Pickup 렌즈의 사출조건이 복굴절 및 굴절율에 미치는 영향에 관한 연구

A Study on Influence of Parameters and Characteristics in the Injection Process on the Birefringence and Refractive Index for Pickup Lens

  • 이승준 (한국산업기술대학교 지식기반기술 에너지대학원 나노광공학과) ;
  • 현동훈 (한국산업기술대학교 나노광공학과)
  • 발행 : 2007.12.15

초록

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for birefringence and refractive index for pickup lens. This paper presents the birefringence and refractive index reduced with increasing the holding pressure and also the holding pressure time. And there are interaction with birefringence and fill time in the injection process. The optimal conditions through DOE are validated by using injection molding analysis.

키워드

참고문헌

  1. Ha, Y. W., Jung, T. H. and Lee, B. J., 2002, 'Injection Moulding of Polyetherimide Axi-Symmetric Elements,' Transactions of the Korean Society of Machine Tool Engineers, Vol. 11, No. 6, pp. 68-74
  2. Kang, S. D., Kim, W. S., Jang, K. H. and Kim, D. H., 2004, 'A Study on the Compensation of Ultra-precision Aspheric Lens Mold,' Proceeding of KSPE spring conference, pp. 237-238
  3. Kim, J. S. and Yoon, K. H., 2003, 'A Study on the Prediction of Thermally-Induced Residual Stress and Birefringence in Quenched Polystyrene Plate Including Free Volume Theory,' KSME (A), Vol. 27, No. 1, pp. 77-87
  4. Yoon, K. H., 1996, 'On The Manufacturing Process of a Optical Disk Substrate,' Polymer Science and Technology, Vol. 7, No. 3, pp. 284-290
  5. Otani, Y., Shimada, T., Yoshizawa, T. and Umeda, N., 1994, 'Two-dimensional birefringence measurement using the phase shifting technique,' Opt. Engng., Vol. 33, pp. 1604-1609 https://doi.org/10.1117/12.168435
  6. Shyu, G. D., 1993, Birefringence and Residual Stresses in Molded Articles of Amorphous Polymers, Ph. D. Thesis, The University of Akron
  7. Lee, Y. B., Kwon, T. H. and Yoon, K. H., 2002, 'Numerical Analysis of Residual Stresses and Birefringence in Injection/Compression molded Center-Gated Disk. Part I and Part II,' KSME (A), Vol. 26, No. 11, pp.2342-2354 & 2355-2363 https://doi.org/10.3795/KSME-A.2002.26.11.2342
  8. Kim, H. P. and Kim, Y. J., 2002, 'A Study on the Effects of Filling and Packing Phases on the Injection Molding,' Proceeding of the KSMTE spring conference, pp. 112-118
  9. Lee, H. S., Lee, H. K. and Yang, G. E., 2005, 'A Study on Injection Molding Analysis and Validation of Large Injection-Molded Body Using Design of Experiment', Proceeding of the KSMTE spring conference, pp. 109-114
  10. Lee, S. B., 2005, Design of Experiment by Minitab, ELECTRIC INC