DOI QR코드

DOI QR Code

Estimation of R-factor and Seismic Performance for RC IMRFs using N2 Method

N2 Method를 이용한 RC 중간모멘트 연성골조의 반응수정계수 및 내진성능 평가

  • Published : 2002.12.01

Abstract

Response Modification Factor(R-factor) approach is currently implemented to reflect inelastic ductile behavior of the structures and to reduce elastic spectral demands from earthquakes to the design level. However R factors were set empirically and simply based on the professional committee consensus on observed performance of building structures during past earthquakes. Consequently some major shortcomings linked to the current R factor approach have been pointed out. Using reinforced concrete intermediate moment-resisting frames(RC IMRFs), an analytical procedure is presented in this paper to establish R factor rationally. To this end, analytical R values were evaluated based on N2 Method and compared with the values recommended by IBC 2000. Overall, the analytical results correlated well with the code values. However the results also revealed that R factor might strongly depend on the system fundamental period. As evidenced by the interstory drift index(IDI) analysis results of this study, current R-factor based(or, Life Safety based) design tends to fail in fulfilling other implicit and hopeful performance objectives such as immediate Occupancy and Collapse Prevention. Performance based design(PBD) appears to be a promising approach to meet the multi level seismic performance objectives assigned to the building structures of nowadays.

반응수정계수는 구조물의 비탄성 거동을 설계에 반영하고 설계지진력 산정시 설계강도를 탄성범위 이내로 저감시키기 위한 목적으로 사용하고 있다. 그러나 설계코드에서 채택하고 있는 반응수정계수는 과거의 지진피해로부터 관찰된 보편적 구조성능에 기인한 경험치이므로, 주기에 따른 동적성능과 구조 시스템의 구성에 따른 내진성능을 정확히 대변하지 못하고 있다. 본 연구에서는 중간모멘트 연성골조를 대상으로 N2 Method를 이용하여 반응수정계수와 내진성능을 평가하였으며, 그 결과를 미국의 IBC 2000 코드와 비교하여 이론적 타당성을 검증하였다. 해석결과 코드에 제시된 반응수정계수와 잘 부합되는 것으로 나타났으나, 동일한 구조시스템의 경우에도 주기에 따라 비교적 큰 차이를 보였다. 성능목표에 따른 사용성 기준을 설정하여 IDI를 평가한 결과, 설계지진에 대한 성능목표가 건물에 대한 내진성능을 대변하기는 어려우며 PBD(Performance Based Design)에 의거한 합리적인 접근이 필요한 것으로 판단된다.

Keywords

References

  1. ATC, “Response modification factors,” ATC 3-06, Applied Technology Council, 1978.
  2. Bertero, V. V., “Evaluation of response reduction factors recommended by ATC and SEAOC,” Proceedings of the Third U.S. National Conference on Earthquake Engineering, Charleston, North Carolina, 1986.
  3. ATC, “Structural response modification factors,” ATC 19, Applied Technology Council, 1995.
  4. ATC, “A critical review of current approaches to earthquake-resistant design,” ATC 34, Applied Technology Council, Redwood City, 1996.
  5. ATC, “Seismic evaluation and retrofit of concrete buildings,”Applied Technology Council, ATC 40, Applied Technology Council, 1996.
  6. FEMA, “NEHRP guicelines for the seismic rehabilitationof buildings,” FEMA 273, Federal Emergency Management Agency, Washington D.C, 1997.
  7. Fajfar, Peter, “A nonlinear analysis method for performance-based seismic design,” M.EERI, 2000, pp. 573-592.
  8. FEMA, “NEHRP recommended provisions for seismicregulations for new buildings and other structures(Part 1 Provision),” FEMA 302, Federal Emergency Management Agency, Washington D.C, 1997.
  9. FEMA, “NEHRP recommended provisions for seismicregulations for new buildings and other structures(Part 2 Commentary),” FEMA 303, Federal EmergencyManagement Agency, Washington D.C, 1997.
  10. Betero, Raul and Bertero, D. V. V., “Performance-basedseismic engineering : the need for a reliable conceptualcomprehensive approach,” Earthquake Engineering andStructural Dynamics, 2002, pp. 627-650.
  11. BSSC, “NEHRP recommended provisions for the developmentof seismic regulations for new buildings,”Building Seismic Safety Council, Washington, D.C.,1988.
  12. Miranda, E. V. V. Bertero, “Evaluation of strengthreduction factors for earthquake-resistant design,” EarthquakeSpectra, EERI, Vol. 10, No. 2, 1994, pp. 357-379. https://doi.org/10.1193/1.1585778
  13. ACI Commite 318, “Building Code Requirements forStructure Concrete(ACI 318-99),” Portlane Cement Association,1999.
  14. 한과박소프트(주), neoMAX-3D ver.2.0, 2001
  15. IBC 2000, “International Building Code,” International code council, INC. 2000.