Computers and Concrete

  • 제2권1호
  • /
  • Pages.79-96
  • /
  • 2005
  • /
  • 1598-8198(pISSN)
  • /
  • 1598-818X(eISSN)
테크노프레스 (Techno-Press)
권호 표지
DOI QR코드

DOI QR Code

Predicting shear capacity of NSC and HSC slender beams without stirrups using artificial intelligence

  • El-Chabib, H. (Department of Civil and Environmental Engineering, The University of Western Ontario) ;
  • Nehdi, M. (Department of Civil and Environmental Engineering, The University of Western Ontario) ;
  • Said, A. (Department of Civil and Environmental Engineering, The University of Western Ontario)
  • 투고 : 2004.06.07
  • 심사 : 2004.10.19
  • 발행 : 2005.02.25
⟨ 이전 논문 다음 논문 ⟩

초록

The use of high-strength concrete (HSC) has significantly increased over the last decade, especially in offshore structures, long-span bridges, and tall buildings. The behavior of such concrete is noticeably different from that of normal-strength concrete (NSC) due to its different microstructure and mode of failure. In particular, the shear capacity of structural members made of HSC is a concern and must be carefully evaluated. The shear fracture surface in HSC members is usually trans-granular (propagates across coarse aggregates) and is therefore smoother than that in NSC members, which reduces the effect of shear transfer mechanisms through aggregate interlock across cracks, thus reducing the ultimate shear strength. Current code provisions for shear design are mainly based on experimental results obtained on NSC members having compressive strength of up to 50MPa. The validity of such methods to calculate the shear strength of HSC members is still questionable. In this study, a new approach based on artificial neural networks (ANNs) was used to predict the shear capacity of NSC and HSC beams without shear reinforcement. Shear capacities predicted by the ANN model were compared to those of five other methods commonly used in shear investigations: the ACI method, the CSA simplified method, Response 2000, Eurocode-2, and Zsutty's method. A sensitivity analysis was conducted to evaluate the ability of ANNs to capture the effect of main shear design parameters (concrete compressive strength, amount of longitudinal reinforcement, beam size, and shear span to depth ratio) on the shear capacity of reinforced NSC and HSC beams. It was found that the ANN model outperformed all other considered methods, providing more accurate results of shear capacity, and better capturing the effect of basic shear design parameters. Therefore, it offers an efficient alternative to evaluate the shear capacity of NSC and HSC members without stirrups.

