International Journal of Precision Engineering and Manufacturing

Korean Society for Precision Engineering (한국정밀공학회)
권호 표지

A Comparative Study of Transistor and RC Pulse Generators for Micro-EDM of Tungsten Carbide

  • Jahan, Muhammad Pervej (Department of Mechanical Engineering, National University of Singapore) ;
  • Wong, Yoke San (Department of Mechanical Engineering, National University of Singapore) ;
  • Rahman, Mustafizur (Department of Mechanical Engineering, National University of Singapore)
  • Published : 2008.10.01
Download PDF
⟨ Previous Next ⟩

Abstract

Micro-electrical discharge machining (micro-EDM) is an effective method for machining all types of conductive materials regardless of hardness. Since micro-EDM is an electro-thermal process, the energy supplied by the pulse generator is an important factor in determining the effectiveness of the process. In this study, an investigation was conducted on the micro-EDM of tungsten carbide (WC) to compare the performance of transistor and resistance/capacitance (RC) pulse generators in obtaining the best quality micro-hole. The performance was measured by the machining time, material removal rate, relative tool wear ratio, surface quality, and dimensional accuracy. The RC generator was more suited for minimizing the pulse energy, which is a requirement for fabricating micro-parts. The smaller-sized debris formed by the low-discharge energy of RC micro-EDM could be easily flushed away from the machined zone, resulting in a surface free of burrs and resolidified molten metal. The RC generator also required much less time to obtain the same quality micro-hole in WC. Therefore, RC generators are better suited for fabricating micro-structures, producing good surface quality and better dimensional accuracy than the transistor generators, despite their higher relative tool wear ratio.

Keywords

References

  1. Masuzawa, T., "State of the art micromachining," Annals of CIRP, Vol. 49, No. 2, pp. 473-488, 2000 https://doi.org/10.1016/S0007-8506(07)63451-9
  2. Mahdavinejad, R. A. and Mahdavinejad, A., "ED machining of WC-Co," Journal of Materials Processing Technology, Vol. 162-163, pp. 637-643, 2005 https://doi.org/10.1016/j.jmatprotec.2005.02.211
  3. Pandey, P. C. and Jilani, S. T., "Electrical Machining characteristics of cemented carbides," Wear, Vol. 116, No. 1, pp. 77-88, 1987 https://doi.org/10.1016/0043-1648(87)90269-9
  4. Puertas, I., Luis, C. J. and Alvarez, L., 'Analysis of the influence of EDM parameters on surface quality, MRR and EW of WC-Co,' Journal of Materials processing technology, Vol. 153-154, pp. 1026-1032, 2004 https://doi.org/10.1016/j.jmatprotec.2004.04.346
  5. Yan, B. H., Huang, F. Y., Chow, H. M. and Tsai, J. Y., 'Micro-hole machining of carbide by electrical discharge machining,' Journals of Materials Processing Technology, Vol. 87, Issues 1-3, pp. 139-145, 1999 https://doi.org/10.1016/S0924-0136(98)00345-8
  6. Jung, J. W., Ko, S. H., Jeong, Y. H., Min, B. K. and Lee, S. J., 'Estimation of material removal volume of a micro-EDM drilled hole using discharge pulse monitoring,' International Journal of Precision Engineering and Manufacturing, Vol. 8, No. 4, pp. 45-49, 2007
  7. Kim, Y. T., Park, S. J. and Lee, S. J., 'Micro/Meso-scale shapes machining by micro EDM process,' International Journal of Precision Engineering and Manufacturing, Vol. 6, No. 2, pp. 5-11, 2005
  8. Han, F., Wachi, S. and Kunieda, M., 'Improvement of machining characteristics of micro-EDM using transistor type isopulse generator and servo feed control,' Precision Engineering, Vol. 28, No. 4, pp. 378-385, 2004 https://doi.org/10.1016/j.precisioneng.2003.11.005
  9. McGeough, J. A., 'Advanced Methods of Machining,' Chapman and Hall, pp. 129-133, 1988
  10. Kunieda, M., Lauwers, B., Rajurkar, K. P. and Schumacher, B. M., 'Advancing EDM through fundamental insight into the process,' Annals of CIRP, Vol. 54, No. 2, pp. 599-622, 2005
  11. Lim, H. S., Wong, Y. S., Rahman, M. and Lee, E. M. K., 'A study on the machining of high-aspect ratio micro-structures using micro EDM,' Journals of Materials Processing Technology, Vol. 140, Issues 1-3, pp. 318-325, 2003 https://doi.org/10.1016/S0924-0136(03)00760-X
  12. Lee, S. H. and Li, X. P., 'Study of the effect of machining parameters on the machining characteristics in EDM of WC,' Journal of Materials Processing Technology, Vol. 115, No. 3, pp. 344-355, 2001 https://doi.org/10.1016/S0924-0136(01)00992-X
  13. Egashira, K., Matsugasako, A., Tsuchiya, H. and Miyazaki, M., 'Electrical discharge machining with ultralow discharge energy,' Precision Engineering, Vol. 30, No. 4, pp. 414-420, 2006 https://doi.org/10.1016/j.precisioneng.2006.01.004
  14. Liu, H. S., Yan, B. H., Huang, F. Y. and Qiu, K. H., 'A study on the characterization of high nickel alloy micro-holes using micro-EDM and their applications,' Journal of Materials Processing Technology, Vol. 169, No. 3, pp. 418-426, 2005 https://doi.org/10.1016/j.jmatprotec.2005.04.084
  15. Wong, Y. S., Rahman, M., Lim, H. S., Han, H. and Ravi, N., 'Investigation of micro-EDM material removal characteristics using single RC-pulse discharges,' Journal of Materials Processing Technology, Vol. 140, Issues 1-3, pp. 303-307, 2003 https://doi.org/10.1016/S0924-0136(03)00771-4
  16. Liao, Y. S., Huang, J. T. and Chen, Y. H., 'A study to achieve a fine surface finish in Wire-EDM,' Journal of Materials Processing Technology, Vol. 149, Issues 1-3, pp. 165-171, 2004 https://doi.org/10.1016/j.jmatprotec.2003.10.034