에서 ISM 평가 대비 상대적인 상쇄효과가 있다. 마지막으로 중심 설정과 축 방향 속도분포 가정은 스월 평가에 정성적 영향을 주지 않고, 구체적인 접선속도 분포형태에 따라 절댓값에만 영향을 준다.

Keywords

References

  1. Superflow Corporation, 1976, "Superflow 600 Instructions," Appendix I, Colorado Springs.
  2. Heywood, J. B., 1988, Internal Combustion Engine Fundamentals. Int. edn., McGraw-Hill, pp. 343-345, Singapore.
  3. Stone, R., 1992, Introduction to Internal Combustion Engines. Second edn., McGraw-Hill, pp. 183-185, Hong Kong.
  4. Ohm, I. and Park, C., 2008, "In-Cylinder Intake Flow Characteristics of Helical Port Engines with Wide Valve Angle," Trans. Korean Soc. Mech. Eng. B, Vol. 32, No. 10, pp. 761-768. https://doi.org/10.3795/KSME-B.2008.32.10.761
  5. Ohm, I. and Park, C., 2009, "In-Cylinder Compression Flow Characteristics of Helical Port Engines with Wide Valve Angle," Trans. Korean Soc. Mech. Eng. B, Vol. 32, No. 1, pp. 9-16.
  6. Park, C. and Ohm, I., 2015, "Study on Evaluation Method of Flow Characteristics in Steady Flow Bench(1)-Raising Issue," Transactions of KSAE, Vol. 23, No. 1, pp. 88-96. https://doi.org/10.7467/KSAE.2015.23.1.088
  7. Park, C. and Ohm, I., 2015, "Study on Evaluation Method of Flow Characteristics in Steady Flow Bench(2)-Comparison of ISM and PIV Measurement," Transactions of KSAE, Vol. 23, No. 1, pp. 139-147. https://doi.org/10.7467/KSAE.2015.23.1.139
  8. Park, C., Sung, J. and Ohm, I., 2016, "Study on Evaluation Method of Flow Characteristics in Steady Flow Bench(3)-Velocity Profile(1)," Transactions of KSAE., Vol. 24, No. 2, pp. 169-182. https://doi.org/10.7467/KSAE.2016.24.2.169
  9. Park, C., Sung, J. and Ohm, I., 2016, "Study on Evaluation Method of Flow Characteristics in Steady Flow Bench(4)-Velocity Profile(2)," Transactions of KSAE., Vol. 24, No. 2, pp. 242-254. https://doi.org/10.7467/KSAE.2016.24.2.242
  10. Kim, H. and Ohm, I., 2016, "Effects of Port Shape on Steady Flow Characteristics in an SI Engine with Semi-Wedge Combustion Chamber (1)-Velocity Distribution(1)," Trans. Korean Soc. Mech. Eng. B, Vol. 40, No. 7, pp. 417-427. https://doi.org/10.3795/KSME-B.2016.40.7.417
  11. Heywood, J. B., 1988, Internal Combustion Engine Fundamentals. Int. edn., McGraw-Hill, pp. 345-349, Singapore.
  12. SwRI, "Cylinder Head Port Design," Presentation, 1999.