한국안전학회지 (Journal of the Korean Society of Safety)

  • 제21권4호
  • /
  • Pages.19-24
  • /
  • 2006
  • /
  • 1738-3803(pISSN)
  • /
  • 2383-9953(eISSN)
한국안전학회 (The Korean Society of Safety)
권호 표지

대형승용차 디스크 브레이크용 회주철의 피로균열 전파 거동

Fatigue Crack Growth Behavior of Gray Cast Iron for Brake Disc of a Passenger Car

  • 김호경 (서울산업대학교 자동차공학과) ;
  • 박진호 (서울산업대학교 산업대학원 자동차공학과) ;
  • 양경탁 (서울산업대학교 산업대학원 자동차공학과) ;
  • 최덕호 (서울산업대학교 산업대학원 자동차공학과)
  • Kim, Ho-Kyung (Department of Automotive Engineering, Seoul National University of Technology) ;
  • Park, Jin-Ho (Department of Automotive Engineering, Graduate School, Seoul National University of Technology) ;
  • Yang, Kyoung-Tak (Department of Automotive Engineering, Graduate School, Seoul National University of Technology) ;
  • Choi, Deok-Ho (Department of Automotive Engineering, Graduate School, Seoul National University of Technology)
  • 발행 : 2006.08.31
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Fatigue crack propagation tests for the brake disc cast iron were conducted for investigating fatigue crack propagation rate(da/dN), crack propagation path and fracture toughness($K_c$) of the material. The threshold stress intensity factor range, ${\Delta}K_{th}$, was found to be about $6MPa{\sqrt{m}}$ at the stress ratio of R = 0.1. Also, fracture toughness value was determined to be $24.7MPa{\sqrt{m}}$. Irregular fatigue fracture surfaces were observed, indicating that fatigue crack growth occurred at the interface between randomly scattered flak graphite and ferrite, where the interfacial strength was relatively weak.

키워드

참고문헌

  1. C. K. Kim, 'The effect of thermoelastic and wear on the leakage of compressible gases in shaft seals,' KSME J., Vol. 2, No.2, pp. 33 -139, 1988
  2. T. Lui, S. K. Rhee, 'High temperature wear of semimetallic disk brake pads', Proc. of the Conf. on Wear of Mat., pp. 552-554, 1977
  3. K. Seong, et al., 'The role of friction film in friction, wear, and noise of automotive brakes', SAE 90004, pp. 29-38, 1990
  4. T. J. Mackin et al., 'Thermal cracking in disc brakes', Eng. Failure Analysis, Vol. 9, pp. 63 -76, 2002 https://doi.org/10.1016/S1350-6307(00)00037-6
  5. 조종두, '자동 브레이크의 설계요소', 대한기계 학회지, 제39권, 제7호, pp. 49-57, 1997
  6. M. G. Jacko, S. K. Rhee, 'Encyclopedia of Composite Materials and Components, Wiley, pp. 144-154, 1983
  7. B. J. Briscoe, I. Ramirez I. P. J. Tweedle, Friction of aramid fiber composites, proc. Int. Conf. On Disc Brakes for Commercial Vehicles, London, I. Mech. Eng., London, Vol. pp. 15 -29, 1988
  8. M. J. Haigh, H. Smales, M. Abe, 'Vehicle judder under dynamic braking caused by disk thickness variation,' Proc. Inst. Mech. Eng. Conf., VoI.C444/022, pp. 247 -258, 1993
  9. Y. Jimbo. T. Mibe. K. Akiyama. H. Matsui. M. Yoshida. A. Ozowa. SAE- Tech. Paper. 900002. 1990
  10. Metal Handbook, 10th Edition, Vol. 1, pp. 12-32, ASM, 1990
  11. ASTM E399-83 'Standard test method for planestrain fracture toughness of metallic materials'
  12. ASTM E647-93 'Standard test method for measurement of fatigue crack growth rates'
  13. J. H. Bulloch, 'Near threshold fatigue behaviour of flake graphite cast irons microstructures', Theor. Appl. Fract. Mech. Vol. 24, pp. 65-78. 1995 https://doi.org/10.1016/0167-8442(95)00032-A