DOI QR코드

DOI QR Code

Local Buckling Strength of PFRP I-Shape Compression Members Obtained by LRFD Design Method and Closed-Form Solution

하중저항계수설계법 및 정밀해법에 의한 PFRP I형 단면 압축재의 국부좌굴강도

  • Received : 2014.05.29
  • Accepted : 2014.06.24
  • Published : 2014.06.30

Abstract

Fiber reinforced polymeric plastic (FRP) materials have many advantages over conventional structural materials, i.e., high specific strength and stiffness, high corrosion resistance, right weight, etc. Among the various manufacturing methods, pultrusion process is one of the best choices for the mass production of structural plastic members. Since the major reinforcing fibers are placed along the axial direction of the member, this material is usually considered as an orthotropic material. However, pultruded FRP (PFRP) structural members have low modulus of elasticity and are composed of orthotropic thin plate components the members are prone to buckle. Therefore, stability is an important issue in the design of the pultruded FRP structural members. Many researchers have conducted related studies to publish the design method of FRP structures and recently, referred to the previous researches, pre-standard for LRFD of pultruded FRP structures is presented. In this paper, the accuracy and suitability of design equation for the local buckling strength of pultruded FRP I-shape compression members presented by ASCE are estimated. In the estimation, we compared the results obtained by design equation, closed-form solution, and experiments conducted by previous researches.

Keywords

References

  1. American Society of Civil Engineers (2010), Pre-Standard for Load & Resistance Factor Design of Pultruded Fiber Reinforced Polymer Structures, American Composites Manufacturers Association.
  2. Chae, S. H. (2005), A Study on the Analysis and Design of Orthotopic Thin-Walled Columns, PhD Thesis, Hongik University, Seoul. (in Korean).
  3. Choi, J. W. (2009), Local Buckling Load of Pultruded Structural Members with Material Properties Variations in the Cross-Section, MS Thesis, Hongik University, Seoul. (in Korean).
  4. Choi, J. W., Lee, K. Y., Park, J. H., and Yoon, S. J. (2012), "An Analytical Study on the Buckling of Orthotropic Plates and Local Buckling of Compression Members," Journal of the Korean Society for Advanced Composite Structures, Vol. 3, No. 1, pp. 21-28. (in Korean). https://doi.org/10.11004/kosacs.2012.3.1.021
  5. Choi, J. W., Lee, S., Joo, H. J., Kim, C. W., Ok, D. M., and Yoon, S. J. (2011), "Design Consideration of the Nonuniform Stress Distribution of Pultruded Structural Member under Compression," Advanced Materials Research, Vols. 250-253, pp. 3564-3570. https://doi.org/10.4028/www.scientific.net/AMR.250-253.3564
  6. Joo, H. J. (2003), A Study on the Local Buckling Analysis of Orthotropic I-Shape Compression Members, MS Thesis, Hongik University, Seoul. (in Korean).
  7. Joo, H. J. (2010), Buckling Behavior and Design of Pultruded Thin-Walled Open Section Compression Members, PhD Thesis, Seoul, Hongik University.
  8. Kollar, L. (2002), "Buckling of Unidirectionally Loaded Composite Plates with One Free and One Rotationally Restrained Unloaded Edge," Journal of Structural Engineering, ASCE, Vol. 128, No. 9, pp. 1202-1211. https://doi.org/10.1061/(ASCE)0733-9445(2002)128:9(1202)
  9. Kollar, L. (2003), "Local Buckling of Fiber-Reinforced Plastic Composite Structural Members with Open and Closed Cross Sections," Journal of Structural Engineering, ASCE, Vol. 129, No. 11, pp. 1503-1513. https://doi.org/10.1061/(ASCE)0733-9445(2003)129:11(1503)
  10. Lee, S. (2003), Flexural-Torsional Buckling of Pultruded T-Sections, PhD Thesis, Georgia Institute of Technology, Atlanta, GA.
  11. Yoon, S. J. (1993), Local Buckling of Pultruded I-Shape Columns, PhD Thesis, Georgia Institute of Technology, Atlanta, GA.
  12. Zureick, A. and Steffen, R. (2000), "Behavior and Design of Concentrically Loaded Pultruded Angle Struts," Journal of Structural Engineering, ASCE, Vol. 126, No. 3, pp. 406-416. https://doi.org/10.1061/(ASCE)0733-9445(2000)126:3(406)