한국해양공학회지 (Journal of Ocean Engineering and Technology)

  • 제16권2호
  • /
  • Pages.38-43
  • /
  • 2002
  • /
  • 1225-0767(pISSN)
  • /
  • 2287-6715(eISSN)
한국해양공학회 (Korean Society of Ocean Engineers)
권호 표지

상하 비대칭 롤러를 이용한 이중곡면 성형의 변형특성에 대한 연구

Deformation Characteristics of Compound Curved Plate Bending by Asymmetric Rollers

  • 최양렬 (목포대학교 기계선박해양공학부) ;
  • 신종계 (서울대학교 조선해양공학과)
  • 발행 : 2002.04.01
PDF 다운로드
⟨ 이전 논문 다음 논문 ⟩

초록

Die-less forming is a cold forming process which is to bend thick flat plates into compound curved plates using two asymmetric rollers. This forming method has several advantages compared with line heating which is widely used to fabricate compound curved pieces in shipyards. The die-less forming, however, has scarcely been studied. Even the deformation mechanism in this forming process has not been understood clearly. So, in this paper, the deformation characteristics of die-less forming is investigated analytically and numerically. for the analytic investigation, slab method based on equilibrium equation is applied. And the mechanism of curvature generation is derived for the asymmetry in roller applied. And three dimensional numerical analyses are performed with realistic modeling of interactions between the rollers and work-piece using finite element program, ABAQUS. It is shown that curvature generation is mainly due to the difference of normal positive strain distribution between the top and bottom surface of the work-piece. And a convex-type curved plate is formed if the center region of the work-piece is rolled with asymmetric rollers of which the lower is larger than the upper in diameter.

키워드

참고문헌

  1. 한국해양공학회지 v.13 no.1 강판의 곡가공 시뮤레이션을 위한 전산시스템 개발. 이주성
  2. 대한조선학회논문집 v.34 no.3 간이 연탄소성 해석을 이용한 선상가열에 의한 판의 변형 예측에 관한 연구 장창두;서승일;고대은
  3. Ph. D. Thesis, Dept. of Naval Arch. & Ocean Eng Mechanics-based Production Information of the Primary Path for the Fabrication of Curved Shell Using Asymmetric Roller Press Choi, Y.R.
  4. J.of Basic Engineering, Trans. ASME v.88 Effects of Nonsymmetry in Strip Rolling on Single-roll Drive Mills Holbrook, R.L;Zorowski, C.F.
  5. Metal Forming-Mechanics and Metallurgy Hosford, W.F;Caddell, R.M
  6. J.of Materials Processing Technology v.52 An Analytical Approach to Asymmetric Hot-Sheet Rolling Considering the Effects of the Shear Stress and Internal Moment at the Roll Gap Hwang, Y.M;Tzou, G.Y https://doi.org/10.1016/0924-0136(94)01731-F
  7. Ph. D. Thesis, Dept. on Naval Arch & Ocean Eng. Relations Between Input Parameters and Residual Deformations in Line Heating Process Using Finite Element Method and Multi-Variate Analysis Lee, J.H
  8. Introduction to the Mechanics of a Continuous Medium Malvern, L.E.
  9. Ph. D. Thesis, Dept. of Ocean Eng. Mechanics of Die-less Forming of Doubly Curved Metal Shells Rady, E.F.
  10. J.of Hydrospace Technology v.2 no.1 Numerical Modeling for Systematization of Line Heating Process Shin, J.G;Kim, W.D;Kee, J.H
  11. Int. J. Mech. Sci v.33 no.5 Simulation of Ring Rolling Using a Rigid-plastic Finite Element Method Xu, S.G;Lian, J.C;Hawkyard, J.B https://doi.org/10.1016/0020-7403(91)90077-G