DOI QR코드

DOI QR Code

가동원전에서 공정모델링을 통한 PID 튜닝 시뮬레이션 방법

A Simulation Method of PID Tuning with Process Modeling in Operating Nuclear Power Plants

  • Min, Moon-Gi (I&C Engineering Center, Korea Hydro & Nuclear Power Co., Ltd.) ;
  • Jung, Chang-Gyu (I&C Engineering Center, Korea Hydro & Nuclear Power Co., Ltd.) ;
  • Lee, Kwang-Hyun (I&C Engineering Center, Korea Hydro & Nuclear Power Co., Ltd.) ;
  • Lee, Jae-Ki (I&C Engineering Center, Korea Hydro & Nuclear Power Co., Ltd.) ;
  • Kim, Hee-Je (Dept. of Electrical and Electronic Engineering, Pusan National University)
  • 투고 : 2014.11.11
  • 심사 : 2014.11.27
  • 발행 : 2014.12.01

초록

PID(Proportional, Integral, Derivative) controller is the most popular process controllers in nuclear power plants. The optimized parameter setting of the process controller contributes to the stable operation and the efficiency of the operating nuclear power plants. PID parameter setting is tuned when new process control systems are installed or current process control systems are changed. When the nuclear plant is shut down, a lot of PID tuning methods such as the Trial and Error method, Ultimate Oscillation method operation, Ziegler-Nichols method, frequency method are used to tune the PID values. But inadequate PID parameter setting can be the cause of the unstable process of the operating nuclear power plant. Therefore the results of PID parameter setting should be simulated, optimized and finally verified. This paper introduces the simulation method of PID tuning to optimize the PID parameter setting and confirms them of the actual PID controller in the operating nuclear power plants. The simulation method provides the accurate process modeling and optimized PID parameter setting of the multi-loop control process in particular.

키워드

참고문헌

  1. VDI-Handbuch, "Steam Temperature Control in Fossil Fired Steam Power Stations", VDI/VDE 3505, pp. 4-9 September 1996.
  2. Ziegler, J. G. and N. B. Nicholes, "Optimum settings for Automatic Controllers", Trans. ASME, 64, pp. 759-768, 1942.
  3. Jae-He Choi, "Trial and Error PID Controller Tuning", Automatic Control, Vol.17, pp. 114-119, November 2004.
  4. Yamamoto, Yugushida, "PID Tuning based on plant operating data", Automatic Control, Vol.292, pp. 72-76, March 2009.
  5. Chan-Ho Sung, Moon-Gi Min, "A Method of Tuning Optimization for PID Controller in Nuclear Power Plants", KPVP Vol.10, No. 1, June 2014.
  6. Young-Cheol Park, "Understanding Tuning & Control", Korea Instrument & Control Training Institute(KITI), pp. 60-71, March 2008.
  7. In-Gyu Choi, Gwang-Myeong Yu, "Analysis Report of Calculation Algorithm for PID Controller Tuning Parameters", KEPRI, pp. 4-25, January 2013.
  8. PAS, "PID Controller Tuning, Process Diagnostics, Control Loop Simulation", Tune Wizard, pp. 93-116, June 2005.
  9. Lennart Liung, "Matlab System Identification Toolbox User's Guide", Mathworks, pp. 318-401, April 2011.
  10. Matlab simulink, "Matlab Simulink User's Guide", Mathwork, pp. 68-161, April 2011.
  11. M.A. Eggenberger, "Fundamental Explanation of Transfer Function for Control Systems", GE Power Systems Steam Turbine GEK 103794, pp. 61-66, June 1996.