Steel and Composite Structures

Techno-Press (테크노프레스)
권호 표지
DOI QR코드

DOI QR Code

Bond between FRP formworks and concrete-effect of surface treatments and adhesives

  • Received : 2015.09.12
  • Accepted : 2015.12.01
  • Published : 2016.02.29
⟨ Previous Next ⟩

Abstract

FRP stay-in-place (SIP) formworks are designed as a support for casting concrete and as a tension reinforcement when concrete is cured. Bond development between SIP formwork and concrete is critical for FRP tension element to be effective. This paper reports the bond strength between FRP formwork and concrete for different interfacial treatments. A novel experimental setup is prepared for observing the bond behaviour. Three different adhesives with varying workability have been investigated. Along with the load-deformation characteristics, bond slip and strains in the formwork have been measured. A finite element numerical simulation was conducted for the experiments to understand the underlying mechanism. The results show that the adhesive bonding has the best bond strength.

Keywords

References

  1. Bakis, C., Bank, L., Brown, V., Cosenza, E., Davalos, J., Lesko, J., Machida, A., Rizkalla, S. and Triantafillou, T. (2002), "Fiber-reinforced polymer composites for construction - State-of-the-art review", J. Compos. Construct., 6(2), 73-87. https://doi.org/10.1061/(ASCE)1090-0268(2002)6:2(73)
  2. Bank, L., Oliva, M., Bae, H.-U., Barker, J. and Yoo, S.-W. (2007), "Pultruded FRP plank as formwork and reinforcement for concrete members", Adv. Struct. Eng., 10(5), 525-535. https://doi.org/10.1260/136943307782417681
  3. Berg, A.C., Bank, L.C., Oliva, M.G. and Russell, J.S. (2006), "Construction and cost analysis of an FRP reinforced concrete bridge deck", Construct. Build. Mater., 20(8), 515-526. https://doi.org/10.1016/j.conbuildmat.2005.02.007
  4. Boles, R., Nelson, M. and Fam, A. (2014), "Durability of bridge deck with FRP stay-in-place structural forms under freeze-thaw cycles", J. Compos. Construct., 19(4), 04014070. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000531
  5. Brosens, K. and Van Gemert, D. (1997), "Anchoring stresses between concrete and carbon fibre reinforced laminates", Proceedings of International Conference on Composite Construction-Conventional and Innovative, Innsbruck, Austria, September.
  6. Chajes, M.J., Finch, W.W., Januszka, T.F. and Thomson, T.A. (1996), "Bond and force transfer of composite-material plates bonded to concrete", Struct. J., 93(2), 209-217.
  7. Cheng, L., Zhao, L., Karbhari, V., Hegemier, G. and Seible, F. (2005), "Assessment of a steel-free fiber reinforced polymer-composite modular bridge system", J. Struct. Eng., 131(3), 498-506. https://doi.org/10.1061/(ASCE)0733-9445(2005)131:3(498)
  8. Cho, K., Cho, J.-R., Chin, W.-J. and Kim, B.-S. (2006), "Bond-slip model for coarse sand coated interface between FRP and concrete from optimization technique", Comput. Struct., 84(7), 439-449. https://doi.org/10.1016/j.compstruc.2005.10.004
  9. Cho, J.-R., Cho, K., Park, S.Y., Kim, S.T. and Kim, B.-S. (2010), "Bond characteristics of coarse sand coated interface between stay-in-place fibre-reinforced polymer formwork and concrete based on shear and tension tests", Can. J. Civil Eng., 37(5), 706-718. https://doi.org/10.1139/L10-012
  10. Dieter, D.A. (2002), Experimental and Analytical Study of Concrete Bridge Decks Constructed with FRP Stay-in-Place Forms and FRP Grid Reinforcing, University of Wisconsin-Madison, Madison, WI, USA.