키워드

참고문헌

  1. ACI Committee 318(1999), "Building code requirements for structural concrete", (ACI 318-99) American Concrete Institute, Farmington Hills, Michigan, USA, 369.
  2. Adebar, P., Collins, M. P.(1996), "Shear strength of members without transverse reinforcement", Canadian J. Civil Eng., 23, 30-41. https://doi.org/10.1139/l96-004
  3. Ahmad, S.H., Khaloo, A. R., and Poveda, A.(1986), "Shear capacity of reinforced high-strength concretebeams", ACI J., 83(2), 297-305.
  4. Ahmad, S.H., Park,F., and El-Dash, K.(1995), "Web reinforcement effects on shear capacity of reinf orced high-strength concrete beams", Magazine of Concrete Research, 47(172), 227-233. https://doi.org/10.1680/macr.1995.47.172.227
  5. Angelakos, D.(1999), "The influence of concrete strength and longitudinal reinforcement ratio on the shear strength of large-size reinforced concrete beams with and without transverse reinforcement", MSc. Thesis, Dept. of Civil Eng., University of Toronto, Canada, 181.
  6. Angelakos, D., Bentz, E. C., and Collins, M. P.(2001), "Effect of concrete strength and minimum stirrups on shear strength of large members", ACI Struct. J., 98(3), 290-300.
  7. Bazant, Z. P., and Kazemi, M. T.(1991), "Size effect on diagonal shear failure of beams without stirrups", ACI Struct. J., 88(3), 268-276.
  8. Bazant, Z. P., and Kim J-K.(1984), "Size effect in shear failure of longitudinally reinforced concrete beams", ACI J., Proc., 81(5), 456-468.
  9. Bentz,E., and Collins, M. P.(2000), "Response 2000, load-deformation response of reinforced concrete sections,version 1.0.5", http://www.ecf.utoronto.ca/-bentz/r2k.htm.
  10. Bohigas, A. C. (2002), "Shear design of reinforced high-strength concrete beams", Ph. D. Thesis, University Politecnica de Catalunya, Spain, 168.
  11. Chana, P. S.(1981), "Some aspects of modeling the behaviour of reinforced concrete under shear loading", Tech. Rep. No.543, Cement and Concrete Association, Wexham Springs, 21.
  12. Collins, M. P., and Kuchma, D.(1999), "How safe are our large, lightly reinforced concrete beams, slabs and footings?", ACI Struct. J., 96(4), 482-490.
  13. CSA Committee A23.3(1994), "Design of concrete structures", Canadian Standards Association, Rexdale, Ontario, Canada, 199.
  14. Duthinh, D., and Carino, N. J.(1996), "Shear design of high-strength concrete beams: a review of the state-of-the-art", Research Report NISTIR 5870, National Institute of Standards and Technology, Building and Fire Research Laboratory, Gaithersburg, MD, 198.
  15. Elzanaty, A. H., Nilson, A. H., and Slate, F. O.(1986), "Shear capacity of reinforced beams using high strength concrete", ACI J., 83(2), 290-296.
  16. Elzanaty, A. H., Nilson, A. H., and Slate, F. O.(1986), "Shear capacity of reinforced concrete beams using high-strength concrete", ACI J., 83(2), 290-296.
  17. European Committee for Standardization, Eurocode-2(2002), "Design of concrete structures, part 1: general rules and rules for buildings", Revised Final Draft, 226.
  18. Fujita,M., Sato, R., Matsumoto, K., and Takiki, Y.(2002), "Size effect on shear capacity of reinforced concrete beams using HSC without shear reinforcement", Proceeding 6th International Symposium on Utilisation of High Strength/High Performance Concrete, Edited by Koenig, Dehn, and Faust, Leipzig, Germany, 235-245.
  19. Ghannoum, W. M.(1998), "Size effect on shear strength of reinforced concrete beams", M. Eng. Thesis, Dept. Civil Eng. and Applied Mechanics, McGill University, Canada, 115.
  20. Haykin, S.(1994), "Neural networks: a comprehensive foundation", Macmillan, New York, 842.
  21. lslam, M. S., Pam, H. J., and Kwan, A. K. H.(1998), "Shear capacity of high strength concrete beams with their point of inflection within the shear span", Proc. Inst. Civil Eng., Structures and Buildings, 128(1) 91 -99. https://doi.org/10.1680/istbu.1998.30038
  22. Jackobsen, B. (1989), "High strength concrete in off shore structures", Design Aspects of HSC, CEB Bulletin dInformation, 193.
  23. Kani, M. W., Huggins, M. W., and Wittkopp, R. R.(1979), "Kani on shear in reinforced concrete", Dept. of Civil Eng., University of Toronto Press, Toronto, Canada, 225.
  24. Kim, J. K., and Park, Y. D.(1994), "Shear strength of reinforced high strength concrete beams without web reinforcement", Magazine of Concrete Research, 46(166), 7-16. https://doi.org/10.1680/macr.1994.46.166.7
  25. Mphonde, A. G., and Frantz, G. C.(1984), "Shear tests of high and low-strength concrete beams without stirrups", ACI J., 81(4), 350-357.
  26. Morsch, E.(1909), Concrete steel construction, 3rd ed., (1st ed. ln 1902), translated to English by E. P. Goodrich of Der Eisenbetonau, Eng. News Publish. Co, New York, 368.
  27. Papadakis, G.(1996), "Shear failure of reinforced concrete beams without stirrups", Ph. D. Thesis, Dept. Civil Eng., Aristotle University of Thessaloniki, Greece, (in Greek).
  28. Pellegrino, C., Bernardini, A., and Modena, C.(2002), "Shear failure of HSC beams with variable Shear Spanto-Depthratio", Proceeding of the 6th International Symposium on Utilisation of High Strength/High Performance Concrete, Edited by Koenig, Dehn, and Faust, Leipzig, Germany, 473-485.
  29. Podgorniak-Stanik, B.(1998), "The lnfluence of concrete strength, distribution of longitudinal reinforcement, amount of transverse reinforcement, and member size on shear strength of reinforced concrete members", M. A. Sc., Thesis, Dept. of Civil Eng., Universityof Toronto, Canada, 369.
  30. Rebeiz, K. S., Fente,J., and Frabizzio, M. A.(2001), "Effect of variables on shear strength of concrete beams", J. Materials in Civil Eng., ASCE, 13(6), 467-470. https://doi.org/10.1061/(ASCE)0899-1561(2001)13:6(467)
  31. Ritter, W.(1899), "Die bauweise hennebique", Schweizerische Bauzeitung", 33(7), 59-61
  32. Rumelhart, D. E.,Hinton, G. E., andwilliam, R. J.(1986), "Learning internal representation byerror propagation", Parallel Distributed Processing, J, Foundation, MlT Press, Cambridge, MA, 318-362.
  33. Salandra, M. A., and Ahmad, S. H.(1989), "Shear capacityof reinforced lightweight high-strength concretebeams", ACI Struct. J., 86(6), 697-704.
  34. Taylor, H. P. J.(1970), "lnvestigation of the forces carried across cracks in reinforced concrete beams in shear byinterlock of aggregate", Technical Report 42.447, Cement and Concrete Association, London, UK, 22.
  35. Taylor, H. P. J. (1972), "Shear strength of large beams", J. Struct. Div., ASCE, 98(11), 2473-2489.
  36. Thorenfeldt, E., and Drangsholt, G.(1990), "Shear capacity of reinforced high strength concrete beams", ACI 2nd International Symposium on HSC, ACl SP 121.8, American Concrete lnstitute, Farmington Hills, Michigan, 129-154.
  37. Vecchio, F.J.,and Collins, M. P. (1986) "The modified compression field theory for reinforced concreteelements subjected to shear," ACI J., 83(2), 219-231.
  38. Walraven, J. C.(1978), "The influence of depth on the shear strength of light weight concrete beams without shear reinforcement", Stevin Lab. Rep. No. 5-78-4, Delft University of Technology, the Netherlands.
  39. Walraven, J. C.(1995), "Shear friction in high strengthconcrete", Progress in Concrete Research, Delft University of Technology, the Netherlands, 4, 57-65
  40. Walther, R. (1987), "Potentialityof using high strength concrete in structures", First International Symposium on Utilization of High Strength Concrete, Stavanger, Norway, 365-378.
  41. Xie, Y., Ahmad, S.H., Yu, T., Hino, S., and Chung, W.(1994), "Shear ductility of reinforced concrete beams of normal and high strength concrete", ACI Struct. J., 91(2) 140-149.
  42. Yoon, Y. S., Cook, W. D., and Mitchell, D.(1996), "Minimum shear reinforcement in normal, medium andhighstrength concrete beams", ACI Struct. J., 93(5), 576-584.
  43. Zsutty, T. C.(1968), "Beam shear strength prediction by analysis ofexisting data", ACI J., 65(11), 943-951.
  44. Zsutty, T. C.(1971), "Shear strength predictions for separate categories of simple beam tests", ACI J., 68(2), 138-143.

