Advanced Composite Materials

The Korean Society for Composite Materials (한국복합재료학회)
권호 표지

Modeling of the filling process during resin injection/compression molding

  • Chang, Chih-Yuan (Department of Mechanical and Automation Engineering, Kao Yuan University)
  • Published : 2007.09.01
Download PDF
⟨ Previous Next ⟩

Abstract

The filling process of resin injection/compression molding (I/CM) can be divided into injection and compression phases. During the resin injection the mold is kept only partially closed and thus a gap is present between the reinforcements and the upper mold. The gap results in preferential flow path. After the gap is filled with the resin, the compression action initiates and forces the resin to penetrate into the fiber preform. In the present study, the resin flow in the gap is simplified by using the Stokes approximation, while Darcy's law is used to calculate the flow field in the fiber mats. Results show that most of the injected resins enter into the gap during the injection phase. The resin injection time is extremely short so the duration of the filling process is determined by the final closing action of the mold cavity. Compared with resin transfer molding (RTM), I/CM process can reduce the mold filling time or injection pressure significantly.

Keywords

References

  1. C. Brockmann and W. Michaeli, Injection compression molding - a low pressure process for manufacturing textile-covered mouldings, ANTEC'97 1, 441-445 (1997)
  2. K. Han, J. Ni, J. Toth, L. J. Lee and J. P. Greene, Analysis of an injection/compression liquid composite molding process, Polym. Compos. 19, 487-496 (1998) https://doi.org/10.1002/pc.10123
  3. S. Wirth and R. Gauvin, Experimental analysis of mold filling in compression resin transfer molding, J. Reinf. Plast. Compos. 17, 1414-1430 (1998) https://doi.org/10.1177/073168449801701602
  4. C. Y. Chang, L. W. Hourng and C. S. Yu, Analysis of flow phenomena during the filling stage of CTM, J. Reinf. Plast. Compos. 23, 1561-1570 (2004) https://doi.org/10.1177/0731684404039800
  5. C. Y. Chang, Simulation of mold filling in simultaneous resin injection/compression molding, J. Reinf. Plast. Compos. 25, 1255-1268 (2006) https://doi.org/10.1177/0731684406060253
  6. X. T. Pham and F. Trochu, Simulation of compression resin transfer molding to manufacture thin composite shell, Polym. Compos. 20, 436-459 (1999) https://doi.org/10.1002/pc.10369
  7. M. K. Kang and W. I. Lee, Analysis of resin transfer/compression molding process, Polym. Compos. 20, 293-304 (1999) https://doi.org/10.1002/pc.10356
  8. S. Bickerton and M. Z. Abdullah, Modeling and evaluation of the filling stage of injection/ compression moulding, Compos. Sci. Technol. 63, 1359-1375 (2003) https://doi.org/10.1016/S0266-3538(03)00022-8
  9. A. Shojaei, A numerical study of filling process through multilayer preforms in resin injection/ compression molding, Compos. Sci. Technol. 66, 1546-1557 (2006) https://doi.org/10.1016/j.compscitech.2005.11.035
  10. R. L. Riche, A. Saouab and J. Br'eard, Coupled compression RTM and composite layup optimization, Compos. Sci. Technol. 63, 2277-2287 (2003) https://doi.org/10.1016/S0266-3538(03)00195-7
  11. C. Y. Chang, L. W. Hourng and T. Y. Chou, Effect of process variables on the quality of compression resin transfer molding, J. Reinf. Plast. Comp. 25, 1027-1037 (2006) https://doi.org/10.1177/0731684406064997
  12. D. S. Burnett, Finite Element Analysis. Addison-Wesley Publishing Company, Singapore (1988)
  13. P. D. Thomas and J. F. Middlecoff, Direct control of the grid point distribution in meshes generated by elliptic equation, AIAA J. 18, 652-656 (1980) https://doi.org/10.2514/3.50801
  14. C. J. Wu, Numerical simulation on the edge effect of resin transfer molding, PhD Diss., Mech. Eng. Dept., National Central University, Taiwan (1995)
  15. C. Y. Chang and L. W. Hourng, Numerical simulation for the transverse impregnation in resin transfer molding, J. Reinf. Plast. Comp. 17, 165-182 (1998) https://doi.org/10.1177/073168449801700206