  11. Dieter, D., Dietsche, J., Bank, L., Oliva, M. and Russell, J. (2002), "Concrete bridge decks constructed with fiber-reinforced polymer stay-in-place forms and grid reinforcing", Transportation Research Record: J. Transport. Res. Board, 1814(26), 219-226. https://doi.org/10.3141/1814-26
  12. Fam, A. and Nelson, M. (2012), "New bridge deck cast onto corrugated GFRP stay-in-place structural forms with interlocking connections", J. Compos. Construct., 16(1), 110-117. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000229
  13. Fam, A. and Rizkalla, S. (2001), "Behavior of axially loaded concrete-filled circular fiber-reinforced polymer tubes", Struct. J., 98(3), 280-289.
  14. Hall, J. and Mottram, J. (1998), "Combined FRP reinforcement and permanent formwork for concrete members", J. Compos. Construct., 2(2), 78-86. https://doi.org/10.1061/(ASCE)1090-0268(1998)2:2(78)
  15. He, J., Liu, Y., Chen, A. and Dai, L. (2012), "Experimental investigation of movable hybrid GFRP and concrete bridge deck", Construct. Build. Mater., 26(1), 49-64. https://doi.org/10.1016/j.conbuildmat.2011.05.002
  16. Honickman, H.N. (2008), Pultruded GFRP Sections as Stay-in-Place Structural Open Formwork for Concrete Slabs and Girders, Queen's University Kingston, ON, Canada.
  17. Honickman, H. and Fam, A. (2009), "Investigating a structural form system for concrete girders using commercially available GFRP sheet-pile sections", J. Compos. Construct., 13(5), 455-465. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000039
  18. Hosseini, A. and Mostofinejad, D. (2014), "Effective bond length of FRP-to-concrete adhesively-bonded joints: Experimental evaluation of existing models", Int. J. Adhes. Adhes., 48, 150-158. https://doi.org/10.1016/j.ijadhadh.2013.09.022
  19. Keller, T., Schaumann, E. and Vallee, T. (2007), "Flexural behavior of a hybrid FRP and lightweight concrete sandwich bridge deck", Composites Part A: Appl. Sci. Manuf., 38(3), 879-889. https://doi.org/10.1016/j.compositesa.2006.07.007
  20. Li, L., Shao, Y. and Wu, Z. (2010), "Durability of wet bond of hybrid laminates to cast-in-place concrete", J. Compos. Construct., 14(2), 209-216. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000060
  21. Matta, F., Nanni, A., Ringelstetter, T.E. and Bank, L.C. (2006), Rapid Construction of Concrete Bridge Deck using Prefabricated FRP Reinforcement.
  22. Mukherjee, A. and Arwikar, S.J. (2005a), "Performance of glass fiber reinforced polymer rebars in tropical environment- II.Microstructural tests", ACI Struct. J., 102(6), 816-822.
  23. Mukherjee, A. and Arwikar, S.J. (2005b), "Performance of gass fiber-reinforced polymer reinforcing bars in tropical environments - Part I: Structural scale tests", ACI Struct. J., 102(5), 745-753.
  24. Mukherjee, A. and Arwikar, S.J. (2007a), "Performance of externally bonded GFRP sheets on concrete in tropical environments.Part I: Structural scale tests", Compos. Struct., 81(1), 21-32. https://doi.org/10.1016/j.compstruct.2006.05.013
  25. Mukherjee, A. and Arwikar, S.J. (2007b), "Performance of externally bonded GFRP sheets on concrete in tropical environments.Part II: Microstructural tests", Compos. Struct., 81(1), 33-40. https://doi.org/10.1016/j.compstruct.2006.05.002
  26. Mukherjee, A. and Jain, K. (2013), "A semi-analytical model of cyclic behavior of reinforced concrete joints rehabilitated with FRP", Adv. Struct. Eng., 16(12), 2019-2034. https://doi.org/10.1260/1369-4332.16.12.2019
  27. Mukherjee, A. and Joshi, M. (2005), "FRPC reinforced concrete beam-column joints under cyclic excitation", Compos. Struct., 70(2), 185-199. https://doi.org/10.1016/j.compstruct.2004.08.022
