DOI QR코드

DOI QR Code

Stress path adapting Strut-and-Tie models in cracked and uncracked R.C. elements

  • Biondini, Fabio (Department of Structural Engineering, Technical University of Milan) ;
  • Bontempi, Franco (Department of Structural and Geotechnical Engineering, University of Rome "La Sapienza") ;
  • Malerba, Pier Giorgio (Department of Structural Engineering, Technical University of Milan)
  • Published : 2001.12.25

Abstract

In this paper, a general method for the automatic search for Strut-and-Tie (S&T) models representative of possible resistant mechanisms in reinforced concrete elements is proposed. The representativeness criterion here adopted is inspired to the principle of minimum strain energy and requires the consistency of the model with a reference stress field. In particular, a highly indeterminate pin-jointed framework of a given layout is generated within the assigned geometry of the concrete element and an optimum truss is found by the minimisation of a suitable objective function. Such a function allows us to search the optimum truss according to a reference stress field deduced through a F.E.A. and assumed as representative of the given continuum. The theoretical principles and the mathematical formulation of the method are firstly explained; the search for a S&T model suitable for the design of a deep beam shows the method capability in handling the reference stress path. Finally, since the analysis may consider the structure as linear-elastic or cracked and non-linear in both the component materials, it is shown how the proposed procedure allows us to verify the possibilities of activation of the design model, oriented to the serviceability condition and deduced in the linear elastic field, by following the evolution of the resistant mechanisms in the cracked non-linear field up to the structural failure.

Keywords

References

  1. Biondini, F. (1996), "Search for optimal Strut-and-Tie models in reinforced concrete elements", Dissertation, Post-Graduate School for Reinforced Concrete Structures "F.lli Pesenti", Tecnical University of Milan (in Italian).
  2. Biondini, F., Bontempi, F., and Malerba, P.G. (1996), "Search for Strut-and-Tie models by linear programming", Studi e Ricerche, Scuola di Specializzazione in Costruzioni in Cemento Armato, Politecnico di Milano, 17, 121-156 (in Italian).
  3. Biondini, F., Bontempi, F., and Malerba, P.G. (1999), "Optimal Strut-and-Tie models in reinforced concrete structures", Computer Assisted Mechanics and Engineering Sciences, 6(3-4), 279-293.
  4. Biondini, F., Bontempi, F., and Malerba, P.G. (2000), "The search for structural schemes by optimality criteria and soft-computing techniques", Proc. of Structural Morphology Conference, 179-187, Delft, The Netherlands, August 17-19.
  5. Blaauwendraad, J., and Hoogenboom, P.C.J. (1996), "Stringer panel model for structural concrete design", ACI Sruct. J., 93(3), 295-305.
  6. CEB (1982), Detailing of Concrete Structures, Bulletin DInformation, 150.
  7. Hadley, G. (1962), Linear Programming, Addison-Wesley, Reading (MA).
  8. Hemp, W.S. (1973), Optimum Structures, Clarendon Press, Oxford.
  9. IABSE (1991), Structural Concrete, Stuttgart 1991, 62.
  10. Kumar, P. (1978), "Optimal force transmission in reinforced concrete deep beams", Comput. & Struct., 8(2), 223-229. https://doi.org/10.1016/0045-7949(78)90026-3
  11. Livesley, R.K. (1975), Matrix Methods of Structural Analysis, Pergamon Press.
  12. Malerba, P.G. (1999), "Modelling of the diffusion zones in R.C. elements through discrete schemes", Proc. of the First Int. Conf. on Adv. in Struct. Eng. & Mech. (ASEM99), August 23-25, Seoul, Korea.
  13. Marti, P. (1985), "Basic tools of reinforced concrete beam design", ACI Struct. J., 82(1), 46-56.
  14. Nielsen, M.P. (1984), Limit Analysis and Concrete Plasticity, Prentice-Hall, Upper Saddle River (NJ).
  15. Schlaich, J., Schäfer, K., and Jennewin, M. (1987), "Toward a consistent design of structural concrete", PCI J., 32(3), 72-150.
  16. Schlaich, J., and Schäfer, K. (1991), "Design and detailing of structural concrete using Strut-and-Tie models", The Struct. Engineer, 69(6), 113-125.
  17. Vecchio, F.J., and Collins, M.P. (1986), "The modified compression field theory for reinforced concrete elements subjected to shear", ACI Struct. J., 83(2), 219-231.

