한국해안해양공학회지 (Journal of Korean Society of Coastal and Ocean Engineers)

한국해안·해양공학회 (Korean Society of Coastal and Ocean Engineers)
권호 표지

이중절단정규분포의 적용을 통한 케이슨 방파제 기대활동량 평가의 향상

Improved Estimation for Expected Sliding Distance of Caisson Breakwaters by Employment of a Doubly-Truncated Normal Distribution

  • Kim Tae-Min (Research Center of Industrial Technology, Dept. of Civil Eng., Chonbuk National University) ;
  • Hwang Kyu-Nam (Research Center of Industrial Technology, Dept. of Civil Eng., Chonbuk National University) ;
  • Takayama Tomotsuka (Disaster Prevention Research Institute)
  • 발행 : 2005.12.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

본 연구는 기대활동량을 이용하는 케이슨 방파제의 신뢰성 설계법(레벨 III)에 대한 연구로서, 기대활동량의 향상된 평가를 위해 지금까지 이용되어온 정규(가우스)분포 대신 이중절단정규분포의 사용을 제안하고자 하며, 이에 대한 타당성을 제시하고자 한다. 따라서 본 연구에서는 확률적 개념에 근거한 기대활동량의 계산과정에서 Monte-Carlo모의 기법을 통한 불확정요소들의 영향을 반영하는 방법에 대한 설명과 함께 이중절단정규분포가 적용되어야만 하는 명확한 근거가 제시되며, 또한 기대활동량 평가시의 이중절단정규분포의 적용방법에 대한 자세한 설명이 주어진다. 본 논문에서는 케이슨 방파제만을 대상으로 이중절단정규분포를 적용하고 있으나, 이중절단정규분포의 적용은 다양한 해안구조물 및 타 공학 분야에도 적극 활용될 수 있으므로 향후 적극적인 활용이 기대된다.

The present study is deeply concerned with the reliability design method(Level III) for caisson breakwaters using expected sliding distance, and the objectives of this study are to propose the employment of a doubly-truncated normal distribution and to present the validity for it. In this study, therefore, the explanations are made for consideration of effects of uncertain factors, and a clear basis that the doubly-truncated normal distribution should be employed in the computation process of expected sliding distance by Monte-Carlo simulation is presented with introduction of the employment method. Even though only caisson breakwaters are treated in this paper, the employment of doubly-truncated normal distribution can be applied to various coastal structures as well as other engineering fields, and therefore it is expected that the present study will be extended in various fields.

키워드

참고문헌

  1. Goda, Y. and Takagi, H. (2000). A reliability design method of caisson breakwaters with optimal wave heights. Coastal Eng. J., 42(4), 357-487
  2. Goda, Y. (2001). Extreme wave statistics for reliability-based design of caisson breakwaters. Proc. of Int. workshop on Advanced Design of Maritime Structures in the 21st century, PHRI&MLIT, Japan, 1-13
  3. Hanzawa, M., Yamagata, N., Nishihara, T., Takahashi, S., Takayama, T. and Tomiyasu, R. (2003). Performance of composite breakwaters from the view point of expected sliding distance of caisson. Proc. of Coastal Structures 2003, ASCE, 283-294
  4. Investigation and Design Office of the Second Port Construction Bureau, Ministry of Transport. (1986). Uneveness on top surface of rubble mound
  5. Ikesue, S. (1999). Study on reliability design method of composite breakwaters using the expected sliding distance Master thesis, Kyoto University (in Japanese)
  6. Kim, T.M. and Takayama, T. (2002). The development of reliability design system for a caisson type breakwater. Fourth Int. Summer Symposium, JSCE, 183-186
  7. Kim, T.M. and Takayama, T. (2003). Computational Improvement for expected sliding distance of a caisson-type breakwater by introduction of a doubly-truncated normal distribution. Coastal Eng. J., 45(3), 387-419 https://doi.org/10.1142/S0578563403000816
  8. Kim, T.M. (2004). New estimation of sliding distance for improvement of breakwater reliability design. Ph. D thesis, Kyoto University
  9. Morihira, M., Kihara, C. and Horikawa, H. (1978). Friction factor of composite breakwater on rubble mound. Proc. 25th Japanese Conf. Coastal Eng., JSCE, 337-342 (in Japanese)
  10. Morihira, M. and Adachi, K (1979). Friction factor of composite breakwater on rubble mound (Second Rept). Proc. 26th Japanese Conf. Coastal Eng., JSCE, 446-450 (in Japanese)
  11. Nagao, T., Kadowaki, Y. and Terauchi, K. (1995). Evaluation of safety of breakwaters by the reliability based design method (1st report: Study on the safety against sliding). Report of the Port and Harbour Research Institute, 34( 1 ), 39-70 (in Japanese)
  12. Oumeraci, H. (1994). Review and analysis of vertical breakwater failure - lessons learned. Coastal Eng., 22, 3-29 https://doi.org/10.1016/0378-3839(94)90046-9
  13. Shimosako, K and Takahashi, S. (1998). Reliability design method of composite breakwater using expected sliding distance. Report of the Port and Harbour Research Institute, 37(3), 3-30 (in Japanese)
  14. Shimosako, K. and Takahashi, S. (1998). Application of deformation-based reliability design for coastal structures -expected sliding distance method of composite breakwaters. Proc. of Coastal Structures'99, ed.I.J.Losada, Spain, Balkemare, 363-371
  15. Takayama, T. and Fujii, H. (1991). Probabilistic estimation of stability of slide for caisson type breakwater. Report of the Port and Harbour Research Institute, 30(4), 35-64 (in Japanese)
  16. Takayama, T. and Ikeda, N. (1993). Estimation of sliding failure probability of present breakwaters for probabilistic design. Report of the Port and Harbour Research Institute, 31(5), 3-32
  17. Tanimoto, K., Haranaka, S., Takahashi, S., Komatsu, K, Todoroki, M. and Osato, M. (1976). An experimental investigation of wave reflection, overtopping and wave forces for several type of breakwater and sea walls. Tech. Note of the Port and Harbour Research Institute, 246, 38 (in Japanese)
  18. Tanimoto, K, Takahashi, S. and Myose, K (1984). Experimental study of random forces on upright sections of breakwaters. Report of the Port and Harbour Research Institute, 23(5), 47-99