한국분말재료학회지 (Journal of Powder Materials)

  • 제15권3호
  • /
  • Pages.196-203
  • /
  • 2008
  • /
  • 2799-8525(pISSN)
  • /
  • 2799-8681(eISSN)
한국분말재료학회 (*구 분말야금학회) (The Korean Powder Metallurgy & Materials Institute)
권호 표지
DOI QR코드

DOI QR Code

Al-20Si-5.5Fe-1.2Mg-0.5Mn 합금분말의 치밀화에 미치는 소결온도와 분위기의 영향

Effects of Sintering Temperature and Atmosphere on Densification of Hypereutectic Al-Si Alloy Powders

  • 이재욱 (한국기계연구원 부설 재료연구소 분말재료연구부) ;
  • 박상빈 (한국기계연구원 부설 재료연구소 분말재료연구부) ;
  • 양상선 (한국기계연구원 부설 재료연구소 분말재료연구부) ;
  • 김용진 (한국기계연구원 부설 재료연구소 분말재료연구부)
  • Lee, Jae-Wook (Department of Powder Materials Research, Korea Institute of Materials Science) ;
  • Park, Sang-Bin (Department of Powder Materials Research, Korea Institute of Materials Science) ;
  • Yang, Sang-Sun (Department of Powder Materials Research, Korea Institute of Materials Science) ;
  • Kim, Yong-Jin (Department of Powder Materials Research, Korea Institute of Materials Science)
  • 발행 : 2008.06.28
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

The densification behavior of Al-20Si-5.5Fe-1.2Mg-0.5Mn powders was investigated through micro-structure analysis of sintered specimens. The specimens sintered in vacuum or in high purity (99.999%) nitrogen showed porous near-surface microstructures. The densification of near-surface part was enhanced by means of ultra-high purity (99.9999%) nitrogen atmosphere. The relationship between slow densification and oxide surfaces of Al alloy powders was discussed. And the effects of Mg addition, nitrogen gas, and humidity on densification were discussed. In addition, the rapid growth of primary Si crystals above the critical temperature was reported.

키워드

참고문헌

  1. R. B. Bhagat: ASM Handbook ASM International, 7 (1998) 840
  2. J. U. Ejiofor and R. G. Reddy: JOM, 49 (1997) 31
  3. G. B. Schaffer, T. B. Sercombe and R. N. Lumley: Mater. Chem. Phys., 67 (2001) 85 https://doi.org/10.1016/S0254-0584(00)00424-7
  4. R. N. Lumley, T. B. Sercombe and G. B. Schaffer: Metall. Mater. Trans. A, 30 (1999) 457 https://doi.org/10.1007/s11661-999-0335-y
  5. T. B. Sercombe and G. B. Schaffer: Acta Mater., 52 (2004) 3019 https://doi.org/10.1016/j.actamat.2004.03.004
  6. Y. J. Kim and J. C. Kim: J. Korean Powder Metall. Inst., 12 (2005) 296 (Korean) https://doi.org/10.4150/KPMI.2005.12.4.296
  7. G. Timmermans, L. Froyen and J. van Humbeeck: J. Mater. Sci., 35 (2000) 3289 https://doi.org/10.1023/A:1004831623843
  8. E. Crossin, J.-Y. Yao and G. B. Schaffer: Powder Metall., 50 (2007) 354 https://doi.org/10.1179/174329007X223947
  9. G. B. Schaffer, J.-Y. Yao, S. J. Bonner, E. Crossin, S. J. Pas and A. J. Hill: Acta Mater., 56 (2008) 2615 https://doi.org/10.1016/j.actamat.2008.01.047
  10. T. B. Sercombe and G. B. Schaffer: Science, 301 (2003) 1225 https://doi.org/10.1126/science.1086989
  11. O. J. Kwon and D. N. Yoon: Sintering Processes, G. C. Kuczynski(ed.), Plenum Press, New York (1980) 203
  12. G. B. Schaffer and B. J. Hall: Metall. Mater. Trans. A, 33 (2002) 3279 https://doi.org/10.1007/s11661-002-0314-z
  13. T. B. Schaffer, B. J. Hall, S. J. Bonner, S. H. Huo and T. B. Sercombe: Acta Mater., 54 (2006) 131
  14. R. E. Napolitano, H. Meco and C. Jung: JOM, 56 (2004) 16

피인용 문헌

  1. Effect Of Different Mechanical Milling Processes On Morphology And Microstructural Changes Of Nano And Micron Al-Powders vol.60, pp.2, 2015, https://doi.org/10.1515/amm-2015-0105