Cited by

  1. Three-Dimensional Force Flow Paths and Reinforcement Design in Concrete via Stress-Dependent Truss-Continuum Topology Optimization vol.141, pp.1, 2015, https://doi.org/10.1061/(ASCE)EM.1943-7889.0000819
  2. Topological material distribution evaluation for steel plate reinforcement by using CCARAT optimizer vol.51, pp.5, 2014, https://doi.org/10.12989/sem.2014.51.5.793
  3. Strut-and-tie modelling of reinforced concrete beams using genetic algorithms optimization vol.23, pp.8, 2009, https://doi.org/10.1016/j.conbuildmat.2009.02.016
  4. On the Automatic Generation of Strut and Tie Patterns under Multiple Load Cases with Application to the Aseismic Design of Concrete Structures vol.13, pp.6, 2010, https://doi.org/10.1260/1369-4332.13.6.1167
  5. Topology design of optimizing material arrangements of beam-to-column connection frames with maximal stiffness vol.19, pp.4, 2012, https://doi.org/10.1016/j.scient.2012.06.004
  6. Layout design of reinforced concrete structures using two-material topology optimization with Drucker–Prager yield constraints vol.47, pp.1, 2013, https://doi.org/10.1007/s00158-012-0809-1
  7. Strut-and-Tie Design Methodology for Three-Dimensional Reinforced Concrete Structures vol.132, pp.6, 2006, https://doi.org/10.1061/(ASCE)0733-9445(2006)132:6(929)
  8. Generation of strut-and-tie models by topology design using different material properties in tension and compression vol.44, pp.2, 2011, https://doi.org/10.1007/s00158-011-0633-z
  9. Development of Strut-And-Tie Models in Deep Beams with Web Openings vol.10, pp.6, 2007, https://doi.org/10.1260/136943307783571427
  10. Topology optimization of reinforced concrete structures considering control of shrinkage and strength failure vol.157, 2015, https://doi.org/10.1016/j.compstruc.2015.05.009
  11. Topology optimization of the fiber-reinforcement retrofitting existing structures vol.50, pp.1, 2013, https://doi.org/10.1016/j.ijsolstr.2012.09.009
  12. Generating strut-and-tie patterns for reinforced concrete structures using topology optimization vol.87, pp.23-24, 2009, https://doi.org/10.1016/j.compstruc.2009.06.003
  13. Design versus Assessment of Concrete Structures Using Stress Fields and Strut-and-Tie Models vol.112, pp.5, 2015, https://doi.org/10.14359/51687710
  14. A numerical method to generate optimal load paths in plain and reinforced concrete structures vol.170, 2016, https://doi.org/10.1016/j.compstruc.2016.03.012
  15. Optimal FRP reinforcement of masonry walls out-of-plane loaded: A combined homogenization–topology optimization approach complying with masonry strength domain vol.153, 2015, https://doi.org/10.1016/j.compstruc.2015.02.004
  16. Performance-Based Optimization: A Review vol.10, pp.6, 2007, https://doi.org/10.1260/136943307783571418
  17. Evaluation of structural outrigger belt truss layouts for tall buildings by using topology optimization vol.43, pp.6, 2001, https://doi.org/10.12989/sem.2012.43.6.711
  18. Unified geometrical framework for the plastic design of reinforced concrete structures vol.21, pp.6, 2001, https://doi.org/10.1002/suco.201900440
  19. Generation of strut-and-tie models in concrete structures by topology optimization based on moving morphable components vol.53, pp.7, 2001, https://doi.org/10.1080/0305215x.2020.1781843