  28. Mukherjee, A., Boothby, T., Bakis, C., Joshi, M. and Maitra, S. (2004), "Mechanical behavior of fiberreinforced polymer-wrapped concrete columns - Complicating effects", J. Compos. Construct., 8(2), 97-103. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:2(97)
  29. Mukherjee, A., Bagadi, S.P. and Rai, G.L. (2009), "Semianalytical modeling of concrete beams rehabilitated with externally prestressed composites", J. Compos. Construct., 13(2), 74-81. https://doi.org/10.1061/(ASCE)1090-0268(2009)13:2(74)
  30. Nelson, M., Eldridge, A. and Fam, A. (2013), "The effects of splices and bond on performance of bridge deck with FRP stay-in-place forms at various boundary conditions", Eng. Struct., 56, 509-516. https://doi.org/10.1016/j.engstruct.2013.05.031
  31. Nelson, M.S., Fam, A.Z., Busel, J.P., Bakis, C.E., Nanni, A., Bank, L.C., Henderson, M. and Hanus, J. (2014), "FRP stay-in-place structural forms for concrete bridge decks: A state-of-the-art review", Struct. J., 111(5).
  32. Reising, R., Shahrooz, B., Hunt, V., Neumann, A. and Helmicki, A. (2004), "Performance comparison of four fiber-reinforced polymer deck panels", J. Compos. Construct., 8(3), 265-274. https://doi.org/10.1061/(ASCE)1090-0268(2004)8:3(265)
  33. Ringelstetter, T., Bank, L., Oliva, M., Russell, J., Matta, F. and Nanni, A. (2006), "Cost-effective, structural stay-in-place formwork system of fiber - Reinforced polymer for accelerated and durable bridge deck construction", Transportation Research Record: J. Transport. Res. Board, 1976, 183-189.
  34. Shield, C., French, C. and Milde, E. (2005), "The effect of adhesive type on the bond of NSM tape to concrete", Special Publication, 230, 355-372.
  35. Teng, J. and Lam, L. (2004), "Behavior and modeling of fiber reinforced polymer-confined concrete", J. Struct. Eng., 130(11), 1713-1723. https://doi.org/10.1061/(ASCE)0733-9445(2004)130:11(1713)
  36. Ueda, T. and Dai, J. (2005), "Interface bond between FRP sheets and concrete substrates: properties, numerical modeling and roles in member behaviour", Prog. Struct. Eng. Mater., 7(1), 27-43. https://doi.org/10.1002/pse.187
  37. Wang, H. and Belarbi, A. (2005), "Flexural behavior of fiber-reinforced-concrete beams reinforced with FRP rebars", Special Publication, 230, 895-914.
  38. Wright, H.D., Evans, H.R. and Harding, P.W. (1987), "The use of profiled steel sheeting in floor construction", J. Constr. Steel Res., 7(4), 279-295. https://doi.org/10.1016/0143-974X(87)90003-4
  39. Wu, Z. and Yin, J. (2003), "Fracturing behaviors of FRP-strengthened concrete structures", Eng. Fract. Mech., 70(10), 1339-1355. https://doi.org/10.1016/S0013-7944(02)00100-5
  40. Wu, L., Hoa, S.V. and Ton-That, M.-T. (2004), "Effects of water on the curing and properties of epoxy adhesive used for bonding FRP composite sheet to concrete", J. Appl. Polym. Sci., 92(4), 2261-2268. https://doi.org/10.1002/app.20195
  41. Zhang, P., Wu, G., Zhu, H., Meng, S. and Wu, Z. (2014), "Mechanical performance of the wet-bond interface between FRP plates and cast-in-place concrete", J. Compos. Construct., 18(6), 04014016. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000472
  42. Zhang, L., Wang, W., Harries, K. and Tian, J. (2015), "Bonding behavior of wet-bonded GFRP-concrete interface", J. Compos. Construct., 19(6), 04015001. https://doi.org/10.1061/(ASCE)CC.1943-5614.0000550

Cited by

  1. The GFRP profiles as stay-in-place formwork vol.49, pp.2267-1242, 2018, https://doi.org/10.1051/e3sconf/20184900008