피인용 문헌

  1. Knowledge-based prediction of shear strength of concrete beams without shear reinforcement vol.30, pp.6, 2008, https://doi.org/10.1016/j.engstruct.2007.10.008
  2. Experimental study on shear behavior of reinforced concrete beams with web horizontal reinforcement vol.8, pp.4, 2014, https://doi.org/10.1007/s11709-014-0080-1
  3. Artificial neural network application to estimate kinematic soil pile interaction response parameters vol.27, pp.9, 2007, https://doi.org/10.1016/j.soildyn.2006.12.009
  4. Predicting diagonal cracking strength of RC slender beams without stirrups using ANNs vol.12, pp.5, 2013, https://doi.org/10.12989/cac.2013.12.5.697
  5. Behaviour of reinforced self-consolidating concrete frames vol.160, pp.2, 2007, https://doi.org/10.1680/stbu.2007.160.2.95
  6. Artificial intelligence model for rheological properties of oil well cement slurries incorporating SCMs vol.24, pp.3, 2012, https://doi.org/10.1680/adcr.11.00015
  7. Neuro-fuzzy optimisation to model the phenomenon of failure by punching of a slab-column connection without shear reinforcement vol.47, pp.5, 2013, https://doi.org/10.12989/sem.2013.47.5.679
  8. Modeling and simulation of shear resistance of R/C beams using artificial neural network vol.344, pp.5, 2007, https://doi.org/10.1016/j.jfranklin.2005.12.005
  9. Neural networks modeling of shear strength of SFRC corbels without stirrups vol.10, pp.1, 2010, https://doi.org/10.1016/j.asoc.2009.06.012
  10. Proposed Shear Design Equations for FRP-Reinforced Concrete Beams Based on Genetic Algorithms Approach vol.19, pp.12, 2007, https://doi.org/10.1061/(ASCE)0899-1561(2007)19:12(1033)
  11. Predicting Shear Capacity of FRP-Reinforced Concrete Beams without Stirrups by Artificial Neural Networks, Gene Expression Programming, and Regression Analysis vol.2018, pp.1687-8094, 2018, https://doi.org/10.1155/2018/5157824
  12. GMDH-based prediction of shear strength of FRP-RC beams with and without stirrups vol.22, pp.2, 2005, https://doi.org/10.12989/cac.2018.22.2.197
  13. Numerical evaluation of effects of shear span, stirrup spacing and angle of stirrup on reinforced concrete beam behaviour vol.79, pp.3, 2021, https://doi.org/10.12989/sem.2021.79.3.309
  14. Torsional behaviour of high strength concrete beams with spiral reinforcement vol.22, pp.4, 2005, https://doi.org/10.1080/13287982.2021.1962489